Modular time division multiplexer: Efficient simultaneous characterization of fast and slow transients in multiple samples.

A modular time division multiplexer (MTDM) device is introduced to enable parallel measurement of multiple samples with both fast and slow decay transients spanning from millisecond to month-long time scales. This is achieved by dedicating a single high-speed measurement instrument for rapid data collection at the start of a transient, and by multiplexing a second low-speed measurement instrument for slow data collection of several samples in parallel for the later transients. The MTDM is a high-level design concept that can in principle measure an arbitrary number of samples, and the low cost implementation here allows up to 16 samples to be measured in parallel over several months, reducing the total ensemble measurement duration and equipment usage by as much as an order of magnitude without sacrificing fidelity. The MTDM was successfully demonstrated by simultaneously measuring the photoconductivity of three amorphous indium-gallium-zinc-oxide thin films with 20 ms data resolution for fast transients and an uninterrupted parallel run time of over 20 days. The MTDM has potential applications in many areas of research that manifest response times spanning many orders of magnitude, such as photovoltaics, rechargeable batteries, amorphous semiconductors such as silicon and amorphous indium-gallium-zinc-oxide.

Materials, interfaces, and photon confinement in dye-sensitized solar cells.

A series of experiments have been carried out to study the effects of materials quality, surface and interfacial modification, and photon confinement on standard dye-sensitized solar cells. For these studies, both physical and optical characterization of the materials has been performed in detail. In addition, DC and AC impedance measurements along with kinetic charge-transport modeling of experimental results have yielded information on how to systematically optimize the cell efficiency. The same kinetic model has been used to interpret the results of a series of experiments on interfacial modification studies using fluorine etching in combination with TiCl(4) surface treatment. By using specially designed photonic crystals to confine the photons in the cells, it is shown that the best cell efficiency can be further increased by about 13%.

One-dimensional long-range plasmonic-photonic structures.

We have fabricated line gratings from periodically etched fused silica on which a thin silver film is deposited that is in turn covered with a silica index-matched fluid. This dielectrically symmetric geometry supports an independent long-range surface plasmon-polariton (LRSPP) and a short-range surface plasmon polariton, and the associated plasmonic band structure has been probed. Coupling to external light is achieved via the patterned grating, and an ultrasharp LRSPP linewidth of 4 nm is observed. The experimental results are compared with finite-difference time-domain simulations.

Synthesis and characterization of iron silicon boron (Fe5Si2B) and iron boride (Fe3B) nanowires.

Single-crystal iron silicon boron (Fe(5)Si(2)B) and iron boride (Fe(3)B) nanowires were synthesized by a chemical vapor deposition (CVD) method on either silicon dioxide (SiO(2)) on silicon (Si) or Si substrates without introducing any catalysts. FeI(2) and BI(3) were used as precursors. The typical size of the nanowires is about 5-50 nm in width and 1-20 mum in length. Different kinds of Fe-Si-B and Fe-B structures were synthesized by adjusting the ratio of FeI(2) vapor to BI(3) vapor. Single-crystal Fe(5)Si(2)B nanowires formed when the FeI(2) sublimator temperature was kept in the range of 540-570 degrees C. If the FeI(2) sublimator temperature was adjusted in the range of 430-470 degrees C, single-crystal Fe(3)B nanowires were produced. Fe(3)B nanowires grow from polycrystalline Fe(5)SiB(2) particles, while Fe(5)Si(2)B nanowires grow out of the Fe(5)Si(2)B layers, which are attached to triangle shaped FeSi particles. Both the ratio of FeI(2) vapor to BI(3) vapor and the formation of the particles (Fe(5)SiB(2) particles for the growth of Fe(3)B nanowires, FeSi particles for the growth of Fe(5)Si(2)B nanowires) are critical for the growth of Fe(3)B and Fe(5)Si(2)B nanowires. The correct FeI(2) vapor to BI(3) vapor ratio assures the desired phase form, while the particles provide preferential sites for adsorption and nucleation of Fe(3)B or Fe(5)Si(2)B molecules. Fe(3)B or Fe(5)Si(2)B nanowires grow due to the preferred growth direction of <110>.

Self-optimization of optical confinement in an ultraviolet photonic crystal slab laser.

We studied numerically and experimentally the effects of structural disorder on the performance of ultraviolet photonic crystal slab lasers. Optical gain selectively amplifies the high-quality modes of the passive system. For these modes, the in-plane and out-of-plane leakage rates may be automatically balanced in the presence of disorder. The spontaneous optimization of in-plane and out-of-plane confinement of light in a photonic crystal slab may lead to a reduction of the lasing threshold.