A-LLTO Nanoparticles Embedded Composite Solid Polymer Electrolyte for Room Temperature Operational Li-metal Batteries.

Solid-state batteries (SSBs) have the potential to revolutionize the current energy storage sector. A significant portion of the current development of electric vehicles and the electrification of various appliances relies on Lithium (Li)-ion batteries. However, future energy demands will require the development of stronger and more reliable batteries. This report presents a novel solid state electrolyte (SSE) composed of a self-healing composite solid polymer electrolyte (CSPE) matrix and aluminum-doped (Li0.33La0.56)1.005Ti0.99Al0.01O3 (A-LLTO) nanofillers. The CSPE contains Jeffamine ED-2003 monomer, Benzene-1,3,5-tricarbaldehyde (BTC) crosslinker dissolved in a 1:1 ratio of Dimethylformamide (DMF) to LiPF6, and a certain amount (x) of A-LLTO nanofillers (x = 5, 7.5, 10, 12.5%). A CSPE containing x-amount of A-LLTO fillers (referred to as CAL-x%) demonstrates excellent ion-conducting properties and stable battery performance. The CAL-10% demonstrates 1.1 × 10-3 S cm-1 of ionic conductivity at room temperature (RT). A-LLTO nanofillers dispersed uniformly within the polymer matrix form a percolation network, which is believed to improve ionic conductivity and the diffusion of Li+ ions. The CR-2032 cell, consisting of LiFePO4 (LFP)║CAL-10%║Li, at RT offers an initial discharge capacity of ≈165 mAh g-1 at 0.1C rate for 120 cycles with 98.85% coulombic efficiency (C.E.).

Diagnosing and staging epithelial ovarian cancer by serum glycoproteomic profiling.

BACKGROUND: There is a need for diagnostic tests for screening, triaging and staging of epithelial ovarian cancer (EOC). Glycoproteomics of blood samples has shown promise for biomarker discovery. METHODS: We applied glycoproteomics to serum of people with EOC or benign pelvic masses and healthy controls. A total of 653 analytes were quantified and assessed in multivariable models, which were tested in an independent cohort. Additionally, we analyzed glycosylation patterns in serum markers and in tissues. RESULTS: We identified a biomarker panel that distinguished benign lesions from EOC with sensitivity and specificity of 83.5% and 90.1% in the training set, and of 86.7 and 86.7% in the test set, respectively. ROC analysis demonstrated strong performance across a range of cutoffs. Fucosylated multi-antennary glycopeptide markers were higher in late-stage than in early-stage EOC. A comparable pattern was found in late-stage EOC tissues. CONCLUSIONS: Blood glycopeptide biomarkers have the potential to distinguish benign from malignant pelvic masses, and early- from late-stage EOC. Glycosylation of circulating and tumor tissue proteins may be related. This study supports the hypothesis that blood glycoproteomic profiling can be used for EOC diagnosis and staging and it warrants further clinical evaluation.

Mass Spectrometry Analysis of Glycopeptides Enriched by Anion Exchange-Mediated Methods Reveals PolyLacNAc-Extended N-Glycans in Integrins and Tetraspanins in Melanoma Cells.

Glycosylation is a key modulator of the functional state of proteins. Recent developments in large-scale analysis of intact glycopeptides have enabled the identification of numerous glycan structures that are relevant in pathophysiological processes. However, one motif found in N-glycans, poly-N-acetyllactosamine (polyLacNAc), still poses a substantial challenge to mass spectrometry-based glycoproteomic analysis due to its relatively low abundance and large size. In this work, we developed approaches for the systematic mapping of polyLacNAc-elongated N-glycans in melanoma cells. We first evaluated five anion exchange-based matrices for enriching intact glycopeptides and selected two materials that provided better overall enrichment efficiency. We then tested the robustness of the methodology by quantifying polyLacNAc-containing glycopeptides as well as changes in protein fucosylation and sialylation. Finally, we applied the optimal enrichment methods to discover glycopeptides containing polyLacNAc motifs in melanoma cells and found that integrins and tetraspanins are substantially modified with these structures. This study demonstrates the feasibility of glycoproteomic approaches for identification of glycoproteins with polyLacNAc motifs.

Variable PD-1 glycosylation modulates the activity of immune checkpoint inhibitors.

Monoclonal antibodies targeting the immune checkpoint PD-1 have provided significant clinical benefit across a number of solid tumors, with differences in efficacy and toxicity profiles possibly related to their intrinsic molecular properties. Here, we report that camrelizumab and cemiplimab engage PD-1 through interactions with its fucosylated glycan. Using a combination of protein and cell glycoengineering, we demonstrate that the two antibodies bind preferentially to PD-1 with core fucose at the asparagine N58 residue. We then provide evidence that the concentration of fucosylated PD-1 in the blood of non-small-cell lung cancer patients varies across different stages of disease. This study illustrates how glycoprofiling of surface receptors and related circulating forms can inform the development of differentiated antibodies that discriminate glycosylation variants and achieve enhanced selectivity, and paves the way toward the implementation of personalized therapeutic approaches.

Fabry-Perot Oscillation and Resonance Energy Transfer: Mechanism for Ultralow-Threshold Optically and Electrically Driven Random Laser in Quasi-2D Ruddlesden-Popper Perovskites.

The recently emerged metal-halide hybrid perovskite (MHP) possesses superb optoelectronic features, which have obtained great attention in solid-state lighting, photodetection, and photovoltaic applications. Because of its excellent external quantum efficiency, MHP has promising potential for the manifestation of ultralow threshold optically pumped laser. However, the demonstration of an electrically driven laser remains a challenge because of the vulnerable degradation of perovskite, limited exciton binding energy (Eb), intensity quenching, and efficiency drop by nonradiative recombinations. In this work, based on the paradigm of integration of Fabry-Perot (F-P) oscillation and resonance energy transfer, we observed an ultralow-threshold (∼250 µWcm-2) optically pumped random laser from moisture-insensitive mixed dimensional quasi-2D Ruddlesden-Popper phase perovskite microplates. Particularly, we demonstrated an electrically driven multimode laser with a threshold of ∼60 mAcm-2 from quasi-2D RPP by judicious combination of a perovskite/hole transport layer (HTL) and an electron transport layer (ETL) having suitable band alignment and thickness. Additionally, we showed the tunability of lasing modes and color by driving an external electric potential. Performing finite difference time domain (FDTD) simulations, we confirmed the presence of F-P feedback resonance, the light trapping effect at perovskite/ETL, and resonance energy transfer contributing to laser action. Our discovery of an electrically driven laser from MHP opens a useful avenue for developing future optoelectronics.

MTAP deficiency contributes to immune landscape remodelling and tumour evasion.

Methylthioadenosine phosphorylase (MTAP) deficiency occurs in various malignancies and is associated with poor survival in cancer patients. However, the mechanisms underlying tumour progression due to MTAP loss are yet to be elucidated. Utilizing integrated analyses of the transcriptome, proteome and secretome, we demonstrated that MTAP deficiency alters tumour-intrinsic, immune-related pathways and reprograms cytokine profiles towards a tumour-favourable environment. Additionally, MTAP-knockout cells exhibited a marked increase in the immune checkpoint protein PD-L1. Upon co-culturing primary T cells with cancer cells, MTAP loss-mediated PD-L1 upregulation inhibited T cell-mediated killing activity and induced several T cell exhaustion markers. In two xenograft tumour models, we showed a modest increase in average volume of tumours derived from MTAP-deficient cells than that of MTAP-proficient tumours. Surprisingly, a remarkable increase in tumour size was observed in humanized mice bearing MTAP-deficient tumours, as compared to their MTAP-expressing counterparts. Following immunophenotypic characterization of tumour-infiltrating leukocytes by mass cytometry analysis, MTAP-deficient tumours were found to display decreased immune infiltrates with lower proportions of both T lymphocytes and natural killer cells and higher proportions of immunosuppressive cells as compared to MTAP-expressing tumour xenografts. Taken together, our results suggest that MTAP deficiency restructures the tumour immune microenvironment, promoting tumour progression and immune evasion.

Surficial grafting of organoimido moieties enhances the capacity performance of oxometallic clusters.

Molybdenum trioxide (MoO3) with a theoretical specific capacity of 1117 mA h g-1 is widely considered a promising anode material for lithium-ion batteries. However, the irreversible conversion reactions, low electrical conductivity, and detrimental volume expansion upon Li intercalation between the one-dimensional layered structures of MoO3 hinder its practical implementation. Herein, we report a facile synthetic protocol that allows surficial modification by replacing the terminal and bridging oxo groups of molybdenum oxide clusters. Successful organoimido functionalization resulted in a large cathodic shift in Mo(VI/V) reduction by 0.6 V, pronounced electronic communication between the organic moiety and the metal-oxide unit, and significant increase in electrical conductivity (80-100 Ω interfacial charge-transfer resistance). Combined with the enlarged active surface area due to the structural hindrance induced by the organic functionality, the steady specific capacity of the organoimido-modified molybdenum oxide clusters was greater than 1200 mA h g-1 at 900 mA g-1 at the end of 360 cycles, where the best value of 1653 mA h g-1 was achieved for the nitroaniline-substituted species. The steady capacity of 480 mA h g-1 was achieved in the fast charge-discharge process (3000 mA g-1) over 1400 cycles. The results indicate that the surficial modification of metal oxides with organo moieties using our facile synthetic method has broad application potential for metal oxides to be used as high-capacity electrode materials in the future.

Sweetening Lithium Metal Interface by High Surface and Adhesive Energy Coating of Crystalline α-d-Glucose Film to Inhibit Dendrite Growth.

The notorious growth of lithium (Li) dendrites and the instability of the solid electrolyte interface (SEI) during cycling make Li metal anodes unsuitable for use in commercial Li-ion batteries. Herein, the use of simple sugar coating (α-d-glucose) is demonstrated on top of Li metal to halt the growth of Li dendrites and stabilize the SEI. The α-d-glucose layer possesses high surface and adhesive energies toward Li, which promote the homogenous stripping and plating of Li ions on top of the Li metal. Density functional theory reveals that Li-ion diffusion within the α-d-glucose layer is governed by hopping around the bare sides of the O atoms and along the apparent passages formed by the glucose molecules. Stable cycling performance is achieved when combining α-d-glucose-coated Li (G|Li) anodes with sulfur- and LiFePO4 -based cathodes in both LiTFSI (ether) and LiPF6 (carbonate) electrolyte systems. A G|Li-based symmetrical cell operates at a current density of 1 mA cm-2 and areal capacity of 1 mAh cm-2 displays a stable overpotential profile for over 9 months (7000 h) of continuous charge/discharge cycling.

Enhancing the Areal Capacity and Stability of Cu2ZnSnS4 Anode Materials by Carbon Coating: Mechanistic and Structural Studies During Lithiation and Delithiation.

The widespread use of energy storage technologies has created a high demand for the development of novel anode materials in Li-ion batteries (LIBs) with high areal capacity and faster electron-transfer kinetics. In this work, carbon-coated Cu2ZnSnS4 with a hierarchical 3D structure (CZTS@C) is used as an anode material for LIBs. The CZTS@C microstructures with enhanced electrical conductivity and improved Li-ion diffusivity exhibit high areal and gravimetric capacities of 2.45 mA h/cm2 and 1366 mA h/g, respectively. The areal capacity achieved in the present study is higher than that of previously reported CZTS-based materials. Moreover, in situ X-ray diffraction results show that lithium ions are stored in CZTS through the insertion reaction, followed by the alloying and conversion reactions at ∼1 V. The structural evolution of Li2S and Cu-Sn/Cu-Zn alloy phases occurs during the conversion and alloying reactions. The present work provides a cost-effective and simple method to prepare bulk CZTS and highlights the conformal carbon coating over CZTS, which can enhance the electrical and ionic conductivities of CZTS materials and increase the mass loading (1-2.3 mg/cm2). The improved stability and rate capability of CZTS@C anode materials can therefore be achieved.

Introducing Postmetalation Metal-Organic Framework to Control Perovskite Crystal Growth for Efficient Perovskite Solar Cells.

A novel lead-containing metal-organic framework (Pb-MOF) is synthesized through postmetalation of MOF-525. Postmetalation renders lead ions bound with the organic linker of MOF-525, which can serve as nucleation points to promote perovskite crystallization. The introduction of lead postmetalated MOF-525 (Pb-MOF) as a scaffold layer between compact TiO2 (c-TiO2) layer and perovskite layer promotes perovskite crystal growth in enlarging crystal grain size with better crystallinity, hence decreasing defect sites in the perovskite layer. Postmetalation of MOF-525 with lead ions allows MAPbI3 to form a solid crystal structure to facilitate the charge separation between electron transport layer (ETL) and light-harvesting layer so as to resolve the issue of possible vacancies present in MOFs. As a result, the champion perovskite solar cell (PSC) with the introduction of Pb-MOF exhibits a power conversion efficiency (PCE) of 20.87% and better stability (86% PCE retention after 40 days), outperforming the pristine PSC (16.85% PCE, with 52% retention after 40 days) and MOF-525-introduced PSC (18.61% PCE, with 76% retention after 40 days).

Light-controlled interconversion between a [c2]daisy chain and a lasso-type pseudo[1]rotaxane.

A light-responsive self-complementary crown ether/ammonium conjugate bearing an arylazopyrazole photoswitch as a spacer can be switched between a [c2]daisy chain (E-isomer) and a lasso-type pseudo[1]rotaxane (Z-isomer) by light.

Electrochemical Performance of Orthorhombic CsPbI3 Perovskite in Li-Ion Batteries.

A facile solution process was employed to prepare CsPbI3 as an anode material for Li-ion batteries. Rietveld refinement of the X-ray data confirms the orthorhombic phase of CsPbI3 at room temperature. As obtained from bond valence calculations, strained bonds between Pb and I are identified within PbI6 octahedral units. Morphological study shows that the as-prepared δ-CsPbI3 forms a nanorod-like structure. The XPS analysis confirm the presence of Cs (3d, 4d), Pb (4d, 4f, 5d) and I (3p, 3d, 4d). The lithiation process involves both intercalation and conversion reactions, as confirmed by cyclic voltammetry (CV) and first-principles calculations. Impedance spectroscopy coupled with the distribution function of relaxation times identifies charge transfer processes due to Li metal foil and anode/electrolyte interfaces. An initial discharge capacity of 151 mAhg-1 is found to continuously increase to reach a maximum of ~275 mAhg-1 at 65 cycles, while it drops to ~240 mAhg-1 at 75 cycles and then slowly decreases to 235 mAhg-1 at 100 cycles. Considering the performance and structural integrity during electrochemical performance, δ-CsPbI3 is a promising material for future Li-ion battery (LIB) application.

High-Performance Organic Solar Cells Featuring Double Bulk Heterojunction Structures with Vertical-Gradient Selenium Heterocyclic Nonfullerene Acceptor Concentrations.

In this study, we prepared organic photovoltaics (OPVs) featuring an active layer comprising double bulk heterojunction (BHJ) structures, featuring binary blends of a polymer donor and concentration gradients of two small-molecule acceptors. After forming the first BHJ structure by spin-coating, the second BHJ layer was transfer-printed onto the first using polydimethylsiloxane stamps. A specially designed selenium heterocyclic small-molecule acceptor (Y6-Se-4Cl) was employed as the second acceptor in the BHJ. X-ray photoelectron spectroscopy revealed that the two acceptors formed a gradient concentration profile across the active layer, thereby facilitating charge transportation. The best power conversion efficiencies (PCEs) for the double-BHJ-structured devices incorporating PM6:Y6-Se-4Cl/PM6:Y6 and PM6:Y6-Se-4Cl/PM6:IT-4Cl were 16.4 and 15.8%, respectively; these values were higher than those of devices having one-BHJ structures based on PM6:Y6-Se-4Cl (15.0%), PM6:Y6 (15.4%), and PM6:IT-4Cl (11.6%), presumably because of the favorable vertical concentration gradient of the selenium-containing small-molecule Y6-Se-4Cl in the active layer as well as some complementary light absorption. Thus, combining two BHJ structures with a concentration gradient of the two small-molecule acceptors can be an effective approach for enhancing the PCEs of OPVs.

High-Performance Organic Photovoltaics Incorporating an Active Layer with a Few Nanometer-Thick Third-Component Layer on a Binary Blend Layer.

In this paper, a universal approach toward constructing a new bilayer device architecture, a few-nanometer-thick third-component layer on a bulk-heterojunction (BHJ) binary blend layer, has been demonstrated in two different state-of-the-art organic photovoltaic (OPV) systems. Through a careful selection of a third component, the power conversion efficiency (PCE) of the device based on PM6/Y6/layered PTQ10 layered third-component structure was 16.8%, being higher than those of corresponding devices incorporating the PM6/Y6/PTQ10 BHJ ternary blend (16.1%) and the PM6/Y6 BHJ binary blend (15.5%). Also, the device featuring PM7/Y1-4F/layered PTQ10 layered third-component structure gave a PCE of 15.2%, which is higher than the PCEs of the devices incorporating the PM7/Y1-4F/PTQ10 BHJ ternary blend and the PM7/Y1-4F BHJ binary blend (14.2 and 14.0%, respectively). These enhancements in PCE based on layered third-component structure can be attributed to improvements in the charge separation and charge collection abilities. This simple concept of the layered third-component structure appears to have great promise for achieving high-performance OPVs.

Perovskite Quantum Wells Formation Mechanism for Stable Efficient Perovskite Photovoltaics-A Real-Time Phase-Transition Study.

The combination of a bulk 3D perovskite layer and a reduced dimensional perovskite layer (perovskite quantum wells (PQWs)) is demonstrated to enhance the performance of perovskite solar cells (PSCs) significantly in terms of stability and efficiency. This perovskite hierarchy has attracted intensive research interest; however, the in-depth formation mechanism of perovskite quantum wells on top of a 3D perovskite layer is not clearly understood and is therefore the focus of this study. Along with ex situ morphology and photophysical characterization, the time-resolved grazing-incidence wide-angle X-ray scattering (TS-GIWAXS) technique performed in this study provides real-time insights on the phase-transition during the organic cation (HTAB ligand molecule) coating and PQWs/3D architecture formation process. A strikingly strong ionic reaction between the 3D perovskite and the long-chain organic cation leads to the quick formation of an ordered intermediate phase within only a few seconds. The optimal PQWs/3D architecture is achieved by controlling the HTAB casting, which is assisted by time-of-flight SIMS characterization. By controlling the second ionic reaction during the long-chain cation coating process, along with the fluorinated poly(triarylamine) (PTAA) as a hole-transport layer, the perovskite solar cells demonstrate efficiencies exceeding 22% along with drastically improved device stability.

Perovskite Quantum Dot Lasing in a Gap-Plasmon Nanocavity with Ultralow Threshold.

Lead halide perovskite materials have recently received considerable attention for achieving an economic and tunable laser owing to their solution-processable feature and promising optical properties. However, most reported perovskite-based lasers operate with a large lasing-mode volume, resulting in a high lasing threshold due to the inefficient coupling between the optical gain medium and cavity. Here, we demonstrate a continuous-wave nanolasing from a single lead halide perovskite (CsPbBr3) quantum dot (PQD) in a plasmonic gap-mode nanocavity with an ultralow threshold of 1.9 Wcm-2 under 120 K. The calculated ultrasmall mode volume (∼0.002 λ3) with a z-polarized dipole and the significantly large Purcell enhancement at the corner of the nanocavity inside the gap dramatically enhance the light-matter interaction in the nanocavity, thus facilitating lasing. The demonstration of PQD nanolasing with an ultralow-threshold provides an approach for realizing on-chip electrically driven lasing and integration into on-chip plasmonic circuitry for ultrafast optical communication and quantum information processing.

Layered perovskite materials: key solutions for highly efficient and stable perovskite solar cells.

Metal halide perovskites having three-dimensional crystal structures are being applied successfully in various optoelectronic applications. To address their most challenging issues-instability and toxicity-without losing efficiency, lower-dimensional perovskites appear to be promising alternatives. Recently, two-dimensional (2D) perovskite solar cells have been developed exhibiting excellent photostability and moisture-stability, together with moderate device efficiency. This review summarizes the photophysical properties and operating mechanisms of 2D perovskites as well as recent advances in their applications in solar cell devices. Also presented is an agenda for the next-stage development of stable perovskite materials for solar cell applications, highlighting the issues of stability and toxicity that require further study to ensure commercialization.

Asymmetric Benzotrithiophene-Based Hole Transporting Materials Provide High-Efficiency Perovskite Solar Cells.

In this study, we synthesized a series of small-molecule benzotrithiophenes (BTTs) and used them as hole transporting materials (HTMs) in perovskite solar cells (PSCs). The asymmetric benzo[2,1-b:-3,4-b':5,6-b″]trithiophene unit was used as the central core to which were appended various donor groups, namely, carbazole (BTT-CB), thieno thiophene (BTT-FT), triphenylamine (BTT-TPA), and bithiophene (BTT-TT). The extended aromatic core in the asymmetric BTT provided full planarity, thereby favoring intermolecular π-stacking and charge transport. The physical, optical, and electrical properties of these small-molecule HTMs are reported herein. BTT-TT displayed good crystallinity and superior hole mobility, when compared with those of the other three HTMs, and formed smooth and uniform surfaces when covering the perovskite active layer. Accordingly, among the devices prepared in this study, a PSC incorporating BTT-TT as the HTM achieved the highest power conversion efficiency (18.58%). Moreover, this BTT-TT-containing device exhibited good stability after storage for more than 700 h. Thus, asymmetric BTTs are promising candidate materials for use as small-molecule HTMs in PSCs.

Modulating Performance and Stability of Inorganic Lead-Free Perovskite Solar Cells via Lewis-Pair Mediation.

Fully inorganic perovskites based on Bi3+ and Sb3+ are emerging as alternatives that overcome the toxicity and low stability of their Pb-based perovskite counterparts. Nevertheless, the thin film fabrication of Pb-free perovskites remains a struggle, with poor morphologies and incomplete conversions greatly inhibiting device performance. In this study, we modulated the crystallization of an all-inorganic dimer phase of a Sb perovskite (d-Cs3Sb2I9) through gradual increase in the annealing temperature, accompanied by the use of Lewis bases for adduct formation. Here, the role of Lewis pairing in the crystallization of the resulting Pb-free Cs3Sb2I9 thin films has been investigated. Both, "S-donor" (thiourea) and "O-donor" [N-methylpyrrolidone (NMP)] Lewis bases are examined for their abilities to form adducts with Cs+ and Sb3+ cations. Furthermore, density functional theory has been used to estimate the binding energies of these Lewis bases with the Cs3Sb2I9 lattice. Temperature-dependent photoluminescence spectroscopy revealed the nature of the band gap of d-Cs3Sb2I9. The efficiency of the resulting perovskite solar cells was enhanced to 1.8%, with excellent stability observed, when using NMP to form the adduct film. To the best of our knowledge, this is the best solar cell efficiency for the dimer phase of the inorganic Sb-based perovskite. The effects of both S- and O-donors are studied under various environmental stresses to reveal the stability responses of the devices.

Core-Twisted Tetrachloroperylenediimides: Low-Cost and Efficient Non-Fullerene Organic Electron-Transporting Materials for Inverted Planar Perovskite Solar Cells.

Herein, core-twisted tetrachloroperylenediimides (ClPDIs) were introduced as new efficient electron-transporting materials (ETMs) to replace the commonly used fullerene acceptor PC61 BM in inverted planar perovskite solar cells (PSCs). ClPDI showed a low-lying lowest unoccupied molecular orbital (LUMO) energy level of -3.95 eV, which was compatible with the conduction band of CH3 NH3 PbI3-x Clx (-3.90 eV). In addition, the role of the length of the alkyl side chain at the imide position of ClPDI in modulating the molecular solubility, aggregation capacity for charge-transport properties, surface hydrophobicity, and PSC performance was investigated. The device based on ClPDI-C4 (ClPDI with n-butyl side chains) as ETM achieved a maximum power conversion efficiency (PCE) of 17.3 % under standard AM 1.5G illumination, which iwas very competitive with that of the reference device employing PC61 BM/C60 (PCE=17.2 %) as ETM. Moreover, the devices with ClPDIs as ETMs exhibited better device stability than that with PC61 BM/C60 . This work highlights the great potential of ClPDI derivatives as low-cost (≈2.0 USD g-1 ) and effective ETMs to obtain efficient solution-processed inverted PSCs. This class of ClPDI derivatives is expected further promote the performance and stability of PSCs after extended investigation.