Hydrogen Peroxide Electrochemical Sensor Based on Ag/Cu Bimetallic Nanoparticles Modified on Polypyrrole.

Due to the strong oxidizing properties of H2O2, excessive discharge of H2O2 will cause great harm to the environment. Moreover, H2O2 is also an energetic material used as fuel, with specific attention given to its safety. Therefore, it is of great importance to explore and prepare good sensitive materials for the detection of H2O2 with a low detection limit and high selectivity. In this work, a kind of hydrogen peroxide electrochemical sensor has been fabricated. That is, polypyrrole (PPy) has been electropolymerized on the glass carbon electrode (GCE), and then Ag and Cu nanoparticles are modified together on the surface of polypyrrole by electrodeposition. SEM analysis shows that Cu and Ag nanoparticles are uniformly deposited on the surface of PPy. Electrochemical characterization results display that the sensor has a good response to H2O2 with two linear intervals. The first linear range is 0.1-1 mM (R2 = 0.9978, S = 265.06 µA/ (mM × cm2)), and the detection limit is 0.027 µM (S/N = 3). The second linear range is 1-35 mM (R2 = 0.9969, 445.78 µA/ (mM × cm2)), corresponding to 0.063 µM of detection limit (S/N = 3). The sensor reveals good reproducibility (σ = 2.104), repeatability (σ = 2.027), anti-interference, and stability. The recoveries of the electrode are 99.84-103.00% (for 0.1-1 mM of linear range) and 98.65-104.80% (for 1-35 mM linear range). Furthermore, the costs of the hydrogen peroxide electrochemical sensor proposed in this work are reduced largely by using non-precious metals without degradation of the sensing performance of H2O2. This study provides a facile way to develop nanocomposite electrochemical sensors.

Carbon Coated Metal-Based Composite Electrode Materials for Lithium Sulfur Batteries: A Review.

Lithium-sulfur battery is one of the most promising secondary battery systems due to their high energy density and low material cost. During the past decade, great progress has been achieved in promoting the performances of Li-S batteries by addressing the challenges at the laboratory-level model systems. With growing attention paid to the application of Li-S batteries, new challenges at practical cell scales emerge as the bottleneck. However, challenges remain for the commercialization of lithium-sulfur batteries. The current review mainly focused on metal-based catalysts decorated-carbon materials for enhanced lithium sulfur battery performance. Firstly, the synthesis methods of various carbon-sulfur composites are discussed, as well as the influence of different material structures on the electrochemical performance. Secondly, a variety of catalysts, including metal atoms, metal oxides, sulfides, phosphides, nitrides, and carbide-decorated carbon nanomaterials, are systematically introduced to determine how lithium can be enhanced by suppressing polysulfides and promoting redox conversion reactions. Also, analyzed the multi-step electrochemical reaction mechanism of the battery during the charging and discharging process, and provide a feasible path for the practical application of high energy density lithium-sulfur batteries.

Graphene-Modified Co-B-P Catalysts for Hydrogen Generation from Sodium Borohydride Hydrolysis.

Sodium borohydride (NaBH4) is considered a good candidate for hydrogen generation from hydrolysis because of its high hydrogen storage capacity (10.8 wt%) and environmentally friendly hydrolysis products. However, due to its sluggish hydrogen generation (HG) rate in the water, it usually needs an efficient catalyst to enhance the HG rate. In this work, graphene oxide (GO)-modified Co-B-P catalysts were obtained using a chemical in situ reduction method. The structure and composition of the as-prepared catalysts were characterized, and the catalytic performance for NaBH4 hydrolysis was measured as well. The results show that the as-prepared catalyst with a GO content of 75 mg (Co-B-P/75rGO) exhibited an optimal catalytic efficiency with an HG rate of 12087.8 mL min-1 g-1 at 25 °C, far better than majority of the findings that have been reported. The catalyst had a good stability with 88.9% of the initial catalytic efficiency following 10 cycles. In addition, Co-, B-, and P-modified graphene showed a synergistic effect improving the kinetics and thermodynamics of NaBH4 hydrolysis with a lower activation energy of 28.64 kJ mol-1. These results reveal that the GO-modified Co-B-P catalyst has good potential for borohydride hydrolysis applications.