Solar photothermochemical alkane reverse combustion.

A one-step, gas-phase photothermocatalytic process for the synthesis of hydrocarbons, including liquid alkanes, aromatics, and oxygenates, with carbon numbers (Cn) up to C13, from CO2 and water is demonstrated in a flow photoreactor operating at elevated temperatures (180-200 °C) and pressures (1-6 bar) using a 5% cobalt on TiO2 catalyst and under UV irradiation. A parametric study of temperature, pressure, and partial pressure ratio revealed that temperatures in excess of 160 °C are needed to obtain the higher Cn products in quantity and that the product distribution shifts toward higher Cn products with increasing pressure. In the best run so far, over 13% by mass of the products were C5+ hydrocarbons and some of these, i.e., octane, are drop-in replacements for existing liquid hydrocarbons fuels. Dioxygen was detected in yields ranging between 64% and 150%. In principle, this tandem photochemical-thermochemical process, fitted with a photocatalyst better matched to the solar spectrum, could provide a cheap and direct method to produce liquid hydrocarbons from CO2 and water via a solar process which uses concentrated sunlight for both photochemical excitation to generate high-energy intermediates and heat to drive important thermochemical carbon-chain-forming reactions.

Tailoring copper oxide semiconductor nanorod arrays for photoelectrochemical reduction of carbon dioxide to methanol.

Solar photoelectrochemical reduction of carbon dioxide to methanol in aqueous media was driven on hybrid CuO/Cu2O semiconductor nanorod arrays for the first time. A two-step synthesis was designed and demonstrated for the preparation of these hybrid copper oxide one-dimensional nanostructures on copper substrates. The first step consisted in the growth of CuO nanorods by thermal oxidation of a copper foil at 400 °C. In the second step, controlled electrodeposition of p-type Cu2O crystallites on the CuO walls was performed. The resulting nanorod morphology with controllable wall thickness by adjusting the Cu2O electrodeposition time as well as their surface/bulk chemical composition were probed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. Photoelectrosynthesis of methanol from carbon dioxide was demonstrated at -0.2 V vs SHE under simulated AM1.5 solar irradiation on optimized hybrid CuO/Cu2O nanorod electrodes and without assistance of any homogeneous catalyst (such as pyridine or imidazole) in the electrolyte. The hybrid composition, ensuring double pathway for photoelectron injection to CO2, along with high surface area were found to be crucial for efficient performance in methanol generation under solar illumination. Methanol formation, tracked by gas chromatography/mass spectrometry, indicated Faradaic efficiencies of ~95%.

Efficient solar photoelectrosynthesis of methanol from carbon dioxide using hybrid CuO-Cu2O semiconductor nanorod arrays.

Solar photoelectrosynthesis of methanol was driven on hybrid CuO-Cu(2)O semiconductor nanorod arrays for the first time at potentials ~800 mV below the thermodynamic threshold value and at Faradaic efficiencies up to ~95%. The CuO-Cu(2)O nanorod arrays were prepared on Cu substrates by a two-step approach consisting of the initial thermal growth of CuO nanorods followed by controlled electrodeposition of p-type Cu(2)O crystallites on their walls. No homogeneous co-catalysts (such as pyridine, imidazole or metal cyclam complexes) were used contrasting with earlier studies on this topic using p-type semiconductor photocathodes. The roles of the core-shell nanorod electrode geometry and the copper oxide composition were established by varying the time of electrodeposition of the Cu(2)O phase on the CuO nanorod core surface.

Photocatalytic generation of syngas using combustion-synthesized silver bismuth tungstate.

Silver bismuth tungstate (AgBiW(2)O(8)) nanoparticles were prepared for the first time by solution combustion synthesis by using the corresponding metal nitrates as the precursor and urea as the fuel. These nanoparticles were subsequently modified with Pt catalyst islands using a photocatalytic procedure and used for the photogeneration of syngas (CO+H(2)). Formic acid was used for this purpose for the in situ generation of CO(2) and its subsequent reduction to CO. In the absence of Pt modification, H(2) was not obtained in the gas products evolved. These results were compared with those obtained with acetic acid in place of formic acid. The combustion process was simulated by thermogravimetry and the synthesized powder was characterized using transmission electron microscopy, diffuse reflectance UV/Vis spectroscopy, X-ray diffraction, surface area measurements, and X-ray photoelectron spectroscopy. Tauc plots derived from the diffuse reflectance data yielded an optical band gap of 2.74 eV. The photocatalytic activity of these nanoparticles was superior to a sample prepared by solid-state synthesis. Mechanistic aspects are finally presented, as are structural models and electronic calculations, using density functional theory (DFT).

Electrochemical grafting of poly(3,4-ethylenedioxythiophene) into a titanium dioxide nanotube host network.

This study focuses on electrodeposition for infiltrating in situ a conducting polymer such as poly(3,4-ethylenedioxythiophene) (PEDOT) into a host titanium dioxide (TiO(2)) nanotube array (NTA) framework. The TiO(2) NTA was electrosynthesized on titanium foil in turn by anodization in a fluoride-containing medium. The PEDOT layer was electrografted into the TiO(2) NTA framework using a two-step potentiostatic growth protocol in acetonitrile containing supporting electrolyte. The nanoscopic features of oligomer/polymer infiltration and deposition in the NTA interstitial voids were monitored by field-emission scanning electron microscopy. Systematic changes in the nanotube inner diameter and the wall thickness afforded insights into the evolution of the TiO(2)NTA/PEDOT hybrid assembly. This assembly was subsequently characterized by UV-visible diffuse reflectance, cyclic voltammetry, and photoelectrochemical measurements. These data serve as a prelude to further use of these hybrids in heterojunction solar cells.

Formation and characterization of self-organized TiO2 nanotube arrays by pulse anodization.

This paper describes TiO2 nanotube arrays prepared by anodic oxidation of Ti substrates using pulse voltage waveforms. Voltages were pulsed between 20 and -4 V or between 20 and 0 V with varying durations from 2 to 16 s at the lower limit of the pulse waveform. Ammonium fluoride or sodium fluoride (and mixtures of both) was used as the electrolyte with or without added medium modifier (glycerol, ethylene glycol, or poly (ethylene glycol) (PEG 400)) in these experiments. The pulse waveform was optimized to electrochemically grow TiO2 nanotubes and chemically etch their walls during its cathodic current flow regime. The resultant TiO2 nanotube arrays showed a higher quality of nanotube array morphology and photoresponse than samples grown via the conventional continuous anodization method. Films grown with a 20 V/-4 V pulse sequence and pulse duration of 2 s at its negative voltage limit afforded a superior photoresponse compared to other pulse durations. Specifically, the negative voltage limit of the pulse (-4 V) and its duration promote the adsorption of NH4+ species that in turn inhibits chemical attack of the growing oxide nanoarchitecture by the electrolyte F- species. The longer the period of the pulse at the negative voltage limit, the thicker the nanotube walls and the shorter the nanotube length. At variance, with 0 V as the low voltage limit, the longer the pulse duration, the thinner the oxide nanotube wall, suggesting that chemical attack by fluoride ions is not counterbalanced by NH3/NH4+ species adsorption, unlike the interfacial situation prevailing at -4 V. Finally, the results from this study provide useful evidence in support of existing mechanistic models for anodic growth and self-assembly of oxide nanotube arrays on the parent metal surface.