Fabrication and Characteristics of High Capacitance Al Thin Films Capacitor Using a Polymer Inhibitor Bath in Electroless Plating Process.

An aluminum (Al) thin film capacitor was fabricated for a high capacitance capacitor using electrochemical etching, barrier-type anodizing, and electroless Ni-P plating. In this study, we focused on the bottom-up filling of Ni-P electrodes on Al2O3/Al with etched tunnels. The Al tunnel pits were irregularly distributed on the Al foil, diameters were in the range of about 0.5~1 µm, the depth of the tunnel pits was approximately 35~40 µm, and the complex structure was made full filled hard metal. To control the plating rate, the experiment was performed by adding polyethyleneimine (PEI, C2H5N), a high molecular substance. PEI forms a cross-link at the etching tunnel inlet, playing the role of delaying the inlet plating. When the PEI solution bath was used after activation, the Ni-P layer was deposited selectively on the bottoms of the tunnels. The characteristics were analyzed by adding the PEI addition quantity rate of 100~600 mg/L into the DI water. The capacitance of the Ni-P/Al2O3 (650~700 nm)/Al film was measured at 1 kHz using an impedance/gain phase analyzer. For the plane film without etch tunnels the capacitance was 12.5 nF/cm2 and for the etch film with Ni-P bottom-up filling the capacitance was 92 nF/cm2. These results illustrate a remarkable maximization of capacitance for thin film metal capacitors.

The magnetic properties and microstructure of Co-Pt thin films using wet etching process.

Perpendicular magnetic recording (PMR) is a promising candidate for high density magnetic recording and has already been applied to hard disk drive (HDD) systems. However, media noise still limits the recording density. To reduce the media noise and achieve a high signal-to-noise ratio (SNR) in hard disk media, the grains of the magnetic layer must be magnetically isolated from each other. This study examined whether sputter-deposited Co-Pt thin films can have adjacent grains that are physically isolated. To accomplish this, the effects of the sputtering conditions and wet etching process on magnetic properties and the microstructure of the films were investigated. The film structure was Co-Pt (30 nm)/Ru (30 nm)/NiFe (10 nm)/Ta (5 nm). The composition of the Co-Pt thin films was Co-30.7 at.% Pt. The Co-Pt thin films were deposited in Ar gas at 5, 10, 12.5, and 15 mTorr. Wet etching process was performed using 7% nitric acid solution at room temperature. These films had high out-of-plane coercivity of up to 7032 Oe, which is twice that of the as-deposited film. These results suggest that wet etched Co-Pt thin films have weaker exchange coupling and enhanced out-of-plane coercivity, which would reduce the medium noise.

Effect of fluorine addition on the biological performance of hydroxyapatite coatings on Ti by aerosol deposition.

Dense and well-adherent fluoridated hydroxyapatite [Ca(10)(PO(4))(6)(OH)(2-x )F( x ), FHA] coatings with various amounts of fluorine contents (x = 0, 0.5, 1.0, 1.5, and 2.0) were deposited on commercially available pure titanium by aerosol deposition using FHA powders in order to investigate the effect of fluorine content on the properties of the coatings. FHA powders with different compositions were synthesized by solid-state reactions of hydroxyapatite (HA) and fluorapatite (FA) powders at various ratios. X-ray diffraction and Fourier transform infrared spectroscopy results showed that fluoride ions were successfully incorporated into the HA lattice for both the FHA powders and the FHA coatings. Scanning electron microscopy analysis revealed dense microstructures and good substrate adhesion of the coatings with high adhesion strengths of more than 33.1 MPa. The dissolution behavior in a tris-buffered saline solution indicated that the dissolution rate of the FHA coatings decreased as a result of increasing the fluorine content in the coatings. In addition, in vitro cellular tests, including cell attachment, proliferation, and alkaline phosphatase activity of MC3T3-E1 preosteoblast cells grown on the coatings, demonstrated that an FHA coating with a moderate degree of F(-) substitution, x = 1.0, had a stronger stimulating effect on cell proliferation and differentiation. These results suggested that there exists an optimum fluorine content level in the FHA coatings for the best long-term stability and cellular responses.

Comparison of radiation therapy alone and concurrent chemoradiation therapy in stage III cervical cancer: a multicenter retrospective study.

OBJECTIVE: To evaluate whether concurrent chemoradiation therapy (CRT) improves overall survival as compared to radiation therapy (RT) alone in stage III cervical cancers. DESIGN: A multicenter retrospective review. SETTING: Nine tertiary medical centers in Korea. POPULATION: A total of 277 patients treated for stage III cervical cancer without para-aortic lymph node (PALN) metastasis based on clinical staging workup from 1996 to 2003. METHODS: Medical and histopathological record review. MAIN OUTCOME MEASURES: Disease-specific overall survival. RESULTS: CRT and RT alone were performed in 172 and 105 patients, respectively. There was no significant difference in disease-specific overall survival between the CRT and RT alone arms based on clinical staging workup, even though the CRT arm was characterized by younger age, more favorable performance status and lower pretreatment blood urea nitrogen level as compared to the RT alone arm. In the CRT arm, three patients succumbed to treatment-related death. CONCLUSION: CRT does not improve the overall survival rate in stage III cervical cancer as compared to RT alone based on clinical staging workup for PALN status. Special care needs to be taken regarding optimal dose and duration of RT, use of brachytherapy, anemia control and accurate pretreatment staging workup to improve survival outcome in patients with stage III cervical cancer.

Polymerase chain reaction-based fluorescent Luminex assay to detect the presence of human papillomavirus types.

Becuase 40% of human papillomavirus (HPV) infections are mixed infections, the accurate identification of high-risk HPV genotypes in mixed infections is important for defining a woman's risk for progression to cervical cancer. Thus, advanced Luminex-based HPV genotyping has been developed to simultaneously detect the presence of multiple HPV types. Here, we describe the development of a Luminex-based HPV genotyping that combines polymerase chain reaction amplification with hybridization to fluorescence-labeled polystyrene bead microarrays (Luminex suspension array technology). New HPV type-specific oligonucleotide probes and YBT L1/GP6-1 primers were used to detect the HPV types in 132 clinical samples. We simultaneously evaluated the usefulness of this technique on clinical samples. We detected 15 specific HPV types (6, 16, 18, 31, 35, 42, 51, 52, 55, 56, 58, 59, 66, 67 and 68) examined with specificity without known cross-reaction to other HPV types. The detection limit for the different HPV types was above 500 plasmids. We compared the performance of the Luminex-based assay to the established HPV DNA microarray chip for polymerase chain reaction products derived from 53 clinical samples. The evaluation showed excellent agreement. The Luminex-based HPV genotyping was a sensitive, reproducible technique for the simultaneous genotyping of all clinically relevant genital HPV types. This assay system may be used to provide critical clinical information for early detection of HPV, especially in cases where the HPV copy numbers are low and the latency period of HPV infection is prolonged.

Protein expression profile using two-dimensional gel analysis in squamous cervical cancer patients.

PURPOSE: Screening in cervical cancer is now progressing to discover candidate genes and proteins that may serve as biological markers and that play a role in tumor progression. We examined the protein expression patterns of the squamous cell carcinoma (SCC) tissues from Korean women with using two- dimensional polyacrylamide gel electrophoresis (2-DE) and matrix assisted laser desorption/ionization-time of flight (MALDI- TOF) mass spectrometer. MATERIALS AND METHODS: Normal cervix and SCC tissues were solubilized and 2-DE was performed using pH 3 approximately 10 linear IPG strips of 17 cm length. The protein expression was evaluated using PDQuest 2-D software. The differentially expressed protein spots were identified with a MALDI-TOF mass spectrometer, and the peptide mass spectra identifications were performed using the Mascot program and by searching the Swiss-prot or NCBInr databases. RESULTS: A total of 35 proteins were detected in SCC. 17 proteins were up-regulated and 18 proteins were down-regulated. Among the proteins that were identified, 12 proteins (pigment epithelium derived factor, annexin A2 and A5, keratin 19 and 20, heat shock protein 27, smooth muscle protein 22 alpha, alpha-enolase, squamous cell carcinoma antigen 1 and 2, glutathione S-transferase and apolipoprotein a1) were protein previously known to be involved in tumor, and 21 proteins were newly identified in this study. CONCLUSION: 2-DE offers the total protein expression profiles of SCC tissues; further characterization of these differentially expressed proteins will give a chance to identify the badly needed tumor-specific diagnostic markers for SCC.