Graphite-type activated carbon from coconut shell: a natural source for eco-friendly non-volatile storage devices.

Carbon from biomass as an active material for supercapacitor electrodes has attracted much interest due to its environmental soundness, abundance, and porous nature. In this context, activated carbon prepared from coconut shells via a simple activation process (water or steam as activation agents) was used as an active material in electrodes for eco-friendly supercapacitors. X-ray diffraction (XRD), Raman spectroscopy, conductivity, scanning electron microscopy (SEM), N2 sorption and thermogravimetry coupled to mass spectrometry (TGA-MS) studies revealed that activated carbon produced by this approach exhibit a graphitic phase, a high surface area, and large pore volume. The energy storage properties of activated carbon electrodes correlate with the morphological and structural properties of the precursor material. In particular, electrodes made of activated carbon exhibiting the largest Brunauer-Emmett-Teller (BET) surface area, i.e. 1998 m2 g-1, showed specific capacitance of 132.3 F g-1 in aqueous electrolyte (1.5 M H2SO4), using expanded graphite sheets as current collector substrates. Remarkably, this sample in a configuration with ionic liquid (1-methyl-1-propy-pyrrolizinium bis(fluorosulfonyl)mide) (MPPyFSI) as electrolyte and a polyethylene separator displayed an outstanding storage capability and energy-power handling capability of 219.4 F g-1 with a specific energy of 92.1 W h kg-1 and power density of 2046.9 W kg-1 at 1 A g-1 and maintains ultra-high values at 30 A g-1 indicating the ability for a broad potential of energy and power related applications. To the best of our knowledge, these values are the highest ever reported for ionic liquid-based supercapacitors with activated carbon obtained from the biomass of coconut shells.

Vapor-Phase Formation of a Hole-Transporting Thiophene Polymer Layer for Evaporated Perovskite Solar Cells.

Homogeneous layer formation on textured silicon substrates is essential for the fabrication of highly efficient monolithic perovskite silicon tandem solar cells. From all well-known techniques for the fabrication of perovskite solar cells (PSCs), the evaporation method offers the highest degree of freedom for layer-by-layer deposition independent of the substrate's roughness or texturing. Hole-transporting polymers with high hole mobility and structural stability have been used as effective hole-transporting materials (HTMs) of PSCs. However, the strong intermolecular interactions of the polymers do not allow for a layer formation via the evaporation method, which is a big challenge for the perovskite community. Herein, we first applied a hole-transporting terthiophene polymer (PTTh) as an HTM for evaporated PSCs via an in situ vapor-phase polymerization using iodine (I2) as a sublimable oxidative agent. PTTh showed high hole mobility of 1.2 × 10-3 cm2/(V s) and appropriate energy levels as HTM in PSCs (EHOMO = -5.3 eV and ELUMO = -3.3 eV). The PSCs with the in situ vapor-phase polymerized PTTh hole-transporting layer and a co-evaporated perovskite layer exhibited a photovoltaic conversion efficiency of 5.9%, as a proof of concept, and high cell stability over time. Additionally, the polymer layer could fully cover the pyramidal structure of textured silicon substrates and was identified as an effective hole-transporting material for perovskite silicon tandem solar cells by optical simulation.

Semi-Transparent Perovskite Solar Cells with ITO Directly Sputtered on Spiro-OMeTAD for Tandem Applications.

Perovskite silicon tandem solar cells have the potential to overcome the efficiency limit of single-junction solar cells. For both monolithic and mechanically stacked tandem devices, a semi-transparent perovskite top solar cell, including a transparent contact, is required. Usually, this contact consists of a metal oxide buffer layer and a sputtered transparent conductive oxide. In this work, semi-transparent perovskite solar cells in the regular n-i-p structure are presented with tin-doped indium oxide (ITO) directly sputtered on the hole conducting material Spiro-OMeTAD. ITO process parameters such as sputter power, temperature, and pressure in the chamber are systematically varied. While a low temperature of 50 °C is crucial for good device performance, a low sputter power has only a slight effect, and an increased chamber pressure has no influence on device performance. For the 5 × 5 mm2 perovskite cell with a planar front side, a 105 nm thick ITO layer with a sheet resistance of 44 Ω sq-1 allowing for the omission of grid fingers and a MgF2 antireflection coating are used to improve transmission into the solar cells. The best device achieved an efficiency of 14.8%, which would result in 24.2% in a four-terminal tandem configuration.

Detailed Investigation of Evaporated Perovskite Absorbers with High Crystal Quality on Different Substrates.

Dual-source vapor-phase deposition enables low-temperature fabrication of high-performance planar structure perovskite (CH3NH3PbI3) solar cells (PSCs), applicable in tandem devices or for industrial production with high homogeneity. Herein, we report low-temperature fabrication of high-efficiency PSCs by dual-source vapor-phase deposition and significance of TiO2 surface modification with [6,6]-phenyl C61 butyric acid methyl ester (PCBM) on cell performance. Co-evaporation of PbI2 and CH3NH3I, as confirmed by X-ray diffraction and high-resolution transmission electron microscopy analyses, results in CH3NH3PbI3 layers with a well-crystallized tetragonal phase formed on both TiO2 and TiO2/PCBM electron-transport layers (ETLs). The devices with PCBM interlayer between TiO2 and CH3NH3PbI3 showed remarkably higher performance than those with TiO2 only, which was attributed to enhance charge extraction and reduced recombination at the TiO2/PCBM/CH3NH3PbI3 interface. The devices composed of evaporated CH3NH3PbI3 on top of the TiO2/PCBM and [2,2',7,7'-tetrakis( N, N-di- p-methoxyphenyl-amine)-9,9'-spirobifluorene] (Spiro-OMeTAD) as hole-transport material demonstrated power conversion efficiencies of 17.1% (reverse scan) and 13.4% (forward scan) with stabilized efficiency of over 16%, which is, to the best of our knowledge, the highest efficiency reported for evaporated perovskite solar cells using low-temperature fabrication method involving compact TiO2 layer as ETL. Furthermore, we show that this process can be used to deposit a CH3NH3PbI3 layer on top of a textured silicon substrate, which is the first step for preparing perovskite-silicon tandem devices with enhanced antireflection and light-trapping properties.

Material challenges for solar cells in the twenty-first century: directions in emerging technologies.

Photovoltaic generation has stepped up within the last decade from outsider status to one of the important contributors of the ongoing energy transition, with about 1.7% of world electricity provided by solar cells. Progress in materials and production processes has played an important part in this development. Yet, there are many challenges before photovoltaics could provide clean, abundant, and cheap energy. Here, we review this research direction, with a focus on the results obtained within a Japan-French cooperation program, NextPV, working on promising solar cell technologies. The cooperation was focused on efficient photovoltaic devices, such as multijunction, ultrathin, intermediate band, and hot-carrier solar cells, and on printable solar cell materials such as colloidal quantum dots.

Self-Organized Superlattice and Phase Coexistence inside Thin Film Organometal Halide Perovskite.

Organometal halide perovskites have attracted widespread attention as the most favorable prospective material for photovoltaic technology because of their high photoinduced charge separation and carrier transport performance. However, the microstructural aspects within the organometal halide perovskite are still unknown, even though it belongs to a crystal system. Here direct observation of the microstructure of the thin film organometal halide perovskite using transmission electron microscopy is reported. Unlike previous reports claiming each phase of the organometal halide perovskite solely exists at a given temperature range, it is identified that the tetragonal and cubic phases coexist at room temperature, and it is confirmed that superlattices composed of a mixture of tetragonal and cubic phases are self-organized without a compositional change. The organometal halide perovskite self-adjusts the configuration of phases and automatically organizes a buffer layer at boundaries by introducing a superlattice. This report shows the fundamental crystallographic information for the organometal halide perovskite and demonstrates new possibilities as promising materials for various applications.

Adjustment of Conduction Band Edge of Compact TiO2 Layer in Perovskite Solar Cells Through TiCl4 Treatment.

Perovskite solar cells (PSCs) without a mesoporous TiO2 layer, that is, planar-type PSCs exhibit poorer cell performance as compared to PSCs with a porous TiO2 layer, owing to inefficient electron transfer from the perovskite layer to the compact TiO2 layer in the former case. The matching of the conduction band levels of perovskite and the compact TiO2 layer is thus essential for enhancing PSC performance. In this study, we demonstrate the shifting of the conduction band edge (CBE) of the compact TiO2 layer through a TiCl4 treatment, with the aim of improving PSC performance. The CBE of the compact TiO2 layer was shifted to a higher level through the TiCl4 treatment and then shifted in the opposite direction, that is, to a lower level, through a subsequent heat treatment. These shifts in the CBE were reflected in the PSC performance. The TiCl4-treated PSC showed an increase in the open-circuit voltage of more than 150 mV, as well as a decrease of 100 mV after being heated at 450 °C. On the other hand, the short-circuit current decreased after the treatment but increased after heating at temperatures higher than 300 °C. The treated PSC subjected to subsequent heating at 300 °C exhibited the best performance, with the power conversion efficiency of the PSC being 17% under optimized conditions.

Determination of unique power conversion efficiency of solar cell showing hysteresis in the I-V curve under various light intensities.

Energy harvesting at low light intensities has recently attracted a great deal of attention of perovskite solar cells (PSCs) which are regarded as promising candidate for indoor application. Anomalous hysteresis of the PSCs a complex issue for reliable evaluation of the cell performance. In order to address these challenges, we constructed two new evaluation methods to determinate the power conversion efficiencies (PCEs) of PSCs. The first setup is a solar simulator based on light emitting diodes (LEDs) allowing evaluation of the solar cells at wider range of light intensities, ranging from 102 to 10-3 mW·cm-2. As the overestimate error, we found that the PCEs of dye sensitized solar cell (DSC) and PSCs increase dramatically at low light intensities conditions. Due to the internal capacitance at the interfaces on hybrid solar cells, the measurement of current below 10-2 mW·cm-2 shows constant value given high PCE, which is related to the capacitive current and origin of the hysteresis. The second setup is a photovoltaic power analyzing system, designed for tracking the maximum power (P max) with time. The paper suggests the combination of the LED solar simulator and P max tracking technique as a standard to evaluate the PCE of capacitive solar cells.

Enhancement of the hole conducting effect of NiO by a N2 blow drying method in printable perovskite solar cells with low-temperature carbon as the counter electrode.

In this article, we demonstrate for the first time a mesoscopic printable perovskite solar cell (PSC) using NiO as the hole transporting material and low-temperature processed carbon as the counter electrode. A single deposition method assisted by N2 blow drying was used for the deposition of MAPbI3 on a TiO2/ZrO2/NiO screen-printed electrode. As the final step a low-temperature processing (i.e. 75 °C) carbon counter layer was fabricated on MAPbI3 by a blade coating method. It is found that the capping layer thickness of MAPbI3 has a significant effect on the device efficiency, especially when NiO is introduced as a hole transporting material into the structure. Electrochemical impedance spectroscopy demonstrates good charge transport characteristics for the device with a thin MAPbI3 capping layer obtained by the N2 blow drying method. Our best performing device demonstrated a remarkable photovoltaic performance with a short-circuit current density (Jsc) of 22.38 mA cm-2, an open circuit voltage (Voc) of 0.97 V, and a fill factor (FF) of 0.50 corresponding to a photo-conversion efficiency (PCE) of 10.83%. Moreover, the un-encapsulated device exhibited advantageous stability over 1000 h in air in the dark.