Flexible cellulose-based piezoelectric composite membrane involving PVDF and BaTiO3 synthesized with the assistance of TEMPO-oxidized cellulose nanofibrils.

High-performance flexible barium titanate (BaTiO3)-based piezoelectric devices have gained much attention. However, it is still a challenge to prepare flexible polymer/BaTiO3-based composite materials with uniform distribution and high performance due to the high viscosity of polymers. In this study, novel hybrid BaTiO3 particles were synthesized with assistance of TEMPO-oxidized cellulose nanofibrils (CNFs) via a low-temperature hydrothermal method and explored for their application in piezoelectric composites. Specifically, Ba2+ was adsorbed on uniformly dispersed CNFs with a large amount of negative charge on their surface, which nucleated, resulting in the synthesis of evenly dispersed CNF-BaTiO3. The obtained CNF-BaTiO3 possessed a uniform particle size, few impurities, high crystallinity and dispersity, high compatibility with the polymer substrate and surface activity due to the existence of CNFs. Subsequently, both polyvinylidene fluoride (PVDF) and TEMPO-oxidized CNFs were employed as piezoelectric substrates for the fabrication of a CNF/PVDF/CNF-BaTiO3 composite membrane with a compact structure, displaying the tensile strength of 18.61 ± 3.75 MPa and elongation at break of 3.06 ± 1.33%. Finally, a thin piezoelectric generator (PEG) was assembled, which output a considerable open-circuit voltage (4.4 V) and short-circuit current (200 nA), and could also power a light-emitting diode and charge a 1 µF capacitor to 3.66 V in 500 s. Its longitudinal piezoelectric constant (d 33) was 5.25 ± 1.04 pC N-1 even with a small thickness. It also exhibited high sensitivity to human movement, outputting a voltage of about 9 V and current of 739 nA for only a footstep. Thus, it exhibited good sensing property and energy harvesting property, presenting practical application prospects. This work provides a new idea for the preparation of hybrid BaTiO3 and cellulose-based piezoelectric composite materials.

Anisotropic Wooden Electromechanical Transduction Devices Enhanced by TEMPO Oxidization and PDMS.

In order to increase the number and contact probability of electric dipole on cellulose, acid and alkali treatment was employed to extract hemicellulose and lignin from original wood to gain a highly oriented cellulose frame. The combined means with 2,2,6,6-tetramethylpiperidine-1-oxyl-NaBr-NaClO oxidation and impregnation of PDMS with compression was subsequently used to enhance its mechanical performance and electromechanical conversion. The assembled wooden electromechanical device (10 mm × 10 mm × 1 mm) exhibits the maximum open-circuit voltage (V OC) of 11.75 V and short-circuit current (I SC) of 211.01 nA as stepped by foot. It can be sliced to fabricate a flexible sensor with high sensitivity displaying V OC of 2.88 V and I SC of 210.09 nA under the tapped state. Its highly oriented wood fiber makes it display significant anisotropy in terms of mechanical and electromechanical performance for multidirectional sense. This strategy will exactly provide reference for developing other high-performance piezoelectric devices.

Steady and Robust CNTs-Based Electric Heating Membrane Fabricated by Addition of Nanocellulose and Hot-Press Encapsulation.

Herein, a type of biomass-based electric heating membrane (EHM) with excellent stability was fabricated; this was achieved by incorporating carbon nanotubes (CNTs) into the nanofibrillated cellulose (NFC) as a natural dispersant and a biological substrate, as well as via the control of ultrasonic dispersion, grammage, and encapsulation using poly(dimethylsiloxane) (PDMS) with hot pressing. NFC entangles with CNTs in the form of an intertwined network and non-covalent interactions to fabricate a flexible EHM with steady electric heating performance; this formation is attributed to not only their similar morphology and surface-active groups but also the use of NFC that avoids additional disturbances in the overlapped interface among CNTs as far as possible. The obtained steady resistance varies as low as 5.1% under energized operation. In the encapsulated EHM (EM), PDMS was anchored on its surface by using hot pressing and an intertwined structure to enhance flexibility and robustness. The encapsulated membrane can be used in low-voltage applications, which require flexibility, waterproofing, and insulation.

A Nanofibrillated Cellulose-Based Electrothermal Aerogel Constructed with Carbon Nanotubes and Graphene.

Nanofibrillated cellulose (NFC) as an environmentally friendly substrate material has superiority for flexible electrothermal composite, while there is currently no research on porous NFC based electrothermal aerogel. Therefore, this work used NFC as a skeleton, combined with multi-walled carbon nanotubes (MWCNTs) and graphene (GP), to prepare NFC/MWCNTs/GP aerogel (CCGA) via a simple and economic freeze-drying method. The electrothermal CCGA was finally assembled after connecting CCGA with electrodes. The results show that when the concentration of the NFC/MWCNTs/GP suspension was 5 mg mL-1 and NFC amount was 80 wt.%, the maximum steady-state temperature rise of electrothermal CCGA at 3000 W m-2 and 2000 W m-2 was of about 62.0 °C and 40.4 °C, respectively. The resistance change rate of the CCGA was nearly 15% at the concentration of 7 mg mL-1 under the power density of 2000 W m-2. The formed three-dimensional porous structure is conducive to the heat exchange. Consequently, the electrothermal CCGA can be used as a potential lightweight substrate for efficient electrothermal devices.