Optical Trajectory Manipulations Using the Self-Written Waveguide Technique.

This study is novel for several reasons: We used a thin drop cast layer of dry photosensitive materials to study the behaviors of wet photopolymer media using microscopic distances during the Self-Written Waveguide (SWW) process; then, we examined the self-trajectories formed inside the solid material. The results provide a framework for theoretical and experimental examinations by handling the effects of manipulating the alignment of fibers. The other main advantage of these techniques is their lightweight, easy to process, highly flexible, and ultimately low-cost nature. First, the SWW process in wet photopolymer media (liquid solutions) was examined under three cases: single-, counter-, and co-fiber exposure. Then, the SWWs formed inside the solid material were examined along with the effects of manipulating the alignment of the fibers. In all cases, high precision measurements were used to position the fiber optic cables (FOCs) before exposure using a microscope. The self-writing process was indirectly monitored by observing (imaging) the light emerging from the side of the material sample during SWW formation. In this way, we examined the optical waveguide trajectories formed in Acrylamide/Polyvinyl Alcohol (AA/PVA), a photopolymer material (sensitized at 532 nm). First, the transmission of light by this material is characterized. Then, the bending and merging of the waveguides that occur are investigated. The predictions of our model are shown to qualitatively agree with the observed trajectories. The largest index changes taking place at any time during exposure, i.e., during SWW formation, are shown to take place at the positions where the largest exposure light intensity is present. Typically, such maxima exist close to the input face. The first maximum is referred to as the location of the Primary Eye. Other local maxima also appear further along the SWW and are referred to as Secondary Eyes, i.e., eyes deeper within the material.

Improving the uniformity of holographic recording using multilayer photopolymer. Part I. Theoretical analysis.

An experimental and theoretical investigation of the preparation and exposure of multilayer photosensitive materials is presented. It is shown how the recorded change in the refractive index in each layer depends on the dye (photosensitizer) concentrations in each layer. It is also shown how the photosensitive material properties in each layer can be controlled to optimize some recording characteristics for particular applications. To do so, a set of equations, predicting the amplitude of higher harmonics refractive index amplitudes induced in the material layers with depth during exposure, is derived. This results in a technique for varying the dye concentration in each layer of a multilayer, so as to optimize volume diffraction grating performance. In part I of this paper, the 3D nonlocal photopolymerization-driven diffusion (NPDD) model is applied to calculate the resulting combined multilayer absorption and polymerization processes. The NPDD describes the time-varying behaviors taking place during exposure in such photopolymer materials. Simulations are performed for an acrylamide/polyvinyl alcohol-based photopolymer containing erythrosine-B dye. It is predicted that, in general, non-uniform gratings are formed, with the resulting refractive index being distorted both from the ideal sinusoidal cross-sectional spatial distribution and also with depth. This agrees with previous results indicating that increasing the thickness of a single photopolymer layer does not in practice lead to ever-increasing angular selectivity. In part II of this paper, it is confirmed experimentally that a suitably modified multilayer can be used to increase grating angular selectivity, i.e., reduce the width of the off-Bragg replay curve.

Improving the uniformity of holographic recording using multi-layer photopolymer: Part II. Experimental results.

In the first part of this study, a 3D nonlocal photopolymerization driven diffusion model was developed and applied to simulate the absorption and polymerization taking place during holographic exposures of a multi-layer. The Beer-Lambert law was used to choose appropriate dye concentrations for each layer, with the objective of improving the resulting volume grating uniformity and thus diffraction characteristics. The predictions made, using previously estimated physical parameter values, indicated that improvements in the uniformity of the recorded modulation were possible. In this paper the results of experiments carried out to explore the validity of these predictions are presented. Improvements in material response are demonstrated experimentally, with improved grating diffraction (narrower angular selectivity) being observed for appropriately sensitized multi-layers.

Self-written waveguides in photopolymer.

Self-written waveguide (SWW) trajectories fabricated inside a dry photopolymer bulk material, acrylamide/polyvinyl alcohol (AA/PVA), are studied. Their production using both Gaussian and Laguerre-Gauss exposing (writing) light beams, output from optical fibers, is explored. The formation of the primary and secondary eyes is also discussed. Furthermore, the interactions that take place when two counterpropagating beams pass through the photopolymer material (both Gaussian and Laguerre-Gauss) are examined. In all cases experimental and theoretical results are presented. Good agreement between the predictions of the proposed model and experimental observations are demonstrated.