Effects of non-stationary blur on texture biomarkers of bone using Ultra-High Resolution CT.

Purpose: To advance the development of radiomic models of bone quality using the recently introduced Ultra-High Resolution CT (UHR CT), we investigate inter-scan reproducibility of trabecular bone texture features to spatially-variant azimuthal and radial blurs associated with focal spot elongation and gantry rotation. Methods: The UHR CT system features 250×250 µm detector pixels and an x-ray source with a 0.4×0.5 mm focal spot. Visualization of details down to ~150 µm has been reported for this device. A cadaveric femur was imaged on UHR CT at three radial locations within the field-of-view: 0 cm (isocenter), 9 cm from the isocenter, and 18 cm from the isocenter; we expect the non-stationary blurs to worsen with increasing radial displacement. Gray level cooccurrence (GLCM) and gray level run length (GLRLM) texture features were extracted from 237 trabecular regions of interest (ROIs, 5 cm diameter) placed at corresponding locations in the femoral head in scans obtained at the different shifts. We evaluated concordance correlation coefficient (CCC) between texture features at 0 cm (reference) and at 9 cm and 18 cm. We also investigated whether the spatially-variant blurs affect K-means clustering of trabecular bone ROIs based on their texture features. Results: The average CCCs (against the 0 cm reference) for GLCM and GLRM features were ~0.7 at 9 cm. At 18 cm, the average CCCs were reduced to ~0.17 for GLCM and ~0.26 for GLRM. The non-stationary blurs are incorporated in radiomic features of cancellous bone, leading to inconsistencies in clustering of trabecular ROIs between different radial locations: an intersection-over-union overlap of corresponding (most similar) clusters between 0 cm and 9 cm shift was >70%, but dropped to <60% for the majority of corresponding clusters between 0 cm and 18 cm shift. Conclusion: Non-stationary CT system blurs reduce inter-scan reproducibility of texture features of trabecular bone in UHR CT, especially for locations >15 cm from the isocenter. Radiomic models of bone quality derived from UHR CT measurements at isocenter might need to be revised before application in peripheral body sites such as the hips.

Postoperative decrease of regional volumetric bone mineral density measured by quantitative computed tomography after lumbar fusion surgery in adjacent vertebrae.

We investigated the effect of posterior lumbar fusion surgery on the regional volumetric bone mineral density (vBMD) measured by quantitative computed tomography. Surgery negatively affected the regional vBMD in adjacent levels. Interbody fusion was independently associated with vBMD decline and preoperative epidural steroid injections (ESIs) were associated with less postoperative vBMD decline. INTRODUCTION: Few studies investigate postoperative BMD changes after lumbar fusion surgery utilizing quantitative computed tomography (QCT). Additionally, it remains unclear what preoperative and operative factors contribute to postoperative BMD changes. The purpose of this study is to investigate the effect of lumbar fusion surgery on regional volumetric bone mineral density (vBMD) in adjacent vertebrae and to identify potential modifiers for postoperative BMD change. METHODS: The data of patients undergoing posterior lumbar fusion with available pre- and postoperative CTs were reviewed. The postoperative changes in vBMD in the vertebrae one or two levels above the upper instrumented vertebra (UIV+1, UIV+2) and one level below the lower instrumented vertebra (LIV+1) were analyzed. As potential contributing factors, history of ESI, and the presence of interbody fusion, as well as various demographic/surgical factors, were included. RESULTS: A total of 90 patients were included in the study analysis. Mean age (±SD) was 62.1 ± 11.7. Volumetric BMD (±SD) in UIV+1 was 115.4 ± 36.9 mg/cm3 preoperatively. The percent vBMD change in UIV+1 was - 10.5 ± 12.9% (p < 0.001). UIV+2 and LIV+1 vBMD changes showed similar trends. After adjusting with the interval between surgery and the secondary CT, non-Caucasian race, ESI, and interbody fusion were independent contributors to postoperative BMD change in UIV+1. CONCLUSIONS: Posterior lumbar fusion surgery negatively affected the regional vBMDs in adjacent levels. Interbody fusion was independently associated with vBMD decline. Preoperative ESIs were associated with less postoperative vBMD decline, which was most likely a result of a preoperative decrease in vBMD due to ESIs.

Low volumetric bone density is a risk factor for early complications after spine fusion surgery.

This study aims to investigate lumbar spine (LS) volumetric bone density (vBMD) as a risk factor for complications (pseudoarthrosis, instrumentation failure, adjacent fractures), re-operation, and time to complication after fusion. INTRODUCTION: Lumbar spine (LS) fusion surgery is increasingly performed worldwide. Complications after fusion result in significant morbidity and healthcare costs. Multiple factors, including osteoporosis, have been suggested to contribute to risk of complications and re-operation. However, most studies have used DXA, which is subject to artifact in patients with spine pathology, and none have investigated the relationship between BMD and timing of post-operative complications. This study aims to investigate LS volumetric bone density (vBMD) as a risk factor for complications (pseudoarthrosis, instrumentation failure, adjacent fractures), re-operation, and time to complication after fusion. METHODS: We evaluated a cohort of 359 patients who had initial LS fusion surgery at our institution, had pre-operative LS CTs and post-operative imaging available for review. Demographic factors, smoking status, vBMD, and details of surgical procedure were related to likelihood and timing of post-operative complications. RESULTS: Mean age was 60 ± 14 years, vBMD 122 ± 37 g/cm3. Median follow-up was 11 months. Skeletal complications occurred in 47 patients (13%); 34 patients (10%) required re-operation. Low vBMD (directly measured and estimated using HU) and smoking were associated with increased risk of skeletal complications. Each increase in baseline vBMD of 10 g/cm3 decreased the complication hazard and increased the complication-free duration in time-to-event analysis (hazard ratio 0.91, 95% CI 0.83-0.98, p < 0.02). CONCLUSIONS: Low vBMD was a significant risk factor for early post-operative complications in patients undergoing LS fusion. Prospective studies are needed to confirm these findings and to elucidate the optimal timing for follow-up and strategies for prevention of post-operative complications in this population.

Quantitative Evaluation of Bone Microstructure using High-Resolution Extremity Cone-Beam CT with a CMOS Detector.

PURPOSE: A high-resolution cone-beam CT (CBCT) system for extremity imaging has been developed using a custom complementary metal-oxide-semiconductor (CMOS) x-ray detector. The system has spatial resolution capability beyond that of recently introduced clinical orthopedic CBCT. We evaluate performance of this new scanner in quantifying trabecular microstructure in subchondral bone of the knee. METHODS: The high-resolution scanner uses the same mechanical platform as the commercially available Carestream OnSight 3D extremity CBCT, but replaces the conventional amorphous silicon flat-panel detector (a-Si:H FPD with 0.137 mm pixels and a ~0.7 mm thick scintillator) with a Dalsa Xineos3030 CMOS detector (0.1 mm pixels and a custom 0.4 mm scintillator). The CMOS system demonstrates ~40% improved spatial resolution (FWHM of a ~0.1 mm tungsten wire) and ~4× faster scan time than FPD-based extremity CBCT (FPD-CBCT). To investigate potential benefits of this enhanced spatial resolution in quantitative assessment of bone microstructure, 26 trabecular core samples were obtained from four cadaveric tibias and imaged using FPD-CBCT (75 µm voxels), CMOS-CBCT (75 µm voxels), and reference micro-CT (µCT, 15 µm voxels). CBCT bone segmentations were obtained using local Bernsen's thresholding combined with global histogram-based pre-thresholding; µCT segmentation involved Otsu's method. Measurements of trabecular thickness (Tb.Th), spacing (Tb.Sp), number (Tb.N) and bone volume (BV/TV) were performed in registered regions of interest in the segmented CBCT and µCT reconstructions. RESULTS: CMOS-CBCT achieved noticeably improved delineation of trabecular detail compared to FPD-CBCT. Correlations with reference µCT for metrics of bone microstructure were better for CMOS-CBCT than FPD-CBCT, in particular for Tb.Th (increase in Pearson correlation from 0.84 with FPD-CBCT to 0.96 with CMOS-CBCT) and Tb.Sp (increase from 0.80 to 0.85). This improved quantitative performance of CMOS-CBCT is accompanied by a reduction in scan time, from ~60 sec for a clinical high resolution protocol on FPD-CBCT to ~17 sec for CMOS-CBCT. CONCLUSION: The CMOS-based extremity CBCT prototype achieves improved performance in quantification of bone microstructure, while retaining other diagnostic capabilities of its FPD-based precursor, including weight-bearing imaging. The new system offers a promising platform for quantitative imaging of skeletal health in osteoporosis and osteoarthritis.

Detection of the Stellate and Thoracic Sympathetic Chain Ganglia with High-Resolution 3D-CISS MR Imaging.

BACKGROUND AND PURPOSE: Despite the importance of the sympathetic nervous system in homeostasis and its putative role in various disease states, little is known regarding our ability to image the sympathetic chain and sympathetic chain ganglia, perhaps owing to their small size. In this retrospective study, we sought to evaluate the normal anatomy of the sympathetic chain ganglia and assess the detectability of the sympathetic chain and sympathetic chain ganglia on high-resolution 3D-CISS images. MATERIALS AND METHODS: This study included 29 patients who underwent 3D-CISS MR imaging of the thoracic spine for reasons unrelated to abnormalities of the sympathetic nervous system. Patients with a prior spinal operation or visible spinal pathology were excluded. The sympathetic chain ganglia were evaluated using noncontrast 3D-CISS MR imaging. Statistical analyses included t tests and measures of central tendency. The Cohen κ statistic was calculated to evaluate interrater reliability. RESULTS: The stellate ganglion and thoracic chain ganglia were identified in all subjects except at the T10-T11 and T11-T12 levels. The stellate ganglion was found inferomedial to the subclavian artery and anterior and inferior to the transverse process of C7 in all subjects. Thoracic sympathetic chain ganglia were identified ventral to the costovertebral junction in all subjects from T2 to T10. There was strong interobserver agreement for the detection of the sympathetic chain ganglia with κ > 0.80. The size, shape, and location of these structures corresponded with gross anatomic and surgical observations. CONCLUSIONS: The thoracic sympathetic chain ganglia can be identified on precontrast 3D-CISS MR imaging. This technique may aid in the initial evaluation of stellate ganglion and/or sympathetic chain ganglia size and signal change for comparison in future studies.

Osteoarthritis year in review 2017: updates on imaging advancements.

OBJECTIVE: This narrative review covers original research publications related to imaging advancements in osteoarthritis (OA) published in the English language between 1st April 2016 and 30th April 2017. METHODS: Relevant human studies (excluding pre-clinical and in vitro studies), were searched and selected from PubMed database using the search terms of "osteoarthritis (OA)" in combination with "radiography", "magnetic resonance imaging (MRI)", "computed tomography (CT)", "ultrasound", "positron emission tomography (PET)," "single-photon emission computed tomography (SPECT)," and "scintigraphy". The included studies were sorted according to their relevance, novelty, and impact. Original research articles with both imaging advancements and novel clinical information were discussed in this review. RESULTS: A large portion of the published studies were focused on MRI-based semi-quantitative and quantitative (morphological and structural) metrics of the knee joint to assess OA-related structural damages. New imaging technologies, such as PET, have been investigated for OA diagnosis and characterization, the delineation of predictive factors for OA progression, and to monitor the treatment responses. CONCLUSION: Advanced imaging modalities play a pivotal role in OA research, and make a significant contribution to our understanding of OA diagnosis, pathogenesis, risk stratification, and prognosis.

Tract-Specific Diffusion Tensor Imaging in Cervical Spondylotic Myelopathy Before and After Decompressive Spinal Surgery: Preliminary Results.

PURPOSE: Diffusion tensor imaging (DTI) metrics of the cervical spinal cord in patients with cervical spondylotic myelopathy (CSM) were compared to those measured in healthy volunteers, using tract-specific region of interests (ROIs) across all cervical intervertebral disc levels. METHODS: Magnetic resonance (MR) imaging of the cervical spinal cord was performed in four patients with CSM and in five healthy volunteers on a 3-T MR scanner. Region-specific fractional anisotropy (FA) and mean diffusivity (MD) were calculated on axial imaging with ROI placement in the anterior, lateral, and posterior regions of the spinal cord. FA and MD were also calculated on sagittal acquisitions. Nonparametric statistical tests were used to compare controls and patients before and after surgery. RESULTS: FA values were significantly lower (p = 0.050) and MD values were significantly higher (p = 0.014) in CSM patients measured at level of maximal compression before surgery than in healthy controls in lateral and posterior ROIs, respectively. In posterior ROIs, MD values were significantly higher in patients before surgery compared to controls at all levels except C7-T1. CONCLUSION: Patients with CSM may demonstrate region-specific changes in DTI metrics when compared to healthy controls. Changes in DTI metrics may also occur at levels remote from site of compression.

Atlas of radiographic features of osteoarthritis of the ankle and hindfoot.

OBJECTIVE: To develop a radiographic atlas of osteoarthritis (OA) for use as a template and guide for standardized scoring of radiographic features of OA of the ankle and hindfoot joints. METHOD: Under Institutional Review Board approval, ankle and hindfoot images were selected from a cohort study and from among cases that underwent ankle radiography during a 6-month period at Duke University Medical Center. Missing OA pathology was obtained through supplementation of cases with the assistance of a foot and ankle specialist in Orthopaedic surgery and a musculoskeletal radiologist. Images were obtained and reviewed without patient identifying information. Images went through multiple rounds of review and final images were selected by consensus of the study team. For intra-rater and inter-rater reliability, the kappa statistic was calculated for two readings by three musculoskeletal radiologists, a minimum of two weeks apart, of ankle and hindfoot radiographs from 30 anonymized subjects. RESULTS: The atlas demonstrates individual radiographic features (osteophyte and joint space narrowing (JSN)) and Kellgren-Lawrence grade for all aspects of the talocrural (ankle joint proper) and talocalcaneal (subtalar) joints. Reliability of scoring based on the atlas was quite good to excellent for most features indicated. Additional examples of ankle joint findings are illustrated including sclerosis, os trigonum, subchondral cysts and talar tilt. CONCLUSIONS: It is anticipated that this atlas will assist with standardization of scoring of ankle and hindfoot OA by basic and clinical OA researchers.

Glenoid notch MRI findings do not predict normal variants of the anterior and superior labrum.

AIM: To determine (1) the relationship of a glenoid notch to the presence of a normal labral variant in the anterior-superior glenoid labrum; (2) the inter- and intra-observer reliability of recognising a glenoid notch; and (3) whether magnetic resonance arthrography (MRA) is more reliable than non-contrast magnetic resonance imaging (MRI) in visualising a glenoid notch. MATERIALS AND METHODS: From 1995 through 2010, 104 patients underwent MRI or MRA before diagnostic shoulder arthroscopy by the senior author. Five blinded musculoskeletal radiologists independently read the images twice to evaluate for the presence or absence of a glenoid notch. Fifty-nine (57%) patients had normal anterior-superior labral variants. The authors calculated the relationship of the readings to the arthroscopically determined presence or absence of a normal labral variant and the reading's diagnostic performance and rater reliability. RESULTS: On average, 38% (range 9-65%) of the glenoid scans were read as notched. The sensitivity, specificity, positive predictive value, and negative predictive value of the notch relative to the presence of a normal variant were 43.1%, 71.2%, 70.2%, and 48% versus 44.3%, 77.5%, 79.4%, and 56.1% for MRI and MRA, respectively. The overall average intra-observer κ-values were 0.438 (range 0.203-0.555) and 0.346 (range -0.102 to 0.570) for MRI and MRA, respectively. The average interobserver intra-class correlation coefficient reliability values were 0.730 (range 0.693-0.760) and 0.614 (range 0.566-0.662) for MRI and MRA, respectively. CONCLUSIONS: A notched glenoid on MRI lacks sufficient diagnostic performance and rater reliability for the clinical detection and prediction of normal anterior-superior labral variants.

Assessment of image quality in soft tissue and bone visualization tasks for a dedicated extremity cone-beam CT system.

OBJECTIVE: To assess visualization tasks using cone-beam CT (CBCT) compared to multi-detector CT (MDCT) for musculoskeletal extremity imaging. METHODS: Ten cadaveric hands and ten knees were examined using a dedicated CBCT prototype and a clinical multi-detector CT using nominal protocols (80 kVp-108mAs for CBCT; 120 kVp- 300 mAs for MDCT). Soft tissue and bone visualization tasks were assessed by four radiologists using five-point satisfaction (for CBCT and MDCT individually) and five-point preference (side-by-side CBCT versus MDCT image quality comparison) rating tests. Ratings were analyzed using Kruskal-Wallis and Wilcoxon signed-rank tests, and observer agreement was assessed using the Kappa-statistic. RESULTS: Knee CBCT images were rated "excellent" or "good" (median scores 5 and 4) for "bone" and "soft tissue" visualization tasks. Hand CBCT images were rated "excellent" or "adequate" (median scores 5 and 3) for "bone" and "soft tissue" visualization tasks. Preference tests rated CBCT equivalent or superior to MDCT for bone visualization and favoured the MDCT for soft tissue visualization tasks. Intraobserver agreement for CBCT satisfaction tests was fair to almost perfect (κ ~ 0.26-0.92), and interobserver agreement was fair to moderate (κ ~ 0.27-0.54). CONCLUSION: CBCT provided excellent image quality for bone visualization and adequate image quality for soft tissue visualization tasks. KEY POINTS: • CBCT provided adequate image quality for diagnostic tasks in extremity imaging. • CBCT images were "excellent" for "bone" and "good/adequate" for "soft tissue" visualization tasks. • CBCT image quality was equivalent/superior to MDCT for bone visualization tasks.

Cascaded systems analysis of photon counting detectors.

PURPOSE: Photon counting detectors (PCDs) are an emerging technology with applications in spectral and low-dose radiographic and tomographic imaging. This paper develops an analytical model of PCD imaging performance, including the system gain, modulation transfer function (MTF), noise-power spectrum (NPS), and detective quantum efficiency (DQE). METHODS: A cascaded systems analysis model describing the propagation of quanta through the imaging chain was developed. The model was validated in comparison to the physical performance of a silicon-strip PCD implemented on an experimental imaging bench. The signal response, MTF, and NPS were measured and compared to theory as a function of exposure conditions (70 kVp, 1-7 mA), detector threshold, and readout mode (i.e., the option for coincidence detection). The model sheds new light on the dependence of spatial resolution, charge sharing, and additive noise effects on threshold selection and was used to investigate the factors governing PCD performance, including the fundamental advantages and limitations of PCDs in comparison to energy-integrating detectors (EIDs) in the linear regime for which pulse pileup can be ignored. RESULTS: The detector exhibited highly linear mean signal response across the system operating range and agreed well with theoretical prediction, as did the system MTF and NPS. The DQE analyzed as a function of kilovolt (peak), exposure, detector threshold, and readout mode revealed important considerations for system optimization. The model also demonstrated the important implications of false counts from both additive electronic noise and charge sharing and highlighted the system design and operational parameters that most affect detector performance in the presence of such factors: for example, increasing the detector threshold from 0 to 100 (arbitrary units of pulse height threshold roughly equivalent to 0.5 and 6 keV energy threshold, respectively), increased the f50 (spatial-frequency at which the MTF falls to a value of 0.50) by ∼30% with corresponding improvement in DQE. The range in exposure and additive noise for which PCDs yield intrinsically higher DQE was quantified, showing performance advantages under conditions of very low-dose, high additive noise, and high fidelity rejection of coincident photons. CONCLUSIONS: The model for PCD signal and noise performance agreed with measurements of detector signal, MTF, and NPS and provided a useful basis for understanding complex dependencies in PCD imaging performance and the potential advantages (and disadvantages) in comparison to EIDs as well as an important guide to task-based optimization in developing new PCD imaging systems.

High-Performance Soft-Tissue Imaging in Extremity Cone-Beam CT.

PURPOSE: Clinical performance studies of an extremity cone-beam CT (CBCT) system indicate excellent bone visualization, but point to the need for improvement of soft-tissue image quality. To this end, a rapid Monte Carlo (MC) scatter correction is proposed, and Penalized Likelihood (PL) reconstruction is evaluated for noise management. METHODS: The accelerated MC scatter correction involved fast MC simulation with low number of photons implemented on a GPU (107 photons/sec), followed by Gaussian kernel smoothing in the detector plane and across projection angles. PL reconstructions were investigated for reduction of imaging dose for projections acquired at ~2 mGy. RESULTS: The rapid scatter estimation yielded root-mean-squared-errors of scatter projections of ~15% of peak scatter intensity for 5·106 photons/projection (runtime ~0.5 sec/projection) and 25% improvement in fat-muscle contrast in reconstructions of a cadaveric knee. PL reconstruction largely restored soft-tissue visualization at 2 mGy dose to that of 10 mGy FBP image. CONCLUSION: The combination of rapid (5-10 minutes/scan) MC-based, patient-specific scatter correction and PL reconstruction offers an important means to overcome the current limitations of extremity CBCT in soft-tissue imaging.

Dual-energy cone-beam CT with a flat-panel detector: effect of reconstruction algorithm on material classification.

PURPOSE: Cone-beam CT (CBCT) with a flat-panel detector (FPD) is finding application in areas such as breast and musculoskeletal imaging, where dual-energy (DE) capabilities offer potential benefit. The authors investigate the accuracy of material classification in DE CBCT using filtered backprojection (FBP) and penalized likelihood (PL) reconstruction and optimize contrast-enhanced DE CBCT of the joints as a function of dose, material concentration, and detail size. METHODS: Phantoms consisting of a 15 cm diameter water cylinder with solid calcium inserts (50-200 mg/ml, 3-28.4 mm diameter) and solid iodine inserts (2-10 mg/ml, 3-28.4 mm diameter), as well as a cadaveric knee with intra-articular injection of iodine were imaged on a CBCT bench with a Varian 4343 FPD. The low energy (LE) beam was 70 kVp (+0.2 mm Cu), and the high energy (HE) beam was 120 kVp (+0.2 mm Cu, +0.5 mm Ag). Total dose (LE+HE) was varied from 3.1 to 15.6 mGy with equal dose allocation. Image-based DE classification involved a nearest distance classifier in the space of LE versus HE attenuation values. Recognizing the differences in noise between LE and HE beams, the LE and HE data were differentially filtered (in FBP) or regularized (in PL). Both a quadratic (PLQ) and a total-variation penalty (PLTV) were investigated for PL. The performance of DE CBCT material discrimination was quantified in terms of voxelwise specificity, sensitivity, and accuracy. RESULTS: Noise in the HE image was primarily responsible for classification errors within the contrast inserts, whereas noise in the LE image mainly influenced classification in the surrounding water. For inserts of diameter 28.4 mm, DE CBCT reconstructions were optimized to maximize the total combined accuracy across the range of calcium and iodine concentrations, yielding values of ∼ 88% for FBP and PLQ, and ∼ 95% for PLTV at 3.1 mGy total dose, increasing to ∼ 95% for FBP and PLQ, and ∼ 98% for PLTV at 15.6 mGy total dose. For a fixed iodine concentration of 5 mg/ml and reconstructions maximizing overall accuracy across the range of insert diameters, the minimum diameter classified with accuracy >80% was ∼ 15 mm for FBP and PLQ and ∼ 10 mm for PLTV, improving to ∼ 7 mm for FBP and PLQ and ∼ 3 mm for PLTV at 15.6 mGy. The results indicate similar performance for FBP and PLQ and showed improved classification accuracy with edge-preserving PLTV. A slight preference for increased smoothing of the HE data was found. DE CBCT discrimination of iodine and bone in the knee was demonstrated with FBP and PLTV at 6.2 mGy total dose. CONCLUSIONS: For iodine concentrations >5 mg/ml and detail size ∼ 20 mm, material classification accuracy of >90% was achieved in DE CBCT with both FBP and PL at total doses <10 mGy. Optimal performance was attained by selection of reconstruction parameters based on the differences in noise between HE and LE data, typically favoring stronger smoothing of the HE data, and by using penalties matched to the imaging task (e.g., edge-preserving PLTV in areas of uniform enhancement).

Design and development of a mobile image overlay system for needle interventions.

Previously, a static and adjustable image overlay systems were proposed for aiding needle interventions. The system was either fixed to a scanner or mounted over a large articulated counterbalanced arm. Certain drawbacks associated with these systems limited the clinical translation. In order to minimize these limitations, we present the mobile image overlay system with the objective of reduced system weight, smaller dimension, and increased tracking accuracy. The design study includes optimal workspace definition, selection of display device, mirror, and laser source. The laser plane alignment, phantom design, image overlay plane calibration, and system accuracy validation methods are discussed. The virtual image is generated by a tablet device and projected into the patient by using a beamsplitter mirror. The viewbox weight (1.0 kg) was reduced by 8.2 times and image overlay plane tracking precision (0.21 mm, STD = 0.05) was improved by 5 times compared to previous system. The automatic self-calibration of the image overlay plane was achieved in two simple steps and can be done away from patient table. The fiducial registration error of the physical phantom to scanned image volume registration was 1.35 mm (STD = 0.11). The reduced system weight and increased accuracy of optical tracking should enable the system to be hand held by the physician and explore the image volume over the patient for needle interventions.

High-resolution 3T MR neurography of the brachial plexus and its branches, with emphasis on 3D imaging.

With advancement in 3D imaging, better fat-suppression techniques, and superior coil designs for MR imaging and the increasing availability and use of 3T magnets, the visualization of the complexity of the brachial plexus has become facile. The relevant imaging findings are described for normal and pathologic conditions of the brachial plexus. These radiologic findings are supported by clinical and/or EMG/surgical data, and corresponding high-resolution MR neurography images are illustrated. Because the brachial plexus can be affected by a plethora of pathologies, resulting in often serious and disabling complications, a better radiologic insight has great potential in aiding physicians in rendering superior services to patients.

Anatomic MR imaging and functional diffusion tensor imaging of peripheral nerve tumors and tumorlike conditions.

BACKGROUND AND PURPOSE: A number of benign and malignant peripheral nerve tumor and tumorlike conditions produce similar imaging features on conventional anatomic MR imaging. Functional MR imaging using DTI can increment the diagnostic performance in differentiation of these lesions. Our aim was to evaluate the role of 3T anatomic MR imaging and DTI in the characterization of peripheral nerve tumor and tumorlike conditions. MATERIALS AND METHODS: Twenty-nine patients (13 men, 16 women; mean age, 41±18 years; range, 11-83 years) with a nerve tumor or tumorlike condition (25 benign, 5 malignant) underwent 3T MR imaging by using anatomic (n=29), functional diffusion, DWI (n=21), and DTI (n=24) techniques. Images were evaluated for image quality (3-point scale), ADC of the lesion, tractography, and fractional anisotropy of nerves with interobserver reliability in ADC and FA measurements. RESULTS: No significant differences were observed in age (benign, 40±18 versus malignant, 45±19 years) and sex (benign, male/female=12:12 versus malignant, male/female=3:2) (P>.05). All anatomic (29/29, 100%) MR imaging studies received "good" quality; 20/21 (95%) DWI and 21/24 (79%) DTI studies received "good" quality. ADC of benign lesions (1.848±0.40×10(-3) mm2/s) differed from that of malignant lesions (0.900±0.25×10(-3) mm2/s, P<.001) with excellent interobserver reliability (ICC=0.988 [95% CI, 0.976-0.994]). There were no FA or ADC differences between men and women (P>.05). FA of involved nerves was lower than that in contralateral healthy nerves (P<.001) with excellent interobserver reliability (ICC=0.970 [95% CI, 0.946-0.991]). ADC on DTI and DWI was not statistically different (P>.05), with excellent intermethod reliability (ICC=0.943 [95% CI, 0.836-0.980]). Tractography differences were observed in benign and malignant lesions. CONCLUSIONS: 3T MR imaging and DTI are valuable methods for anatomic and functional evaluation of peripheral nerve lesions with excellent interobserver reliability. While tractography and low FA provide insight into neural integrity, low diffusivity values indicate malignancy in neural masses.

Noise Reduction in Material Decomposition for Low-Dose Dual-Energy Cone-Beam CT.

PURPOSE: Dual-energy cone-beam CT (DE-CBCT) is an emerging technology with potential application in diagnostic imaging and image-guided interventions. This paper reports DE-CBCT feasibility and investigates decomposition algorithms for maximizing low-dose performance for reconstruction-based DE decomposition. A framework of binary decision theory is used to examine the accuracy of DE decompositions obtained from analytical reconstructions of differentially filtered low-energy (LE) and high-energy (HE) data and from penalized likelihood (PL) reconstructions with differential regularization using quadratic and total variation penalties. METHODS: Accurate DE-CBCT decomposition benefits from consideration of all system noise components. Filtered backprojection (FBP) reconstruction-based decomposition was investigated with differential filtering of LE and HE data. Penalized likelihood reconstruction-based decomposition with differential regularization was hypothesized to further improve low-dose performance, especially when coupled with regularization through a total variation edge preserving penalty that encourages piecewise smooth images. Performance of decomposition was assessed in terms of a binary hypothesis framework of sensitivity, specificity, and accuracy. Studies involved experiments on a DE-CBCT testbench, phantoms of variable material type and concentration, and cadavers (knee arthrography). RESULTS: Studies support the overall feasibility of accurate, low-dose DE-CBCT at concentration down to 5 mg/ml (iodine), dose ~3-6 mGy, and accuracy of material classification ~90%. Reconstruction-based decomposition with quadratic PL performed comparably to FBP. PL with a total variation penalty provided edge preservation and piecewise smooth images that aided DE classification and achieved improved performance over FBP and quadratic PL, reaching accuracy of ~0.98 for 2 mg/mL iodine at 3.2 mGy, compared to approx. 0.9 for FBP and quadratic PL. CONCLUSIONS: Accurate material decomposition with DE-CBCT is feasible at low dose and benefits from a rigorous assessment of noise mechanisms among various reconstruction-based techniques. The work points to the potential for non-linear iterative reconstruction methods for high-quality decomposition at low material concentration and dose.

Peripheral Quantitative CT (pQCT) Using a Dedicated Extremity Cone-Beam CT Scanner.

PURPOSE: We describe the initial assessment of the peripheral quantitative CT (pQCT) imaging capabilities of a cone-beam CT (CBCT) scanner dedicated to musculoskeletal extremity imaging. The aim is to accurately measure and quantify bone and joint morphology using information automatically acquired with each CBCT scan, thereby reducing the need for a separate pQCT exam. METHODS: A prototype CBCT scanner providing isotropic, sub-millimeter spatial resolution and soft-tissue contrast resolution comparable or superior to standard multi-detector CT (MDCT) has been developed for extremity imaging, including the capability for weight-bearing exams and multi-mode (radiography, fluoroscopy, and volumetric) imaging. Assessment of pQCT performance included measurement of bone mineral density (BMD), morphometric parameters of subchondral bone architecture, and joint space analysis. Measurements employed phantoms, cadavers, and patients from an ongoing pilot study imaged with the CBCT prototype (at various acquisition, calibration, and reconstruction techniques) in comparison to MDCT (using pQCT protocols for analysis of BMD) and micro-CT (for analysis of subchondral morphometry). RESULTS: The CBCT extremity scanner yielded BMD measurement within ±2-3% error in both phantom studies and cadaver extremity specimens. Subchondral bone architecture (bone volume fraction, trabecular thickness, degree of anisotropy, and structure model index) exhibited good correlation with gold standard micro-CT (error ~5%), surpassing the conventional limitations of spatial resolution in clinical MDCT scanners. Joint space analysis demonstrated the potential for sensitive 3D joint space mapping beyond that of qualitative radiographic scores in application to non-weight-bearing versus weight-bearing lower extremities and assessment of phalangeal joint space integrity in the upper extremities. CONCLUSION: The CBCT extremity scanner demonstrated promising initial results in accurate pQCT analysis from images acquired with each CBCT scan. Future studies will include improved x-ray scatter correction and image reconstruction techniques to further improve accuracy and to correlate pQCT metrics with known pathology.