Automated method for the solid phase extraction of tetracyclines in wastewater followed by fluorimetric determination.

This work presents a multisyringe flow injection analysis (MSFIA) system for the automatic extraction and determination of tetracyclines in wastewater samples. The sample was adjusted with Na2EDTA buffer before solid-phase extraction with an Oasis HLB column used for the analyte preconcentration. The europium (Eu3+)-based and citrate-mediated method (using Tris-HCl buffer) was selected for the fluorimetric analysis (λexc/em = 400/612 nm). For fluorescence detection, a low-cost system consisting of an USB 2000 CCD detector and a 3D-printed support that holds a LED light source was used. Under optimized conditions, the proposed method provided low limits of detection (9.4 µg L-1) and quantification (31 µg L-1), and good values for intra-day (<4 %) and inter-day precisions (<6 %). Recoveries of spiked TCs in wastewater samples ranged from 87 to 106 %. The results of this work were in good agreement with the measurements obtained by liquid chromatography coupled to a fluorescence detector.

Determination of dissolved nickel in natural waters using a rapid microplate fluorescence assay method.

A new microplate analytical procedure is described for the determination of nickel (Ni2+) ions in natural water samples. A lophine analogue fluorescent sensor was synthesized and a spectral study showed a selective fluorescence quenching effect of chemical sensor by Ni2+ under optimized conditions. Density functional theory (DFT) calculations confirmed the formation of a Ni(II)L3 complex obtained by the Job plot. The calculations showed that the fluorescence emission peak of L collapses due to the distortion of L in the complex. The simple and fast microplate procedure allowed us to quantify Ni2+ with a linear response from 1.6 to 40 µg L-1 and a quantification limit of 5.4 µg L-1 without the need of a preconcentration step. The optimized procedure using high-throughput microplate assay has been applied for the determination of Ni2+ in natural water samples with good analytical performances.

Multisyringe Flow Injection Analysis of Tropomyosin Allergens in Shellfish Samples.

This paper presents the development and the application of a multisyringe flow injection analysis system for the fluorimetric determination of the major heat-stable known allergen in shrimp, rPen a 1 (tropomyosin). This muscle protein, made up of 284 amino acids, is the main allergen in crustaceans and can be hydrolyzed by microwave in hydrochloric acid medium to produce glutamic acid, the major amino acid in the protein. Glutamic acid can then be quantified specifically by thermal conversion into pyroglutamic acid followed by chemical derivatization of the pyroglutamic acid formed by an analytical protocol based on an OPA-NAC reagent. Pyroglutamic acid can thus be quantified between 1 and 100 µM in less than 15 min with a detection limit of 1.3 µM. The method has been validated by measurements on real samples demonstrating that the response increases with the increase in the tropomyosin content or with the increase in the mass of the shrimp sample.

Sub-ppb mercury detection in real environmental samples with an improved rhodamine-based detection system.

A new procedure is described for the determination of Hg2+ ions in water samples. A Rhodamine based fluorescent sensor was synthesized and the experimental conditions were specifically optimized for application to environmental samples, which requires low detection limits and high selectivity in competitive experiments with realistic concentrations of other metal ions. Incorporation of a Rhodamine-6G fluorophore to a previously described sensor and optimization of the buffer system (detection with acetic acid at pH 5.25) enabled significant enhancement of the sensitivity (detection limit = 0.27 µg L-1) and selectivity. The optimized procedure using high-throughput microplates has been applied to tap and river waters with good results.

Implication of phytometabolites on metal tolerance of the pseudo-metallophyte -Rosmarinus officinalis- in a Mediterranean brownfield.

This study highlights the trace metal and metalloid (TMM) accumulation in Rosmarinus officinalis L. and its chemical responses when exposed to high levels of contamination. R. officinalis individuals growing along a gradient of mixed TMM soil pollution, resulting from past industrial activities, were analysed. Several plant secondary metabolites, known to be involved in plant tolerance to TMM or as a plant health indicator, were investigated. The levels of thiol compounds and phytochelatin precursors (cysteine and glutathione) in the shoots were measured in the laboratory, while a portable non-destructive instrument was used to determine the level of phenolic compounds and chlorophylls directly on site. The level of Pb, As, Sb and Zn contaminations within the soil and plants was also determined. The results highlighted a decrease of TMM translocation with increases of soil contamination. The concentration of TMM in the shoots followed the Mitscherlich equation and reached a plateau at 0.41, 7.9, 0.37, 51.3 mg kg-1 for As, Pb, Sb and Zn, respectively. In the shoots, the levels of thiols and phenols were correlated to concentrations of TMM. Glutathione seems to be the main thiol compounds involved in the tolerance to As, Pb and Sb. Phenols indices, using non-destructive measurements, may be considered as an easy way to establish a proxy to estimate the TMM contamination level of the R. officinalis shoots. The study highlights metabolic processes that contribute to the high potential of R. officinalis for phytostabilisation of TMM in contaminated areas in the Mediterranean.

Development of an automated system for the analysis of inorganic chloramines in swimming pools via multi-syringe chromatography and photometric detection with ABTS.

Inorganic chloramines are disinfection by-products resulting from the unwanted reaction between chlorine used as disinfectant in swimming pools and nitrogenous compounds brought by bathers. This parameter (total chloramines or combined chlorine) is currently measured on site by a colorimetric method that does not allow to measure only inorganic chloramines. In this paper, a multi-syringe chromatography system combined with a post column derivatization is applied for the first time for the specific detection of the three individual inorganic chloramines (monochloramine, dichloramine and trichloramine). These latter ones are separated using a low-pressure monolithic C18 column, and separately detected after a post-column reaction with the chromogenic reagent ABTS (2,2'-azino-bis-(3-ethyl-benzothiazoline)-6-sulfonic acid-diammonium salt). Development of two ABTS reagents provides discrimination of chlorine and monochloramine that are not separated on the column. Optimization of the experimental conditions enables determination of inorganic chloramines with very good detection limits (around 10 µg eq.Cl2 L-1) without interferences from other chlorinated compounds such as organic chloramines or free available chlorine. The validation of the whole procedure has been successfully applied to real swimming pools samples.

Modified 3D-printed device for mercury determination in waters.

3D printing technology is increasingly used in flow analysis, to develop low cost and tailor-made devices. The possibility of grafting specific molecules onto 3D printed parts offers new perspectives for the development of flow systems. In this study, a MPFS system including a dicarboxylate 1,5-diphenyl-3-thiocarbazone grafted 3D-printed device has been developed for mercury determination. For this purpose, the surface of 3D-printed cuboids was first modified with amine functional groups and then grafted with dicarboxylate 1,5-diphenyl-3-thiocarbazone. This new grafted device resulted in selective mercury preconcentration with extraction and elution yields higher than 90% even at high sampling flow rates. The detection can then be carried out in two ways: a direct detection of mercury extracted onto 3D-printed grafted cuboids by atomic absorption spectrophotometry after amalgam on gold or a detection of mercury in solution after elution with l-cysteine by spectrophotometry or cold vapour atomic absorption spectrometry.

Development of transient mutagenic activity following the chlorination of the sunscreen UV filter dioxybenzone (benzophenone-8) in bromide-rich water.

The mutagenicity of four organic UV filters namely oxybenzone (benzophenone-3), dioxybenzone (benzophenone-8), avobenzone, and octyl methoxycinnamate, in chlorinated bromide-rich water (artificial seawater) was investigated. Mutagenicity was evaluated using Ames test in Salmonella typhimurium TA98 without S9 mix. Chemical analysis using high-resolution mass spectrometry was carried out to elucidate the mutagenic transformation products. Among the studied UV filters, only dioxybenzone exhibited a clear mutagenic activity following chlorination in seawater at ratio 1:10 (UV filter:chlorine). In contrast, no mutagenic activity was detected when chlorine was added at higher doses (ratio 1:1000). High-resolution mass spectrometry analysis showed that mutagenic extracts contained several brominated transformation products of dioxybenzone. Time course analysis of the transformation products at increasing chlorine doses showed that they were unstable and disappeared more quickly at higher chlorine doses. This instability explained the absence of mutagenic activity of dioxybenzone when 1000-fold excess chlorine was added, as no transformation products were detected. Relevance of these findings to the context of swimming pool is discussed. Further investigations taking into consideration the mutagenicity of not only the intermediate transformation products but also the final disinfection byproducts are needed to determine the overall impact of high levels of chlorine on the overall mutagenicity. This study highlights the importance of considering the reactivity of organic UV filters and their transformation products in disinfected recreational waters when sunscreen formulations are prepared.

3D-printed lab-on-valve for fluorescent determination of cadmium and lead in water.

In recent years, the development of 3D printing in flow analysis has allowed the creation of new systems with various applications. Up to now, 3D printing was mainly used for the manufacture of small units such as flow detection cells, preconcentration units or mixing systems. In the present study, a new 3D printed lab-on-valve system was developed to selectively quantify lead and cadmium in water. Different technologies were compared for lab-on-valve 3D printing. Printed test units have shown that stereolithography or digital light processing are satisfactory techniques for creating complex lab-on-valve units. The lab-on-valve system was composed of two columns, eight peripheral ports and a central port, and a coil integrating baffles to increase mixing possibilities. A selective extraction of lead was first carried out by TrisKem Pb™ Resin column. Then, cadmium not retained on the first column was extracted on a second column of Amberlite® IR 120 resin. In a following step, lead and cadmium were eluted with ammonium oxalate and potassium iodide, respectively. Finally, the two metals were sequentially detected by the same Rhod-5N™ fluorescent reagent. This 3D printed lab-on-valve flow system allowed us to quantify lead and cadmium with a linear response from 0.2 to 15 µg L-1 and detection limits of 0.17 and 0.20 µg L-1 for lead and cadmium, respectively, which seems adapted for natural water analysis.

Degradation of Organic UV filters in Chlorinated Seawater Swimming Pools: Transformation Pathways and Bromoform Formation.

Organic ultraviolet (UV) filters are used in sunscreens and other personal-care products to protect against harmful effects of exposure to UV solar radiation. Little is known about the fate of UV filters in seawater swimming pools disinfected with chlorine. The present study investigated the occurrence and fate of five commonly used organic UV filters, namely dioxybenzone, oxybenzone, avobenzone, 2-ethylhexyl-4-methoxycinnamate, and octocrylene, in chlorinated seawater swimming pools. Pool samples were collected to monitor the variation of UV filter concentrations during pool opening hours. Furthermore, laboratory-controlled chlorination experiments were conducted in seawater spiked with UV filters to investigate the reactivity of UV filters. Extracts of chlorination reaction samples were analyzed using high-resolution mass spectrometry and electron-capture detection to identify the potentially formed byproducts. In the collected pool samples, all the UV filters except dioxybenzone were detected. Chlorination reactions showed that only octocrylene was stable in chlorinated seawater. The four reactive UV filters generated brominated transformation products and disinfection byproducts. This formation of brominated products resulted from reactions between the reactive UV filters and bromine, which is formed rapidly when chlorine is added to seawater. Based on the identified byproducts, the transformation pathways of the reactive UV filters were proposed for the first time. Bromoform was generated by all the reactive UV filters at different yields. Bromal hydrate was also detected as one of the byproducts generated by oxybenzone and dioxybenzone.

Monitoring and factors affecting levels of airborne and water bromoform in chlorinated seawater swimming pools.

Water and air quality of eight seawater swimming pools using chlorine disinfection was measured during four sampling campaigns, spread on one full-year, and in four thalassotherapy centers located in Southeast of France. Concentrations of trihalomethanes (THMs) in air and in water as well as concentrations of parameters, including nonpurgeable organic carbon (NPOC), free residual chlorine (Clf), pH, Kjeldhal Nitrogen (KN), salinity, conductivity, bromide ions and, water and air temperature, were measured. Water and air samples were collected in triplicates morning - at the opening of the pools -, noon and night - at the closing of the pools -, in summer and winter. Data analysis was performed by Principal Component Analysis (PCA) and rotated component matrix, from both data quality and other parameters such as TOC, aromaticity (UV254), pH, hygrometry, and free residual chlorine (Clf). This statistical analysis demonstrates a high correlation between TOC, Clf and UV254 and THM levels found in air and water, particularly for the major ones (CHBr3 in water: 300.0µg/L mean, 1029.0µg/L maximum; CHBr3 in air: 266.1µg/m3 mean, 1600.0µg/m3 maximum, and CHClBr2 in water: 18.9µg/L mean, 81.0µg/L maximum; CHClBr2 in air: 13.6µg/m3 mean, 150.0µg/m3 maximum). These high levels of bromoform (CHBr3) are particularly worrisome in such health institutions, even these levels do not exceed the Permissible Exposure Limit (PEL) of 5mg/m3 as an 8hour time-weighted average currently fixed by various administrations, such as Occupational Safety and Health Administration (OSHA).

3D-printed flow system for determination of lead in natural waters.

The development of 3D printing in recent years opens up a vast array of possibilities in the field of flow analysis. In the present study, a new 3D-printed flow system has been developed for the selective spectrophotometric determination of lead in natural waters. This system was composed of three 3D-printed units (sample treatment, mixing coil and detection) that might have been assembled without any tubing to form a complete flow system. Lead was determined in a two-step procedure. A preconcentration of lead was first carried out on TrisKem Pb Resin located in a 3D-printed column reservoir closed by a tapped screw. This resin showed a high extraction selectivity for lead over many tested potential interfering metals. In a second step, lead was eluted by ammonium oxalate in presence of 4-(2-pyridylazo)-resorcinol (PAR), and spectrophotometrically detected at 520nm. The optimized flow system has exhibited a linear response from 3 to 120µgL-1. Detection limit, coefficient of variation and sampling rate were evaluated at 2.7µgL-1, 5.4% (n=6) and 4 sampleh-1, respectively. This flow system stands out by its fully 3D design, portability and simplicity for low cost analysis of lead in natural waters.

Occurrence of brominated disinfection byproducts in the air and water of chlorinated seawater swimming pools.

An undesirable consequence of disinfection is the formation of chemical contaminants known as disinfection byproducts (DBPs). Chronic exposure to DBPs has been linked to adverse health effects. The occurrence of DBPs in chlorinated pools filled with seawater (such as thalassotherapy pools and pools in spas) has received little attention so far. The present study evaluated the speciation and levels of disinfection byproducts in indoor swimming pools filled with seawater and treated with chlorine. Water and air samples were collected from three indoor swimming pools located in Southern France. Several classes of DBPs including trihalomethanes, haloacetic acids, haloacetonitriles, and trihaloacetaldehydes were analyzed in water. Halogenated volatile organic compounds were analyzed in air. Extractable organic halides (EOX) contents were determined using combustion/micro-coulometry system. The speciation of DBPs identified in the three pools was predominantly brominated. The mean (arithmetic) concentration of bromoform, dibromoacetic acid, tribromoacetic acid, dibromoacetonitrile and bromal hydrate in the three pools was 79.2, 72.9, 59.9, 26.9 and 10.0µg/L, respectively. By weight, HAAs represented the most abundant chemical class followed by THMs. In air, bromoform was the most abundant THM occurring at a mean concentration of 133.2µg/m3 in the three pools. The mean EOX level was 706µgCl-/L for the three pools. In average, the quantified DBPs accounted for only 14% of EOX, thus 86% of EOX remained unknown. Further research is warranted to identify the unknown DBPs.

Occurrence, origin, and toxicity of disinfection byproducts in chlorinated swimming pools: An overview.

Disinfection treatments are critical to conserve the microbiological quality of swimming pool water and to prevent water-borne infections. The formation of disinfection byproducts (DBPs) in swimming pools is an undesirable consequence resulting from reactions of disinfectants (e.g. chlorine) with organic and inorganic matter present in pool water, mainly brought by bathers. A considerable body of occurrence studies has identified several classes of DBPs in swimming pools with more than 100 compounds detected, mainly in chlorinated freshwater pools. Trihalomethanes (THMs), haloacetic acids (HAAs), haloacetaldehydes (HALs) are among the major DBPs in swimming pools. Other DBPs such as haloacetonitriles (HAN), haloamines, nitrosamines, and halobenzoquinones have also been detected. Researchers have been interested in identifying the precursors responsible for the formation of DBPs. In swimming pools, anthropogenic organic loads brought by swimmers increase the complexity of pool water chemistry. When human inputs (e.g. sweat, urine, hair, skin and personal care products) containing very diverse organic compounds are introduced to pools by swimmers, they react with chlorine resulting in the formation of complex mixtures of DBPs. The overwhelming majority of the total organic halide (TOX) content is still unknown in swimming pools. Exposure of swimmers to DBPs can take place through multiple routes, depending on the chemical properties of each DBP. Toxicological studies have shown that swimming pool water can be mutagenic with different potencies reported in different studies. Many DBPs have been shown to be genotoxic and carcinogenic. DBPs were also shown to induce reproductive and neurotoxic adverse effects in animal studies. Epidemiologic studies in humans have shown that exposure to DBPs increases the risk of respiratory adverse effects and bladder cancer. Association between DBPs and other health effects are still inconclusive. Data gathered in the present review (occurrence, toxicity, and toxicological reference values) could be used in conducting chemical risk assessment studies in swimming pools.

Assessing the genotoxicity of two commonly occurring byproducts of water disinfection: Chloral hydrate and bromal hydrate.

Water disinfection treatments result in the formation of disinfection byproducts (DBPs) that have been linked to adverse human health outcomes including higher incidence of bladder and colorectal cancer. However, data about the genotoxicity of DBPs is limited to only a small fraction of compounds. Chloral hydrate (CH) and bromal hydrate (BH) are two trihaloacetaldehydes commonly detected in disinfected waters, but little is known about their genotoxicity, especially BH. We investigated the genotoxicity of CH and BH using a test battery that includes three in vitro genotoxicity assays. We conducted the Ames test using Salmonella bacterial strains TA97a, TA98, TA100 and TA102, and the alkaline comet assay and the micronucleus test both using Chinese hamster ovary cells. We carried out the tests in the absence and presence of the metabolic fraction S9 mix. CH did not exhibit statistically significant genotoxic effects in any of the three assays. In contrast, BH exhibited mutagenic activity in the Salmonella strain TA100 and induced statistically significant DNA lesions in CHO cells as appeared in the comet assay. The genotoxic potential of BH in both assays decreased in the presence of the metabolic fraction S9 mix. BH did not induce chromosomal damage in CHO cells. Our results show that BH exhibited genotoxic activity by causing mutations and primary DNA damage while CH did not induce genotoxic effects. Our findings highlight concerns about the higher genotoxicity of brominated DBPs in comparison to their chlorinated analogues.

Evaluation of an integrated constructed wetland to manage pig manure under Mediterranean climate.

Pig manure is a complex mixture with excessive nutrients such as ammonium, microbial pathogens and may contain contaminants such as antibiotics. Conventional pig manure management practices caused water contamination. Sludge treatment wetland has been evaluated to determine its potential use under Mediterranean climate aiming at a parsimonious use of water and preventing water contamination, two major steps to preserve water resources in the Mediterranean Basin. Preliminary NH4-N degradation was tested using aeration process and/or addition of commercial bacterial products. Aeration alone appeared to be sufficient to ensure nitrogen transformation of the pig manure at lab small-scale (10 L) and medium-scale (300 L). Selected plant species e.g., Carex hispida for use in the integrated constructed wetland tolerated the nitrogen content after aeration enabling their use in a treatment vertical bed.

Identification of disinfection by-products in freshwater and seawater swimming pools and evaluation of genotoxicity.

Exposure to disinfection byproducts (DBPs) in swimming pools has been linked to adverse health effects. Numerous DBPs that occur in swimming pools are genotoxic and carcinogenic. This toxicity is of a greater concern in the case of brominated DBPs that have been shown to have substantially greater toxicities than their chlorinated analogs. In chlorinated seawater swimming pools, brominated DBPs are formed due to the high content of bromide. Nevertheless, very little data is reported about DBP occurrence and mutagenicity of water in these pools. In the present study, three seawater and one freshwater swimming pools located in Southeastern France were investigated to determine qualitatively and quantitatively their DBP contents. An evaluation of the genotoxic properties of water samples of the freshwater pool and a seawater pool was conducted through the Salmonella assay (Ames test). The predominant DBPs identified in the freshwater pool were chlorinated species and included trichloroacetic acid, chloral hydrate, dichloroacetonitrile, 1,1,1-trichloropropanone and chloroform. In the seawater pools, brominated DBPs were the predominant species and included dibromoacetic acid, bromoform and dibromoacetonitile. Bromal hydrate levels were also reported. In both types of pools, haloacetic acids were the most prevalent chemical class among the analyzed DBP classes. The distribution of other DBP classes varied depending on the type of pool. As to genotoxicity, the results of Ames test showed higher mutagenicity in the freshwater pool as a consequence of its considerably higher DBP contents in comparison to the tested seawater pool.

Degradation Products of Benzophenone-3 in Chlorinated Seawater Swimming Pools.

Oxybenzone (2-hydroxy-4-methoxyphenone, benzophenone-3) is one of the UV filters commonly found in sunscreens. Its presence in swimming pools and its reactivity with chlorine has already been demonstrated but never in seawater swimming pools. In these pools, chlorine added for disinfection results in the formation of bromine, due to the high levels of bromide in seawater, and leads to the formation of brominated disinfection byproducts, known to be more toxic than chlorinated ones. Therefore, it seems important to determine the transformation products of oxybenzone in chlorinated seawater swimming pools; especially that users of seawater swimming pools may apply sunscreens and other personal-care products containing oxybenzone before going to pools. This leads to the introduction of oxybenzone to pools, where it reacts with bromine. For this purpose, the reactivity of oxybenzone has been examined as a function of chlorine dose and temperature in artificial seawater to assess its potential to produce trihalomethanes and to determine the byproducts generated following chlorination. Increasing doses of chlorine and increasing temperatures enhanced the formation of bromoform. Experiments carried out with excess doses of chlorine resulted in the degradation of oxybenzone and allowed the determination of the degradation mechanisms leading to the formation of bromoform. In total, ten transformation products were identified, based on which the transformation pathway was proposed.

Β-hydroxymyristic acid as a chemical marker to detect endotoxins in dialysis water.

An analytical chemical method has been developed for determination of ß-hydroxymyristic acid (ß-HMA), a component of lipopolysaccharides (LPSs/endotoxins) in dialysis water. In our investigation, the ß-HMA component was used as a chemical marker for endotoxin presence in dialysis water because it is available in the molecular subunit (lipid A) and responsible for toxicity. It is the most abundant saturated fatty acid in that subunit. The developed method is based on fluorescence derivatization with 4-nitro-7-piperazino-2,1,3-benzoxadiazole (NBD-PZ). A high-performance liquid chromatographic separation of the ß-HMA derivative was achieved using an octadecyl silica column in gradient elution. A wide dynamic range of ß-HMA was tested and a calibration curve was constructed with accuracy of 90% and variability of less than 10%. The limits of detection and quantification obtained were 2 and 5µM, respectively. The developed method was applied to detect endotoxins in dialysis water by alkaline hydrolysis of LPS using NaOH (0.25M) at 60°C for 2h. After hydrolysis, free acid was detected as its NBD-PZ derivative using high-performance liquid chromatography/mass spectrometry (HPLC/MS). Good recovery rates ranging from 98 to 105% were obtained for ß-HMA in dialysis water.

Impact of organic pollutants on metal and As uptake by helophyte species and consequences for constructed wetlands design and management.

Various industrial processes and anthropogenic activities in urban areas induce a release of metals, metalloids and organic pollutants. Phytoremediation of co-contaminated waters in constructed wetlands is a promising solution for reducing the impact on natural environments. In order to improve the design and management of constructed wetlands, more knowledge is needed concerning the effect of organic pollutants on plant metal and metalloid uptake. In this study, the effects of a mixture of organic pollutants commonly found in industrial effluents (hydrocarbons, polycyclic aromatic hydrocarbons, anionic detergent) on the uptake of ten metals and metalloids (MM), i.e. Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn, by five helophytes having a wide European distribution were studied. Main effects of plant species and pollutant conditions on metal uptake and interactions between factors were determined by a statistical treatment of a microcosm experiment. Overall, the order of element uptake in plants was Fe > Al > Mn > Cr, Ni, Zn, > Cu > As, Cd, Pb, which was consistent with relative concentrations in the rhizosphere environment of microcosms. Larger amounts of metals were retained in belowground biomass of plants than in aboveground parts. Statistical analysis showed that organic pollutants enhanced the accumulation of Mn in whole plants and the retention of Fe in belowground parts, while they reduced the accumulation of Cd, Ni, and Zn in whole plants and the retention of Cu in belowground parts. For the other MM (Al, As, Cr, Pb), effects were variable, depending on the plant species. Among the five plants tested, Carex cuprina generally removed the highest quantities of MM, which was the result of both a high metal accumulation capacity and high biomass production. Nevertheless, no significant proportion of the MM total loading could be removed in plants' aboveground parts.