Effectiveness of N95 Mask in Preventing COVID-19 Transmission.

N95 mask has emerged as a potential measure to mitigate the airborne transmission of respiratory disease such as COVID-19. Herein, we experimentally investigated the impact and interaction of pure water droplets as surrogate to respiratory droplets with the different layers of a commercially available N95 mask to demonstrate the penetration and passage-capability of respiratory fluids through the different layers. The penetration of an impacting droplet through the mask layers was characterized by elucidating the ejection of secondary droplets from the rear-side surface of the target mask material. In addition, the passage of respiratory fluids through the mask layers was characterized by capillary imbibition of the droplet liquid through the pores, as a function of wettability of the mask material. Droplet impact at Weber numbers We = 208 and 416 has been considered in the present study; the chosen We range corresponds to that of cough droplets realized in real respiratory events. Each layer of the N95 mask is hydrophobic that prevents capillary imbibition through the pores: a sessile droplet placed over the surface exhibits classical diffusion-limited evaporation. Droplet impact experiments on N95 mask layer surfaces reveal that a single layer allows liquid penetration at We = 416; while a combination of five layers, as is the case of a commercially available N95 mask, blocks the penetration completely, consistent with the widely known effectiveness of N95 masks. Herein, we devote special attention to compare the so-obtained efficiency of N95 masks to that of a recently designed two-layer cloth mask containing an intermediate High-Efficiency Particulate Air (HEPA) filter layer (Narayan et al. in Phys Fluids 34:061703, 2022). We conclusively show that the performance of the designed cloth mask is identical to that of a commercially available N95 mask. The assessment of mask effectiveness further includes examination of breathability and comfort by means of passage of air through them. A comparative study has been presented herein for a clear demonstration of effectiveness of different masks in preventing air-borne transmission of COVID-19.

Size-Dependent Dried Colloidal Deposit and Particle Sorting via Saturated Alcohol Vapor-Mediated Sessile Droplet Spreading.

We experimentally and theoretically investigate a distinct problem of spreading, evaporation, and the associated dried deposits of a colloidal particle-laden aqueous sessile droplet on a surface in a saturated alcohol vapor environment. In particular, the effect of particle size on monodispersed suspensions and efficient self-sorting of bidispersed particles have been investigated. The alcohol vapor diffuses toward the droplet's curved liquid-vapor interface from the far field. The incoming vapor mass flux profile assumes a nonuniform pattern across the interface. The alcohol vapor molecules are adsorbed at the liquid-vapor interface, which eventually leads to absorption into the droplet's liquid phase due to the miscibility. This phenomenon triggers a liquid-vapor interfacial tension gradient and causes a reduction in the global surface tension of the droplet. This results in a solutal Marangoni flow recirculation and spontaneous droplet spreading. The interplay between these phenomena gives rise to a complex internal fluid flow within the droplet, resulting in a significantly modified and strongly particle-size-dependent dried colloidal deposit. While the smaller particles form a multiple ring pattern, larger particles form a single ring, and additional "patchwise" deposits emerge. High-speed visualization of the internal liquid-flow revealed that initially, a ring forms at the first location of the contact line. Concurrently, the Marangoni flow recirculation drives a collection of particles at the liquid-vapor interface to form clusters. Thereafter, as the droplet spreads, the smaller particles in the cluster exhibit a "jetlike" outward flow, forming multiple ring patterns. In contrast, the larger particles tend to coalesce together in the cluster, forming the "patchwise" deposits. The widely different response of the different-sized particles to the internal fluid flow enables an efficient sorting of the smaller particles at the contact line from bidispersed suspensions. We corroborate the measurements with theoretical and numerical models wherever possible.

Evaluating a transparent coating on a face shield for repelling airborne respiratory droplets.

A face shield is an important personal protective equipment to avoid the airborne transmission of COVID-19. We assess a transparent coating on a face shield that repels airborne respiratory droplets to mitigate the spread of COVID-19. The surface of the available face shield is hydrophilic and exhibits high contact angle hysteresis. The impacting droplets stick on it, resulting in an enhanced risk of fomite transmission of the disease. Further, it may get wetted in the rain, and moisture may condense on it in the presence of large humidity, which may blur the user's vision. Therefore, the present study aims to improve the effectiveness of a face shield. Our measurements demonstrate that the face shield, coated by silica nanoparticles solution, becomes superhydrophobic and results in a nominal hysteresis to the underlying surface. We employ high-speed visualization to record the impact dynamics of microliter droplets with a varying impact velocity and angle of attack on coated and non-coated surfaces. While the droplet on non-coated surface sticks to it, in the coated surface the droplets bounce off and roll down the surface, for a wide range of Weber number. We develop an analytical model and present a regime map of the bouncing and non-bouncing events, parametrized with respect to the wettability, hysteresis of the surface, and the Weber number. The present measurements provide the fundamental insights of the bouncing droplet impact dynamics and show that the coated face shield is potentially more effective in suppressing the airborne and fomite transmission.

How coronavirus survives for hours in aerosols.

COVID (CoronaVirus Disease)-19, caused by severe acute respiratory syndrome-CoronaVirus-2 (SARS-CoV-2) virus, predominantly transmits via airborne route, as highlighted by recent studies. Furthermore, recently published titer measurements of SARS-CoV-2 in aerosols have disclosed that the coronavirus can survive for hours. A consolidated knowledge on the physical mechanism and governing rules behind the significantly long survival of coronavirus in aerosols is lacking, which is the subject of the present investigation. We model the evaporation of aerosolized droplets of diameter ≤ 5 µ m. The conventional diffusion-limited evaporation is not valid to model the evaporation of small size (µm-nm) droplets since it predicts drying time on the order of milliseconds. Also, the sedimentation timescale of desiccated droplets is on the order of days and overpredicts the virus survival time; hence, it does not corroborate with the above-mentioned titer-decay timescale. We attribute the virus survival timescale to the fact that the drying of small ( ∼ µ m-nm) droplets is governed, in principle, by the excess internal pressure within the droplet, which stems from the disjoining pressure due to the cohesive intermolecular interaction between the liquid molecules and the Laplace-pressure. The model predictions for the temporal reduction in the aerosolized droplet number density agree well with the temporal decay of virus titer. The findings, therefore, provide insight on the survival of coronavirus in aerosols, which is particularly important to mitigate the spread of COVID-19 from indoors.

Designing antiviral surfaces to suppress the spread of COVID-19.

Surface engineering is an emerging technology to design antiviral surfaces, especially in the wake of COVID-19 pandemic. However, there is yet no general understanding of the rules and optimized conditions governing the virucidal properties of engineered surfaces. The understanding is crucial for designing antiviral surfaces. Previous studies reported that the drying time of a residual thin-film after the evaporation of a bulk respiratory droplet on a smooth surface correlates with the coronavirus survival time. Recently, we [Chatterjee et al., Phys. Fluids. 33, 021701 (2021)] showed that the evaporation is much faster on porous than impermeable surfaces, making the porous surfaces lesser susceptible to virus survival. The faster evaporation on porous surfaces was attributed to an enhanced disjoining pressure within the thin-film due the presence of horizontally oriented fibers and void spaces. Motivated by this, we explore herein the disjoining pressure-driven thin-film evaporation mechanism and thereby the virucidal properties of engineered surfaces with varied wettability and texture. A generic model is developed which agrees qualitatively well with the previous virus titer measurements on nanostructured surfaces. Thereafter, we design model surfaces and report the optimized conditions for roughness and wettability to achieve the most prominent virucidal effect. We have deciphered that the optimized thin-film lifetime can be gained by tailoring wettability and roughness, irrespective of the nature of texture geometry. The present study expands the applicability of the process and demonstrates ways to design antiviral surfaces, thereby aiding to mitigate the spread of COVID-19.

Why coronavirus survives longer on impermeable than porous surfaces.

Previous studies reported that the drying time of a respiratory droplet on an impermeable surface along with a residual film left on it is correlated with the coronavirus survival time. Notably, earlier virus titer measurements revealed that the survival time is surprisingly less on porous surfaces such as paper and cloth than that on impermeable surfaces. Previous studies could not capture this distinct aspect of the porous media. We demonstrate how the mass loss of a respiratory droplet and the evaporation mechanism of a thin liquid film are modified for the porous media, which leads to a faster decay of the coronavirus on such media. While diffusion-limited evaporation governs the mass loss from the bulk droplet for the impermeable surface, a much faster capillary imbibition process dominates the mass loss for the porous material. After the bulk droplet vanishes, a thin liquid film remaining on the exposed solid area serves as a medium for the virus survival. However, the thin film evaporates much faster on porous surfaces than on impermeable surfaces. The aforesaid faster film evaporation is attributed to droplet spreading due to the capillary action between the contact line and fibers present on the porous surface and the modified effective wetted area due to the voids of porous materials, which leads to an enhanced disjoining pressure within the film, thereby accelerating the film evaporation. Therefore, the porous materials are less susceptible to virus survival. The findings have been compared with the previous virus titer measurements.

Evaporation of Initially Heated Sessile Droplets and the Resultant Dried Colloidal Deposits on Substrates Held at Ambient Temperature.

The present study experimentally and numerically investigates the evaporation and resultant patterns of dried deposits of aqueous colloidal sessile droplets when the droplets are initially elevated to a high temperature before being placed on a substrate held at ambient temperature. The system is then released for natural evaporation without applying any external perturbation. Infrared thermography and optical profilometry are used as essential tools for interfacial temperature measurements and quantification of coffee-ring dimensions, respectively. Initially, a significant temperature gradient exists along the liquid-gas interface as soon as the droplet is deposited on the substrate, which triggers a Marangoni stress-induced recirculation flow directed from the top of the droplet toward the contact line along the liquid-gas interface. Thus, the flow is in the reverse direction to that seen in the conventional substrate heating case. Interestingly, this temperature gradient decays rapidly within the first 10% of the total evaporation time and the droplet-substrate system reaches thermal equilibrium with ambient thereafter. Despite the fast decay of the temperature gradient, the coffee-ring dimensions significantly diminish, leading to an inner deposit. A reduction of 50-70% in the coffee-ring dimensions is recorded by elevating the initial droplet temperature from 25 to 75 °C for suspended particle concentration varying between 0.05 and 1.0% v/v. This suppression of the coffee-ring effect is attributed to the fact that the initial Marangoni stress-induced recirculation flow continues until the last stage of evaporation, even after the interfacial temperature gradient vanishes. This is essentially a consequence of liquid inertia. Finally, a finite-element-based two-dimensional modeling in axisymmetric geometry is found to capture the measurements with reasonable fidelity and the hypothesis considered in the present study corroborates well with a first approximation qualitative scaling analysis. Overall, together with a new experimental condition, the present investigation discloses a distinct nature of Marangoni stress-induced flow in a drying droplet and its role in influencing the associated colloidal deposits, which was not explored previously. The insights gained from this study are useful to advance technical applications such as spray cooling, inkjet printing, bioassays, etc.