Structure-properties relationships in alkaline treated rice husk reinforced thermoplastic cassava starch biocomposites.

The study focuses on structure-properties relationships in thermoplastic cassava starch (TPS) based biocomposites comprising 5-20 wt% of untreated and treated rice husk (RH). Alkaline treatment with 11% w/v NaOH removed the hemicellulose layer of RH as confirmed by Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA), and resulted in a larger population of -OH groups exposing on the fibril surface. Consequently, the filler-matrix interactions between treated RH and TPS were enhanced, although Brunauer-Emmett-Teller (BET) surface area analysis indicated that the surface area of treated RH was not increased. Interestingly, the biocomposites contained 20 wt% treated RH showed substantially improved tensile strength by a factor of 220% compared to the neat TPS. The biocomposite at 15 wt% treated RH showed high water absorption. TPS with all treated RH contents showed high biodegradation rate, while the thermal stability of the TPS/treated RH biocomposites was slightly decreased. These novel composites showed promising properties for applications as absorbents.

Effective adsorption of methylene blue by biodegradable superabsorbent cassava starch-based hydrogel.

Superabsorbent hydrogels were synthesized from cassava starch (CS) and polyacrylamide (PAM) via radical polymerization. Scanning electron microscope revealed the porous structure of the hydrogels. Pore size was smaller at higher CS contents. Hydrogel containing 50 wt% CS (CS50) showed excellent water absorbency of >8000%, which was much greater than that of CS0 (pure PAM) hydrogel. This CS50 hydrogel removed >85% of methylene blue (MB) in <10 h with the greatest adsorption capacity of 2000 mg MB/g. The experimental results fitted the Freundlich and pseudo-second order models. After 4 cycles of use, the hydrogel could still remove >50% of MB in solution. Interestingly, the hydrogels were photodegradable and biodegradable. Buried in soil, the CS50 hydrogel was 80% degraded within 30 days whereas pure PAM was only 22% degraded.

Highly water resistant cassava starch/poly(vinyl alcohol) films.

Biodegradable films were prepared based on cassava starch (CS) and poly(vinyl alcohol) (PVA). To increase its tensile strength and flexibility, CS (20-60 wt%) was blended with PVA at various weight ratios (80-40 wt%). Triethylamine (TEA) was added as a homogeneous catalyst to increase intermolecular interaction and induce miscibility between CS and PVA. The crystallinity and hydrophobicity of blend films containing 20 wt% CS were promoted by the elimination of residual acetate groups in PVA. The number of hydrogen bonds in these blend films increased, which led to stronger interaction and more compact molecular packing between CS and PVA chains. The poor water resistance that limits the shelf-life and applications of CS blends was improved. The addition of TEA to blend films containing 20 wt% CS increased water resistance by 80% and tensile strength by as much as 440%. The development of greater structural integrity yielded ecologically sustainable, low-cost, biodegradable films with excellent physical and mechanical properties.

Solubilisation capacity of Brij surfactants.

The aim of this study was to investigate the potential of selected Brij non-ionic surfactants for enhancing the solubility of poorly water-soluble drugs. Griseofulvin was selected as a model drug candidate enabling comparisons to be made with the solubilisation capacities of other poly(ethylene oxide)-based copolymers. UV/Vis and (1)H NMR spectroscopies were used to quantify the enhancement of solubility of griseofulvin in 1 wt% aqueous micellar solutions of Brij 78 (C(18)H(37)E(20)), Brij 98 (C(18)H(35)E(20)) and Brij 700 (C(18)H(37)E(100)) (where E represents the OCH(2)CH(2) unit of the poly(ethylene oxide) chain) at 25, 37 and 40 °C. Solubilisation capacities (S(cp) expressed as mg griseofulvin per g Brij) were similar for Brij 78 and 98 (range 6-11 mg g(-1)) but lower for Brij 700 (3-4 mg g(-1)) as would be expected for the surfactant with the higher ethylene oxide content. The drug loading capacity of micelles of Brij 78 was higher than many di- and triblock copolymers with hydrophilic E-blocks specifically designed for enhancement of drug solubility.

Effect of water-soluble polymers, polyethylene glycol and poly(vinylpyrrolidone), on the gelation of aqueous micellar solutions of Pluronic copolymer F127.

The micellization of F127 (E(98)P(67)E(98)) in dilute aqueous solutions of polyethylene glycol (PEG6000 and PEG35000) and poly(vinylpyrrolidone) (PVP K30 and PVP K90) is studied. The average hydrodynamic radius (r(h,app)) obtained from the dynamic light scattering technique increased with increase in PEG concentration but decreased on addition of PVP, results which are consistent with interaction of the micelles with PEG and the formation of micelles clusters, but no such interaction occurs with PVP. Tube inversion was used to determine the onset of gelation. The critical concentration of F127 for gelation increased on addition of PEG and of PVP K30 but decreased on addition of PVP K90. Small-angle X-ray scattering (SAXS) was used to show that the 30 wt% F127 gel structure (fcc) was independent of polymer type and concentration, as was the d-spacing and so the micelle hard-sphere radius. The maximum elastic modulus (G(max)(')) of 30 wt% F127 decreased from its value for water alone as PEG was added, but was little changed by adding PVP. These results are consistent with the packed-micelles in the 30 wt% F127 gel being effectively isolated from the polymer solution on the microscale while, especially for the PEG, being mixed on the macroscale.

The effect of water-soluble polymers, PEG and PVP, on the solubilisation of griseofulvin in aqueous micellar solutions of Pluronic F127.

The purpose of this study was to investigate the possibility of enhancing the solubilisation capacity of micellar solutions of Pluronic F127 for the poorly water-soluble drug griseofulvin by co-formulating with a water-soluble polymer. The effect of the addition of the polyethylene glycols PEG6000 and 35000, and the poly(vinylpyrrolidone)s PVP K30 and K90, on the solubilisation capacity of 1wt% solutions of Pluronic F127 was related to the effect of these additives on particle size as determined by dynamic light scattering measurements. The addition of PEG35000 to 1wt% F127 solutions significantly increased the solubility capacity expressed in terms of unit weight of F127; PVP K90 had a smaller effect but no enhancement was noted following the addition of PEG6000 or PVP K30. Solubilisation enhancement was thought to be a consequence of the association of the polymers with the E-blocks of the micelle corona so providing an expanded region of reduced polarity for drug solubilisation.

The effect of polymeric additives on the solubilisation of a poorly-soluble drug in micellar solutions of Pluronic F127.

The solubilisation of griseofulvin in 1wt% aqueous micellar solutions of Pluronic F127 at 37°C has been modified by adding polyethylene glycol PEG 35000 or poly(vinylpyrrolidone) PVP K30. The solubilisation capacity expressed in terms of unit weight of F127 is increased by the addition of 0.5wt% PEG 35000 to a value approaching double that of a 2.5wt% solution of F127 alone, but there is no advantage in adding 0.5wt% PVP K30.

The effect of n-, s- and t-butanol on the micellization and gelation of Pluronic P123 in aqueous solution.

In dilute aqueous solution unimers of copolymer P123 (E(21)P(67)E(21)) associate to form micelles, and in more concentrated solution micelles pack to form high-modulus gels. We are interested in the use of the system as a templating agent in the synthesis of mesoporous materials, and the possibility of determining gel structure, hence mesoporosity, by use of n-, s- or t-butanol. Dynamic light scattering from clear dilute solutions has been used to confirm micellization, visual observation of mobility (tube inversion) to detect gel formation in concentrated solutions, oscillatory rheometry to confirm gel formation and provide values of elastic moduli over a wide temperature range, and small-angle X-ray scattering to determine gel structure. As expected, clear cubic gels (fcc) formed at moderate concentrations and temperatures, e.g. 30 wt.% P123, 20°C, and clear hexagonal gels at higher concentrations and temperatures. The transition on heating from cubic to hexagonal gel involved an intermediate turbid phase in which cubic and hex structures coexisted. Considering cubic gels of 35 wt.% P123 in 5 wt.% butanol/water, those in n-butanol/water had the lowest critical temperatures for gel formation and the highest maximum values for the dynamic elastic modulus (G') of the gels, a result consistent with n-butanol/water being the poorest solvent for P123.

Effect of ethanol on the gelation of aqueous solutions of Pluronic F127.

In dilute aqueous solution unimers of copolymer F127 (E(98)P(67)E(98)) associate to form micelles, and in more concentrated solution micelles pack to form high-modulus gels. Cosolvents are known to affect these processes, and ethanol/water mixtures have been of particular interest. Dynamic light scattering from dilute solutions was used to confirm micellization, but major attention was directed towards the gels. Visual observation of mobility (tube inversion) was used to detect gel formation, oscillatory rheometry to confirm gel formation and provide values of the elastic moduli over a wide temperature range, and small-angle X-ray scattering to determine gel structure. The solvents were limited to 10, 20 and 30 wt.% ethanol/water. Critical concentrations for gel formation were similar for 10 and 20 wt.% ethanol/water but were significantly increased for 30 wt.% ethanol/water, e.g. at T=45 degrees C from c approximately 15 wt.% to c approximately 28 wt.%. The elastic moduli reached maximum values at T approximately 50 degrees C: e.g. G' approximately 25 kPa for 25 wt.% F127 in 10 and 20 wt.% ethanol/water and a similar value for 30 wt.% F127 in 30 wt.% ethanol/water. Hard gels of 30 and 35 wt.% F127 in ethanol/water at 25 and 40 degrees C had the body-centered cubic (bcc) structure.

Aqueous gels of mixtures of ionic surfactant SDS with pluronic copolymers P123 or F127.

Gel diagrams based on tube inversion and oscillatory rheometry are reported for Pluronic copolymers F127 (E(98)P(67)E(98)) and P123 (E(21)P(67)E(21)) in mixtures with anionic surfactant sodium dodecyl sulfate (SDS). Total concentrations (c, SDS+copolymer) were as high as 50 wt % with mole ratios SDS/copolymer (mr) in the ranges 1-5 (F127) and 1-7 (P123). Temperatures were as high as 90 degrees C. Determination of the temperature dependences of the dynamic moduli served to confirm the gel boundaries from tube inversion and to reveal the high elastic moduli of the gels, e.g., compared at comparable positions in the gel phase, a 50 wt % SDS/P123 with mr = 7 had G' three times that of a corresponding gel of P123 alone. Small-angle X-ray scattering (SAXS) was used to show that the structures of all the SDS/F127 gels were bcc and that the structures of the SDS/P123 gels with mr = 1 were either fcc (c = 30 wt %) or hex (c = 40 wt %). Assignment of structures to SDS/P123 gels with values of mr in the range 3-7 was more difficult, as high-order scattering peaks could be very weak, and at the higher values of c and mr, the SAXS peaks included multiple reflections.

Interactions of an anionic surfactant with poly(oxyalkylene) copolymers in aqueous solution.

The interactions of sodium dodecyl sulfate (SDS) with poly(ethylene oxide)/poly(alkylene oxide) (E/A) block copolymers are explored in this study. With respect to the specific compositional characteristics of the copolymer, introduction of SDS can induce fundamentally different effects to the self-assembly behavior of E/A copolymer solutions. In the case of the E(18)B(10)-SDS system (E = poly(ethylene oxide) and B = poly(butylene oxide)) development of large surfactant-polymer aggregates was observed. In the case of B(20)E(610)-SDS, B(12)E(227)B(12)-SDS, E(40)B(10)E(40)-SDS, E(19)P(43)E(19)-SDS (P = poly(propylene oxide)), the formation of smaller particles compared to pure polymeric micelles points to micellar suppression induced by the ionic surfactant. This effect can be ascribed to a physical binding between the hydrophobic block of unassociated macromolecules and the non-polar tail of the surfactant. Analysis of critical micelle concentrations (cmc(*)) of polymer-surfactant aqueous solutions within the framework of regular solution theory for binary surfactants revealed negative deviations from ideal behavior for E(40)B(10)E(40)-SDS and E(19)P(43)E(19)-SDS, but positive deviations for E(18)B(10)-SDS. Ultrasonic studies performed for the E(19)P(43)E(19)-SDS system enabled the identification of three distinct regions, corresponding to three main steps of the complexation; SDS absorption to the hydrophobic backbone of polymer, development of polymer-surfactant complexes and gradual breakdown of the mixed aggregates.

Effect of ethanol on the micellization and gelation of pluronic p123.

In certain applications copolymer P123 (E21P67E21) is dissolved in water-ethanol mixtures, initially to form micellar solutions and eventually to gel. For P123 in 10, 20, and 30 wt % aqueous ethanol we used dynamic light scattering from dilute solutions to confirm micellization, oscillatory rheometry, and visual observation of mobility (tube inversion) to determine gel formation in concentrated solutions and small-angle X-ray scattering (SAXS) to determine gel structure. Except for solutions in 30 wt % aqueous ethanol, a clear-turbid transition was encountered on heating dilute and concentrated micellar solutions alike, and as for solutions in water alone (Chaibundit et al. Langmuir 2007, 23, 9229) this could be ascribed to formation of wormlike micelles. Dense clouding, typical of phase separation, was observed at higher temperatures. Regions of isotropic and birefringent gel were defined for concentrated solutions and shown (by SAXS) to have cubic (fcc and hcp) and hexagonal structures, consistent with packed spherical and elongated micelles, respectively. The cubic gels (0, 10, and 20 wt % ethanol) were clear, while the hex gels were either turbid (0 and 10 wt % ethanol), turbid enclosing a clear region (20 wt % ethanol), or entirely clear (30 wt % ethanol). The SAXS profile was unchanged between turbid and clear regions of the 20 wt % ethanol gel. Temperature scans of dynamic moduli showed (as expected) a clear distinction between high-modulus cubic gels (G'max approximately 20-30 kPa) and lower modulus hex gels (G'max<10 kPa).

Solubilisation of drugs in worm-like micelles of block copolymers of ethylene oxide and 1,2-butylene oxide in aqueous solution.

Ethylene oxide and 1,2-butylene oxide were sequentially polymerised to form the diblock copolymer E13B10 (E=oxyethylene, B=oxybutylene, subscripts denote number-average block lengths in repeat units). Dynamic and static light scattering over the temperature range 10-30 degrees C demonstrated a transition from compact (spheroidal) micelles to larger, more elongated (worm-like) micelles with temperature increase above a critical onset temperature of about 20 degrees C. Determination of the solubilisation capacity for griseofulvin, carbamazepine and spironolactone of dilute micellar solutions of this copolymer, together with those of E11B8 and E17B12 block copolymers (which also show the sphere-to-worm transition), allowed investigation of the influence on solubilisation characteristics of hydrophobic block length and temperature. The extent of solubilisation at 25 degrees C of the poorly water-soluble drug spironolactone increased linearly with increase of hydrophobic block length, attributable to a concomitant increase in the proportion of worm-like micelles in solution.

Block copolymers for drug solubilisation: relative hydrophobicities of polyether and polyester micelle-core-forming blocks.

Published values of the critical micelle concentration are tabulated for diblock copolymers E(m)P(n), E(m)B(n), E(m)S(n), E(m)L(n), E(m)VL(n) and E(m)CL(n), where E denotes a chain unit derived from ethylene oxide, P from propylene oxide, B from 1,2-butylene oxide, S from styrene oxide, L from dl-lactide, VL from gamma-valerolactone and CL from epsilon-caprolactone, and the subscripts denote average chain lengths. Noting that log(cmc/moldm(-3) is proportional to the standard Gibbs energy of micellisation, the dependence of this quantity on hydrophobic block length (n) is explored for a given E-block length. Superposition of data allows ranking of the hydrophobicities of the chain units. The ratios relative to the least hydrophobic unit are: P : L : B : VL : S : CL = 1 : 4 : 6 : 10 : 12 : 12 Transitions in the slope of log(cmc) versus n are assigned to changes in the unimer-micelle equilibrium and related to the formation of unimolecular micelles and, at high values of n, to the completion of that process. The formation transition is seen in the plots for all the copolymers except the least hydrophobic, E(m)P(n). The completion transition is seen in the plots for E(m)CL(n) and E(m)L(n) copolymers, as these alone include results for copolymers with very lengthy hydrophobic blocks.

Micellization and gelation of mixed copolymers P123 and F127 in aqueous solution.

The micellization in dilute aqueous solution of Pluronic copolymers P123 (E21P67E21) and F127 (E98P67E98) and mixtures of the two was investigated using static and dynamic light scattering. Gelation of concentrated solutions of the two copolymers and their mixtures was studied using tube inversion and oscillatory rheometry. The two copolymers comicellized to give micelles with narrow size distributions. Clouding temperatures and critical micelle temperatures decreased as the proportion of P123 in the mixture was increased. Micelle association numbers of the mixed micelles lay between the values found for micelles of P123 and F127 alone, whereas micelle radii passed through maximum values in the range 0-50 wt % P123. As judged by the ratio of the thermodynamic to the hydrodynamic radius, the micelle interaction potential changes gradually from soft to hard as the proportion of P123 in the mixture is increased. Regions of cubic and hexagonal (birefringent) gel were defined for concentrated solutions. The high-temperature boundary of the 30 wt % cubic gel decreased monotonically from 90 to 43 degrees C as the proportion of P123 in the mixture was increased from 0 to 100 wt %, whereas the low-temperature boundary was essentially constant at 15 +/- 3 degrees C. Increasing the proportion of P123 in the mixture at 25 degrees C increased the concentration at which the cubic gel was first formed and decreased the concentration at which the hexagonal gel was first formed.

Association behavior of mixed triblock copoly(oxyalkylene)s (type EBE and ESE) in aqueous solution.

The micellization of binary mixtures of water-soluble block copolymers E(m)B(n)E(m) and E(m)S(n)E(m) in dilute solution was investigated by light-scattering methods. We use the notation E, B, and S to denote chain units derived, respectively, from ethylene oxide, butylene oxide, and styrene oxide and the subscripts to denote number-average chain lengths in chain units. Two distinct distributions of micelles were formed in solutions of a 50:50 wt % mixture of copolymers E64B20E64 and E137S18E137, which had hydrophobic blocks of similar length but very different hydrophobicity. One distribution of micelles was formed in solutions of a mixture (50:50 wt %) of copolymers E135B20E135 and E82S9E82, which had hydrophobic blocks of different length but similar hydrophobicity. In this case, the properties of the micelles formed in solutions of the mixture were very similar to those of micelles of E82S9E82 alone. This result extended to concentrated solutions, because the hard-gel boundary for the mixture proved to be very similar to that of solutions of E82S9E82 alone.

Solubilisation in aqueous micellar solutions of block copoly(oxyalkylene)s.

The solubilisation capacities of micellar solutions of diblock and triblock copolymers composed of hydrophilic poly(ethylene oxide) and hydrophobic poly(styrene oxide) have been compared using the poorly water-soluble drug griseofulvin as a model solubilisate. Our results showed an increase of solubilisation capacity (expressed as mg griseofulvin per gram of hydrophobic block) with temperature and, for spherical micelles, with core volume before reaching limiting values. A change of micelle shape from spherical to cylindrical (or worm-like) resulting from an increase in micelle aggregation number was accompanied by a further enhancement of solubilisation capacity. Comparison with the solubilisation of the same drug in micellar solutions of block copolymers of poly(ethylene oxide) and poly(1,2-butylene oxide) showed that the solubilisation capacity of a poly(styrene oxide) block was approximately four times that of a poly(1,2-butylene oxide) block for spherical micelles. Solubilisation capacity at 25 degrees C was approximately doubled when griseofulvin was incorporated into a copolymer melt and micelles initially formed from the drug-loaded melt at 65 degrees C rather than by loading the drug into pre-micellised solution at 25 degrees C in the usual manner.

Association properties of diblock copolymer of ethylene oxide and 1,2-butylene oxide: E17B12 in aqueous solution.

Copolymer E(17)B(12) (E denotes OCH(2)CH(2), B denotes OCH(2)CH(C(2)H(5)), and the subscripts denote number-average chain lengths) was prepared by sequential oxyanionic polymerization and characterized by GPC (for distribution width) and NMR spectroscopy (for absolute composition and chain length). Dynamic and static light scattering and rheometry were used to characterize micelles in dilute solution and demonstrate the formation of compact micelles at low temperatures and of elongated micelles at higher temperatures, the latter being accompanied by turbidity of the solution. Rheological methods applied across a range of concentrations and temperatures served to demonstrate the formation of worm-like micelles. Gels based on entangled worm-like micelles (some of them turbid) and on packed compact micelles were identified and their properties were explored.