A Network of Processes for Biorefining Burdock Seeds and Roots.

In this work, a novel sustainable approach was proposed for the integral valorisation of Arctium lappa (burdock) seeds and roots. Firstly, a preliminary recovery of bioactive compounds, including unsaturated fatty acids, was performed. Then, simple sugars (i.e., fructose and sucrose) and phenolic compounds were extracted by using compressed fluids (supercritical CO2 and propane). Consequently, a complete characterisation of raw biomass and extraction residues was carried out to determine the starting chemical composition in terms of residual lipids, proteins, hemicellulose, cellulose, lignin, and ash content. Subsequently, three alternative ways to utilise extraction residues were proposed and successfully tested: (i) enzymatic hydrolysis operated by Cellulases (Thricoderma resei) of raw and residual biomass to glucose, (ii) direct ethanolysis to produce ethyl levulinate; and (iii) pyrolysis to obtain biochar to be used as supports for the synthesis of sulfonated magnetic iron-carbon catalysts (Fe-SMCC) to be applied in the dehydration of fructose for the synthesis of 5-hydroxymethylfurfural (5-HMF). The development of these advanced approaches enabled the full utilisation of this resource through the production of fine chemicals and value-added compounds in line with the principles of the circular economy.

Ethanol organosolv pretreatment of sugarcane bagasse assisted by organic acids and supercritical carbon dioxide.

The scCO2-assisted organosolv pretreatment of sugarcane bagasse was carried out using aqueous ethanol and organic acid catalysts. Variables involved were temperature (150-190 °C), time (0-60 min), type of catalyst (acetic, citric, and oxalic acids), amount of CO2 (25-50 g), ethanol titer in water (0-80 vol%), and catalyst concentration (0.5 to 1.5 % w·v-1). The best delignification (86 wt%) and glucan retention (89 wt%) were achieved at 170 °C for 15 min using 60 vol% ethanol in water, 1 wt% oxalic acid, and 25 g CO2. Organic acid esterification was a limitation for pretreatment operations using ethanol titers above 60 vol%. Enzymatic hydrolysis of pretreated materials at 1 % (w·v-1) glucans released 74.3 ± 0.2 % glucose in 96 h using Cellic CTec3 (Novozymes) at 9.89 FPU·gglucans-1. The concentrated pretreatment liquor allowed lignin recovery by water precipitation in high yields, while the aqueous supernatant contained low levels of fermentation inhibitors.

Phytochemicals and Biological Activities of Burdock (Arctium lappa L.) Extracts: A Review.

Arctium lappa L., also known as burdock, is an edible wild plant which has the ability to grow in distinct environments and is considered a weed in several parts of the world. This species has great value in the biological and medical fields with its major secondary components being phenolic compounds and terpenes, substances rich in desired biological activities as antioxidant, antimicrobial, antitumor and anti-inflammatory. In addition, burdock leaves extracts have shown a modulatory effect on the complement system, which plays an important role in the development of inflammatory diseases, with an inhibitory effect on all complement pathways. Thus, natural products with those relevant activities are promising agents for healthcare applications. Therefore, the species A. lappa may represent an interesting asset for researching and developing new therapies for inflammatory afflictions.

Enhancing the Recovery of Bioactive Compounds of Soybean Fermented with Rhizopus oligosporus Using Supercritical CO2: Antioxidant, Anti-Inflammatory, and Oxidative Proprieties of the Resulting Extract.

The aim of the present study was to evaluate the use of supercritical CO2 combined with cosolvent for the recovery of bioactive compounds of soybean fermented with Rhizopus oligosporus NRRL 2710. Soxhlet extractions using seven different organic solvents (n-hexane, petroleum ether, ethyl acetate, acetone, ethanol, methanol, and water) were initially performed for comparative purposes. The extracts obtained were characterized by physicochemical, antioxidant, total phenolic, and oxidative proprieties. For the Soxhlet extractions, the highest and lowest yields obtained were 45.24% and 15.56%, using methanol and hexane, respectively. The extraction using supercritical CO2 combined with ethanol as a static modifier (scCO2 + EtOH) presented, at a high pressure (25 MPa) and temperature (80 °C), a phenolic compound content of 1391.9 µg GAE g-1 and scavenging of 0.17 g, reaching a 42.87% yield. The extracts obtained by sCO2 + EtOH were characterized by high contents of essential fatty acids (linoleic acid and oleic acid) and bioactive compounds (gallic acid, trans-cinnamic acid, daidzein, and genistein). These extracts also showed a great potential for inhibiting hyaluronidase enzymes (i.e., anti-inflammatory activity). Thermogravimetric analyses of the samples showed similar profiles, with oil degradation values in the range from 145 to 540 °C, indicating progressive oil decomposition with a mass loss ranging from 93 to 98.7%. In summary, this study demonstrated the flexibility of scCO2 + EtOH as a green technology that can be used to obtain high-value-added products from fermented soybean.

Performing under pressure: esterification activity of dry fermented solids in subcritical and supercritical CO2.

OBJECTIVE: Lipases are often used in immobilized form, but commercial immobilized lipases are costly. An alternative is to produce lipases in solid-state fermentation, dry the solids and then use the "dry fermented solids" (DFS) directly. We produced DFS by growing Burkholderia contaminans on a mixture of sugarcane bagasse and sunflower seed meal and used the DFS to esterify oleic acid with ethanol in subcritical and supercritical CO2 at 40 °C. RESULTS: Compared to a control without CO2 at atmospheric pressure, subcritical CO2 at 30 bar improved esterification activity 1.2-fold. Higher pressures, including supercritical pressures up to 150 bar, reduced activity to less than 80% of the control. At 30 bar, the esterification activity was improved a further 1.8-fold with the addition of 9% water (i.e. 9 g water per 100 g oleic acid) to the reaction medium. CONCLUSION: A subcritical CO2 atmosphere, with the addition of a small amount of water, improved the esterification activity of DFS containing lipases of Burkholderia contaminans.

Supercritical Fluids: A Promising Technique for Biomass Pretreatment and Fractionation.

Lignocellulosic biomasses are primarily composed of cellulose, hemicelluloses and lignin and these biopolymers are bonded together in a heterogeneous matrix that is highly recalcitrant to chemical or biological conversion processes. Thus, an efficient pretreatment technique must be selected and applied to this type of biomass in order to facilitate its utilization in biorefineries. Classical pretreatment methods tend to operate under severe conditions, leading to sugar losses by dehydration and to the release of inhibitory compounds such as furfural (2-furaldehyde), 5-hydroxy-2-methylfurfural (5-HMF), and organic acids. By contrast, supercritical fluids can pretreat lignocellulosic materials under relatively mild pretreatment conditions, resulting in high sugar yields, low production of fermentation inhibitors and high susceptibilities to enzymatic hydrolysis while reducing the consumption of chemicals, including solvents, reagents, and catalysts. This work presents a review of biomass pretreatment technologies, aiming to deliver a state-of-art compilation of methods and results with emphasis on supercritical processes.

Effects of pressurized hot water extraction on the yield and chemical characterization of pectins from Campomanesia xanthocarpa Berg fruits.

Pressurized hot water extraction (PHWE), known as a "green" extraction technique, was used to obtain polysaccharide from the pulp of gabiroba (Campomanesia xanthocarpa Berg) fruits. The effects of pressure, temperature, and flow rate on pectin yields were analyzed through a full factorial design experiment 23. The optimal extraction conditions to achieve maximum pectin yield (5.70 wt%) were pressure of 150 bar, temperature of 120 °C, and flow rate of 1.5 mL min-1. The high pressure (100 bar) promoted an increase in galacturonic acid content (36.0%) compared to conventional hot water extraction (CEGP) with 25.7%. Differences in the proportion of homogalacturonan (HG) and rhamnogalacturonan (RG-I) domains ranging from 16.3 to 35.4% and 61.7 to 80.1%, respectively, were observed for each pectin sample according to the extraction conditions. The mono-dimensional (13C-NMR) and bi-dimensional (1H/13C HSQC-NMR) analyses confirmed the presence of HG and RG-I regions and indicated the presence of arabinogalactans type I (AG-I) and arabinogalactans type II (AG-II) in the PHWE pectin samples, which was not found for pectins from gabiroba pulp obtained by CEGP. The results showed that PHWE proved to be a promising method for extracting pectins from gabiroba fruits.

Inhibitory Effect of Supercritical Extracts from Arctium lappa L. on the Lectin Pathway of the Complement System.

The complement system participates in host defense by eliminating microorganisms and triggering inflammation. However, insufficient control or exacerbated complement activation contributes to inflammatory diseases. Since promising antioxidant and anti-inflammatory activities have been identified in Arctium lappa L. extracts, this study aims to explore the effect of A. lappa extracts on the lectin pathway (LP) of complement activation. Four extracts were obtained by supercritical extraction using scCO2 with or without ethanol as co-solvent, at different temperatures and pressures (E1: 2.2 mg/mL, E2: 2.6 mg/mL and E3: 2.0 mg/mL, E4: 1.5 mg/mL). To evaluate the effect of A. lappa extracts on the LP activation, an ELISA assay using mannose binding lectin pathway of complement was carried out with C4 detection. All extracts showed a concentration-dependent inhibitory effect on the activation of complement by the LP. The following IC50 were observed for E1, E2, E3 and E4: 179.4 µg/mL, 74.69 µg/mL, 119.1 µg/mL and 72.19 µg/mL, respectively. Our results suggest that A. lappa extracts are potential candidates for the treatment of inflammatory disorders that are complement-related.

Effect of grilling and baking on physicochemical and textural properties of tilapia (Oreochromis niloticus) fish burger.

The influence of two common cooking methods, grilling and baking, on chemical composition, water retention, fat retention, cooking yield, diameter reduction, expressible water, color and mechanical texture of tilapia (Oreochromis niloticus) fish burgers was investigated. Texture analyses were performed using a Warner-Bratzler test. The fish burger had a softer texture with a lower shear force than other meat products reported in the literature. There were no significant differences in proximate composition, diameter reduction, fat retention and expressible water between the grilled and oven-baked fish burgers. Cooking methods did not affect the cooking times and cooking rates. Warner-Bratzler parameters and color were significantly influenced by the cooking method. Grilling contributed to a shear force and work of shearing increase due to the lower cooking yield and water retention. Raw burgers had the highest L* (69.13 ± 0.96) and lowest b* (17.50 ± 0.75) values. Results indicated that baking yielded a product with better cooking characteristics, such as a desired softer texture with lower shear values (4.01 ± 0.54) and increased water retention (95.82 ± 0.77). Additionally, the baked fish burgers were lighter (higher L*) and less red (lower a*) than the grilled ones.

Influence of two different alcohols in the esterification of fatty acids over layered zinc stearate/palmitate.

In this work, esterification of fatty acids (oleic, linoleic and stearic acid) with a commercial zinc carboxylate (a layered compound formed by simultaneous intercalation of stearate and palmitate anions) was performed. Kinetic modeling using a quasi-homogeneous approach successfully fitted experimental data at different molar ratio of fatty acids/alcohols (1-butanol and 1-hexanol) and temperature. An apparent first-order reaction related to all reactants was found and activation energy of 66 kJ/mol was reported. The catalyst showed to be unique, as it can be easily recovered like a heterogeneous catalysts behaving like ionic liquids. In addition, this catalyst demonstrated a peculiar behavior, because higher reactivity was observed with the increase in the alcohols chain length compared to the authors' previous work using ethanol.

Supercritical carbon dioxide combined with 1-butyl-3-methylimidazolium acetate and ethanol for the pretreatment and enzymatic hydrolysis of sugarcane bagasse.

The use of green solvents for the partial delignification of milled sugarcane bagasse (1mm particle size) and for the enhancement of its susceptibility to enzymatic hydrolysis was demonstrated. The experiments were carried out for 2h using 40 g of supercritical carbon dioxide combined with 1-butyl-3-methylimidazolium acetate and 15.8 g of ethanol. The effects of temperature (110-180 °C), pressure (195-250 bar) and IL-to-bagasse mass ratio (0:1-1:1) were investigated through a factorial design in which the response variables were the extent of delignification and both anhydroglucose and anhydroxylose contents in the pretreated materials. The highest delignification degree (41%) led to the best substrate for hydrolysis, giving a 70.7 wt% glucose yield after 12h using 5 wt% and Cellic CTec2® (Novozymes) at 10 mg g(-1) total solids. Hence, excellent substrates for hydrolysis were produced with a minimal IL requirement, which could be recovered by ethanol washing for its downstream processing and reuse.

Kinetics of enzymatic hydrolysis of olive oil in batch and fed-batch systems.

This work reports experimental data, kinetic modeling, and simulations of enzyme-catalyzed hydrolysis of olive oil. This reaction was performed in batch system and an ordered-sequential Bi Bi model was used to model the kinetic mechanism. A fed-batch system was proposed and experimental data were obtained and compared to the simulated values. The kinetic model used was able to correlate the experimental data, in which a satisfactory agreement between the experimental data and modeling results was obtained under different enzyme concentration and initial free water content. Therefore, the modeling allowed a better understanding of the reaction kinetics and affords a fed-batch simulation for this system. From the results obtained, it was observed that the fed-batch approach showed to be more advantageous when compared to the conventional batch system.

Thermodynamic modeling of ternary liquid-liquid systems with forming immiscibility islands

The aim of this work was to study the application of a stochastic algorithm to correlate the experimental data of island-type systems in ternary systems. Thermodynamic NRTL and UNIQUAC models were used to evaluate the activity coefficients. Results regarding the application of the stochastic algorithm were in good agreement with those presented in the current literature. However, generalization of the method proposed in the present work remained an intriguing and complex task so as to reach broad conclusions.

Kinetics of enzyme-catalyzed hydrolysis of steam-exploded sugarcane bagasse.

This work presents the experimental kinetic data and the fractal modeling of sugarcane bagasse steam treatment and enzymatic hydrolysis. Sugarcane bagasse (50 wt% moisture) was pretreated by autohydrolysis at 210 °C for 4 min. Acid catalysis involved the use of 9.5mg g(-1) of H2SO4 or H3PO4 in relation to the substrate dry mass at these same pretreatment conditions. Unwashed, water-washed and alkali-washed substrates were hydrolyzed at 2.0 wt% using 8 and 15 FPU g(-1) (108.22 and 199.54 mg/g) total solids of a Celluclast 1.5 L and Novozym 188 mixture (Novozymes). The fractal kinetic modeling was used to describe the effect of pretreatment and both washing processes on substrate accessibility. Water and/or alkali washing was not strictly necessary to achieve high hydrolysis efficiencies. Also, the fractal model coefficients revealed that H3PO4 was a better pretreatment catalyst under the experimental conditions used in this study, resulting in the most susceptible substrates for enzymatic hydrolysis.

Kinetic modeling of solvent-free lipase-catalyzed partial hydrolysis of palm oil.

This work reports the experimental data and kinetic modeling of diacylglycerol (DAG) production from palm oil using a commercial immobilized lipase (Lipozyme RM IM) in a solvent-free medium. The experiments were performed in batch mode, at 55 °C and 400 rpm, and the effects of enzyme concentration (0.68-2.04 wt% related to the mass of substrates), initial water concentration (5-15 wt% related to the mass of oil), and reaction time were evaluated. A novel kinetic model is presented based on the ordered-sequential bi-bi mechanism considering hydrolysis and esterification steps, in which a correlation between water-in-oil solubility and surfactant molecules concentration in the oil allowed the model to describe the induction period in the beginning of the hydrolysis reaction. Moreover, mass transfer limitations related to the enzyme concentration in the system were also taken into account. The proposed model presented a very satisfactory agreement with the experimental data, thus allowing a better understanding of the reaction kinetics. The best conditions obtained for the product (partially hydrolyzed palm oil) in terms of DAG yield (35.91 wt%) were 2.87 wt% enzyme/substrate, 2.10 wt% water/oil, and 72 h of reaction.