RESUMO
The study of metals and alloys containing helium has garnered significant attention within the nuclear energy community. However, there is limited research on the mechanical behavior of bulk alloys implanted with helium. This study investigates the mechanical properties of several Al-Boron alloys implanted with helium using controlled manipulation of helium doses via boron content under a consistent neutron dose. Results show that HemVn may contribute to strength by approximately 8.4-15 MPa and 16.8-23 MPa for helium doses 3.08 × 1019/cm3 and 6.84 × 1019/cm3, respectively, while lattice damages due to neutron-aluminum reaction contribute to strength by 24â¼27 MPa. Subsequent annealing leads to the formation of helium bubbles, resulting in a slightly higher strengthening effect compared to HemVn. Additionally, the work hardening behavior of the alloys can be explained by the Voce model, drawing inspiration from the resemblance between helium bubbles and nanoprecipitates in 7xxx alloys. These findings provide insights to the nuclear energy community.
RESUMO
In the process of high temperature service, the mechanical properties of cutting tools decrease sharply due to the peeling of the protective coating. However, the mechanism of such coating failure remains obscure due to the complicated interaction between atomic structure, temperature, and stress. This dynamic evolution nature demands both large system sizes and accurate description on the atomic scale, raising challenges for existing atomic scale calculation methods. Here, we developed a deep neural network (DNN) potential for Ti-N binary systems based on first-principles study datasets to achieve quantum-accurate large-scale atomic simulation. Compared with empirical interatomic potential based on the embedded-atom-method, the developed DNN-potential can accurately predict lattice constants, phonon properties, and mechanical properties under various thermodynamic conditions. Moreover, for the first time, we present the atomic evolution of the fracture behavior of large-scale rocksalt-structure (B1) TiN systems coupled with temperature and stress conditions. Our study validates that interatomic brittle fractures occur when TiN stretches beyond its tensile yield point. Such simulation of coating fracture and cutting behavior based on large-scale atoms can shed new light on understanding the microstructure and mechanical properties of coating tools under extreme operating conditions.
RESUMO
Shock-induced structural transformations in copper exhibit notable directional dependence and anisotropy, but the mechanisms that govern the responses of materials with different orientations are not yet well understood. In this study, we employ large-scale non-equilibrium molecular dynamics simulations to investigate the propagation of a shock wave through monocrystal copper and analyse the structural transformation dynamics in detail. Our results indicate that anisotropic structural evolution is determined by the thermodynamic pathway. A shock along the [Formula: see text] orientation causes a rapid and instantaneous temperature spike, resulting in a solid-solid phase transition. Conversely, a liquid metastable state is observed along the [Formula: see text] orientation due to thermodynamic supercooling. Notably, melting still occurs during the [Formula: see text]-oriented shock, even if it falls below the supercooling line in the thermodynamic pathway. These results highlight the importance of considering anisotropy, the thermodynamic pathway and solid-state disordering when interpreting phase transitions induced by shock. This article is part of the theme issue 'Dynamic and transient processes in warm dense matter'.
RESUMO
Compared to elemental gold (Au), Au-based alloys have attracted wide attention for their economy and superior performance stemming from their distinctive physicochemical properties. The study of the structural characterization for alloy materials remains one of the fundamental issues associated with their future applications essentially. In this work, we theoretically explore some typical intermetallic compounds of Au-based alloys under high pressure, which has been an effective means to generate intriguing crystal configurations with unexpected behaviors. Ourab initiosimulations find thatFd-3m-AuRb,Fd-3m-AuBa, andFd-3m-AuLa become stable above â¼10 GPa, andPmmn-AuAl becomes stable above â¼20 GPa. Further investigations of their compression behaviors reveal that the bulk moduli of Au-based alloys can be greatly reduced by combining alkali and alkaline earth metals. The present results have unraveled the high-pressure phases of Au-bearing compounds and provide insights for exploring their important compressibility that is strongly relevant to the containing non-Au elements.
RESUMO
This paper reports on the development of a magnetically driven high-velocity implosion experiment conducted on the CQ-3 facility, a compact pulsed power generator with a load current of 2.1 MA. The current generates a high Lorentz force between inner and outer liners made from 2024 aluminum. Equally positioned photonic Doppler velocimetry probes record the liner velocities. In experiment CQ3-Shot137, the inner liner imploded with a radial converging velocity of 6.57 km/s while the outer liner expanded at a much lower velocity. One-dimensional magneto-hydrodynamics simulation with proper material models provided curves of velocity versus time that agree well with the experimental measurements. Simulation then shows that the inner liner underwent a shock-less compression to approximately 19 GPa and reached an off-Hugoniot high-pressure state. According to the scaling law that the maximum loading pressure is proportional to the square of the load current amplitude, the results demonstrate that such a compact capacitor bank as CQ-3 has the potential to generate pressure as high as 100 GPa within the inner liner in such an implosion experiment. It is emphasized that the technique described in this paper can be easily replicated at low cost.
RESUMO
Deformation of metals has attracted great interest for a long time. However, the constitutive models for viscoplastic deformation at high strain rates are still under intensive development, and more physical mechanisms are expected to be involved. In this work, we employ the newly-proposed methodology of mesoscience to identify the mechanisms governing the mesoscale complexity of collective dislocations, and then apply them to improving constitutive models. Through analyzing the competing effects of various processes on the mesoscale behavior, we have recognized two competing mechanisms governing the mesoscale complex behavior of dislocations, i.e., maximization of the rate of plastic work, and minimization of the elastic energy. Relevant understandings have also been discussed. Extremal expressions have been proposed for these two mesoscale mechanisms, respectively, and a stability condition for mesoscale structures has been established through a recently-proposed mathematical technique, considering the compromise between the two competing mechanisms. Such a stability condition, as an additional constraint, has been employed subsequently to close a two-phase model mimicking the practical dislocation cells, and thus to take into account the heterogeneous distributions of dislocations. This scheme has been exemplified in three increasingly complicated constitutive models, and improves the agreements of their results with experimental ones.
RESUMO
Prediction of Peierls stress associated with dislocation glide is of fundamental concern in understanding and designing the plasticity and mechanical properties of crystalline materials. Here, we develop a nonlocal semi-discrete variational Peierls-Nabarro (SVPN) model by incorporating the nonlocal atomic interactions into the semi-discrete variational Peierls framework. The nonlocal kernel is simplified by limiting the nonlocal atomic interaction in the nearest neighbor region, and the nonlocal coefficient is directly computed from the dislocation core structure. Our model is capable of accurately predicting the displacement profile, and the Peierls stress, of planar-extended core dislocations in face-centered cubic structures. Our model could be extended to study more complicated planar-extended core dislocations, such as <110> {111} dislocations in Al-based and Ti-based intermetallic compounds.
RESUMO
Manipulating the shape and distribution of strengthening units, e.g. particles, fibers, and precipitates, in a bulk metal, has been a widely applied strategy of tailoring their mechanical properties. Here, we report self-assembled patterns of Gd nano-fibers in Mg-Gd alloys for the purpose of improving their strength and deformability. 1-nm Gd nano-fibers, with a ãcã-rod shape, are formed and hexagonally patterned in association with Gd segregations along dislocations that nucleated during hot extrusion. Such Gd-fiber patterns are able to regulate the relative activities of slips and twinning, as a result, overcome the inherent limitations in strength and ductility of Mg alloys. This nano-fiber patterning approach could be an effective method to engineer hexagonal metals.