Effects of Four Prototype Gasoline Particle Filters (GPFs) on Nanoparticle and Genotoxic PAH Emissions of a Gasoline Direct Injection (GDI) Vehicle.

The fast replacement of traditional gasoline port-fuel injection technology with gasoline direct-injection (GDI) vehicles is expected to have a substantial impact on urban air quality. Herein we report on effects of four prototype gasoline particle filters (GPFs) on exhausts of a 1.6 L Euro-5 GDI vehicle. Two noncoated and two filters with catalytic coatings were investigated. These filters, on average, lowered PN emissions 4-7-fold to 4.0-6.8 × 1011 particles/km. Genotoxic PAHs were lowered 2-5-fold too with GPF-1-3, with GPF-1 having the highest efficiency, 79% and resulting in 45 ng toxic equivalent concentration (TEQ)/km. Thus, particle filtration efficiencies and reduction of the genotoxic potentials are correlated. GPF-4 showing the poorest particle filtration efficiency (66-78%) also released exhausts with highest genotoxic potential of 240-530 ng TEQ/km. We recently reported particle-number (PN) emissions of four generations of GDI vehicles (Euro-3 to Euro-6) which released, on average, 2.5 × 1012 ± 1.8 × 1012 particles/km exceeding the current European limit of 6.0 × 1011 particle/km. Thus, the implementation of filters to GDI vehicles requires best-available technology (BAT) with PN efficiencies >98% and catalytic activity, to avoid store-and-release of genotoxic PAHs. In-series applications of BAT-filters to GDI vehicles can lower genotoxic PAHs and soot nanoparticles.

Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations.

Retrofitting older vehicles with diesel particulate filter (DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%-1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23-560nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency.

Respiratory hazard assessment of combined exposure to complete gasoline exhaust and respirable volcanic ash in a multicellular human lung model at the air-liquid interface.

Communities resident in urban areas located near active volcanoes can experience volcanic ash exposures during, and following, an eruption, in addition to sustained exposures to high concentrations of anthropogenic air pollutants (e.g., vehicle exhaust emissions). Inhalation of anthropogenic pollution is known to cause the onset of, or exacerbate, respiratory and cardiovascular diseases. It is further postulated similar exposure to volcanic ash can also affect such disease states. Understanding of the impact of combined exposure of volcanic ash and anthropogenic pollution to human health, however, remains limited. The aim of this study was to assess the biological impact of combined exposure to respirable volcanic ash (from Soufrière Hills volcano (SHV), Montserrat and Chaitén volcano (ChV), Chile; representing different magmatic compositions and eruption styles) and freshly-generated complete exhaust from a gasoline vehicle. A multicellular human lung model (an epithelial cell-layer composed of A549 alveolar type II-like cells complemented with human blood monocyte-derived macrophages and dendritic cells cultured at the air-liquid interface) was exposed to diluted exhaust (1:10) continuously for 6 h, followed by immediate exposure to the ash as a dry powder (0.54 ±â€¯0.19 µg/cm2 and 0.39 ±â€¯0.09 µg/cm2 for SHV and ChV ash, respectively). After an 18 h incubation, cells were exposed again for 6 h to diluted exhaust, and a final 18 h incubation (at 37 °C and 5% CO2). Cell cultures were then assessed for cytotoxic, oxidative stress and (pro-)inflammatory responses. Results indicate that, at all tested (sub-lethal) concentrations, co-exposures with both ash samples induced no significant expression of genes associated with oxidative stress (HMOX1, NQO1) or production of (pro-)inflammatory markers (IL-1ß, IL-8, TNF-α) at the gene and protein levels. In summary, considering the employed experimental conditions, combined exposure of volcanic ash and gasoline vehicle exhaust has a limited short-term biological impact to an advanced lung cell in vitro model.

Gasoline particle filter reduces oxidative DNA damage in bronchial epithelial cells after whole gasoline exhaust exposure in vitro.

A substantial amount of traffic-related particle emissions is released by gasoline cars, since most diesel cars are now equipped with particle filters that reduce particle emissions. Little is known about adverse health effects of gasoline particles, and particularly, whether a gasoline particle filter (GPF) influences the toxicity of gasoline exhaust emissions. We drove a dynamic test cycle with a gasoline car and studied the effect of a GPF on exhaust composition and airway toxicity. We exposed human bronchial epithelial cells (ECs) for 6 hours, and compared results with and without GPF. Two hours later, primary human natural killer cells (NKs) were added to ECs to form cocultures, while some ECs were grown as monocultures. The following day, cells were analyzed for cytotoxicity, cell surface receptor expression, intracellular markers, oxidative DNA damage, gene expression, and oxidative stress. The particle amount was significantly reduced due to GPF application. While most biological endpoints did not differ, oxidative DNA damage was significantly reduced in EC monocultures exposed to GPF compared to reference exhaust. Our findings indicate that a GPF has beneficial effects on exhaust composition and airway toxicity. Further studies are needed to assess long-term effects, also in other cell types of the lung.

Assessment of lung cell toxicity of various gasoline engine exhausts using a versatile in vitro exposure system.

Adverse effect studies of gasoline exhaust are scarce, even though gasoline direct injection (GDI) vehicles can emit a high number of particles. The aim of this study was to conduct an in vitro hazard assessment of different GDI exhausts using two different cell culture models mimicking the human airway. In addition to gasoline particle filters (GPF), the effects of two lubrication oils with low and high ash content were assessed, since it is known that oils are important contributors to exhaust emissions. Complete exhausts from two gasoline driven cars (GDI1 and GDI2) were applied for 6 h (acute exposure) to a multi-cellular human lung model (16HBE14o-cell line, macrophages, and dendritic cells) and a primary human airway model (MucilAir™). GDI1 vehicle was driven unfiltered and filtered with an uncoated and a coated GPF. GDI2 vehicle was driven under four settings with different fuels: normal unleaded gasoline, 2% high and low ash oil in gasoline, and 2% high ash oil in gasoline with a GPF. GDI1 unfiltered was also used for a repeated exposure (3 times 6 h) to assess possible adverse effects. After 6 h exposure, no genes or proteins for oxidative stress or pro-inflammation were upregulated compared to the filtered air control in both cell systems, neither in GDI1 with GPFs nor in GDI2 with the different fuels. However, the repeated exposure led to a significant increase in HMOX1 and TNFa gene expression in the multi-cellular model, showing the responsiveness of the system towards gasoline engine exhaust upon prolonged exposure. The reduction of particles by GPFs is significant and no adverse effects were observed in vitro during a short-term exposure. On the other hand, more data comparing different lubrication oils and their possible adverse effects are needed. Future experiments also should, as shown here, focus on repeated exposures.

Effects of gasoline and ethanol-gasoline exhaust exposure on human bronchial epithelial and natural killer cells in vitro.

Air pollution exposure, including passenger car emissions, may cause substantial respiratory health effects and cancer death. In western countries, the majority of passenger cars are driven by gasoline fuel. Recently, new motor technologies and ethanol fuels have been introduced to the market, but potential health effects have not been thoroughly investigated. We developed and verified a coculture model composed of bronchial epithelial cells (ECs) and natural killer cells (NKs) mimicking the human airways to compare toxic effects between pure gasoline (E0) and ethanol-gasoline-blend (E85, 85% ethanol, 15% gasoline) exhaust emitted from a flexfuel gasoline car. We drove a steady state cycle, exposed ECs for 6h and added NKs. We assessed exhaust effects in ECs alone and in cocultures by RT-PCR, flow cytometry, and oxidative stress assay. We found no toxic effects after exposure to E0 or E85 compared to air controls. Comparison between E0 and E85 exposure showed a weak association for less oxidative DNA damage after E85 exposure compared to E0. Our results indicate that short-term exposure to gasoline exhaust may have no major toxic effects in ECs and NKs and that ethanol as part of fuel for gasoline cars may be favorable.

Bioethanol Blending Reduces Nanoparticle, PAH, and Alkyl- and Nitro-PAH Emissions and the Genotoxic Potential of Exhaust from a Gasoline Direct Injection Flex-Fuel Vehicle.

Bioethanol as an alternative fuel is widely used as a substitute for gasoline and also in gasoline direct injection (GDI) vehicles, which are quickly replacing traditional port-fuel injection (PFI) vehicles. Better fuel efficiency and increased engine power are reported advantages of GDI vehicles. However, increased emissions of soot-like nanoparticles are also associated with GDI technology with yet unknown health impacts. In this study, we compare emissions of a flex-fuel Euro-5 GDI vehicle operated with gasoline (E0) and two ethanol/gasoline blends (E10 and E85) under transient and steady driving conditions and report effects on particle, polycyclic aromatic hydrocarbon (PAH), and alkyl- and nitro-PAH emissions and assess their genotoxic potential. Particle number emissions when operating the vehicle in the hWLTC (hot started worldwide harmonized light-duty vehicle test cycle) with E10 and E85 were lowered by 97 and 96% compared with that of E0. CO emissions dropped by 81 and 87%, while CO2 emissions were reduced by 13 and 17%. Emissions of selected PAHs were lowered by 67-96% with E10 and by 82-96% with E85, and the genotoxic potentials dropped by 72 and 83%, respectively. Ethanol blending appears to reduce genotoxic emissions on this specific flex-fuel GDI vehicle; however, other GDI vehicle types should be analyzed.

Hazard identification of exhausts from gasoline-ethanol fuel blends using a multi-cellular human lung model.

Ethanol can be produced from biomass and as such is renewable, unlike petroleum-based fuel. Almost all gasoline cars can drive with fuel containing 10% ethanol (E10), flex-fuel cars can even use 85% ethanol (E85). Brazil and the USA already include 10-27% ethanol in their standard fuel by law. Most health effect studies on car emissions are however performed with diesel exhausts, and only few data exists for other fuels. In this work we investigated possible toxic effects of exhaust aerosols from ethanol-gasoline blends using a multi-cellular model of the human lung. A flex-fuel passenger car was driven on a chassis dynamometer and fueled with E10, E85, or pure gasoline (E0). Exhausts obtained from a steady state cycle were directly applied for 6h at a dilution of 1:10 onto a multi-cellular human lung model mimicking the bronchial compartment composed of human bronchial cells (16HBE14o-), supplemented with human monocyte-derived dendritic cells and monocyte-derived macrophages, cultured at the air-liquid interface. Biological endpoints were assessed after 6h post incubation and included cytotoxicity, pro-inflammation, oxidative stress, and DNA damage. Filtered air was applied to control cells in parallel to the different exhausts; for comparison an exposure to diesel exhaust was also included in the study. No differences were measured for the volatile compounds, i.e. CO, NOx, and T.HC for the different ethanol supplemented exhausts. Average particle number were 6×102 #/cm3 (E0), 1×105 #/cm3 (E10), 3×103 #/cm3 (E85), and 2.8×106 #/cm3 (diesel). In ethanol-gasoline exposure conditions no cytotoxicity and no morphological changes were observed in the lung cell cultures, in addition no oxidative stress - as analyzed with the glutathione assay - was measured. Gene expression analysis also shows no induction in any of the tested genes, including mRNA levels of genes related to oxidative stress and pro-inflammation, as well as indoleamine 2,3-dioxygenase 1 (IDO-1), transcription factor NFE2-related factor 2 (NFE2L2), and NAD(P)H dehydrogenase [quinone] 1 (NQO1). Finally, no DNA damage was observed with the OxyDNA assay. On the other hand, cell death, oxidative stress, as well as an increase in pro-inflammatory cytokines was observed for cells exposed to diesel exhaust, confirming the results of other studies and the applicability of our exposure system. In conclusion, the tested exhausts from a flex-fuel gasoline vehicle using different ethanol-gasoline blends did not induce adverse cell responses in this acute exposure. So far ethanol-gasoline blends can promptly be used, though further studies, e.g. chronic and in vivo studies, are needed.

Biofuel-Promoted Polychlorinated Dibenzodioxin/furan Formation in an Iron-Catalyzed Diesel Particle Filter.

Iron-catalyzed diesel particle filters (DPFs) are widely used for particle abatement. Active catalyst particles, so-called fuel-borne catalysts (FBCs), are formed in situ, in the engine, when combusting precursors, which were premixed with the fuel. The obtained iron oxide particles catalyze soot oxidation in filters. Iron-catalyzed DPFs are considered as safe with respect to their potential to form polychlorinated dibenzodioxins/furans (PCDD/Fs). We reported that a bimetallic potassium/iron FBC supported an intense PCDD/F formation in a DPF. Here, we discuss the impact of fatty acid methyl ester (FAME) biofuel on PCDD/F emissions. The iron-catalyzed DPF indeed supported a PCDD/F formation with biofuel but remained inactive with petroleum-derived diesel fuel. PCDD/F emissions (I-TEQ) increased 23-fold when comparing biofuel and diesel data. Emissions of 2,3,7,8-TCDD, the most toxic congener [toxicity equivalence factor (TEF) = 1.0], increased 90-fold, and those of 2,3,7,8-TCDF (TEF = 0.1) increased 170-fold. Congener patterns also changed, indicating a preferential formation of tetra- and penta-chlorodibenzofurans. Thus, an inactive iron-catalyzed DPF becomes active, supporting a PCDD/F formation, when operated with biofuel containing impurities of potassium. Alkali metals are inherent constituents of biofuels. According to the current European Union (EU) legislation, levels of 5 µg/g are accepted. We conclude that risks for a secondary PCDD/F formation in iron-catalyzed DPFs increase when combusting potassium-containing biofuels.

Effects of an iron-based fuel-borne catalyst and a diesel particle filter on exhaust toxicity in lung cells in vitro.

Metal-containing fuel additives catalyzing soot combustion in diesel particle filters are used in a widespread manner, and with the growing popularity of diesel vehicles, their application is expected to increase in the near future. Detailed investigation into how such additives affect exhaust toxicity is therefore necessary and has to be performed before epidemiological evidence points towards adverse effects of their application. The present study investigates how the addition of an iron-based fuel additive (Satacen®3, 40 ppm Fe) to low-sulfur diesel affects the in vitro cytotoxic, oxidative, (pro-)inflammatory, and mutagenic activity of the exhaust of a passenger car operated under constant, low-load conditions by exposing a three-dimensional model of the human airway epithelium to complete exhaust at the air-liquid interface. We could show that the use of the iron catalyst without and with filter technology has positive as well as negative effects on exhaust toxicity compared to exhaust with no additives: it decreases the oxidative and, compared to a non-catalyzed diesel particle filter, the mutagenic potential of diesel exhaust, but increases (pro-)inflammatory effects. The presence of a diesel particle filter also influences the impact of Satacen®3 on exhaust toxicity, and the proper choice of the filter type to be used is of importance with regards to exhaust toxicity. Figure ᅟ.

Test-methods on the test-bench: a comparison of complete exhaust and exhaust particle extracts for genotoxicity/mutagenicity assessment.

With the growing number of new exhaust after-treatment systems, fuels and fuel additives for internal combustion engines, efficient and reliable methods for detecting exhaust genotoxicity and mutagenicity are needed to avoid the widespread application of technologies with undesirable effects toward public health. In a commonly used approach, organic extracts of particulates rather than complete exhaust is used for genotoxicity/mutagenicity assessment, which may reduce the reliability of the results. In the present study, we assessed the mutagenicity and the genotoxicity of complete diesel exhaust compared to an organic exhaust particle extract from the same diesel exhaust in a bacterial and a eukaryotic system, that is, a complex human lung cell model. Both, complete exhaust and organic extract were found to act mutagenic/genotoxic, but the amplitudes of the effects differed considerably. Furthermore, our data indicate that the nature of the mutagenicity may not be identical for complete exhaust and particle extracts. Because in addition, differences between the responses of the different biological systems were found, we suggest that a comprehensive assessment of exhaust toxicity is preferably performed with complete exhaust and with biological systems representative for the organisms and organs of interest (i.e., human lungs) and not only with the Ames test.

PCDD/F formation in an iron/potassium-catalyzed diesel particle filter.

Catalytic diesel particle filters (DPFs) have evolved to a powerful environmental technology. Several metal-based, fuel soluble catalysts, so-called fuel-borne catalysts (FBCs), were developed to catalyze soot combustion and support filter regeneration. Mainly iron- and cerium-based FBCs have been commercialized for passenger cars and heavy-duty vehicle applications. We investigated a new iron/potassium-based FBC used in combination with an uncoated silicon carbide filter and report effects on emissions of polychlorinated dibenzodioxins/furans (PCDD/Fs). The PCDD/F formation potential was assessed under best and worst case conditions, as required for filter approval under the VERT protocol. TEQ-weighted PCDD/F emissions remained low when using the Fe/K catalyst (37/7.5 µg/g) with the filter and commercial, low-sulfur fuel. The addition of chlorine (10 µg/g) immediately led to an intense PCDD/F formation in the Fe/K-DPF. TEQ-based emissions increased 51-fold from engine-out levels of 95 to 4800 pg I-TEQ/L after the DPF. Emissions of 2,3,7,8-TCDD, the most toxic congener (TEF = 1.0), increased 320-fold, those of 2,3,7,8-TCDF (TEF = 0.1) even 540-fold. Remarkable pattern changes were noticed, indicating a preferential formation of tetrachlorinated dibenzofurans. It has been shown that potassium acts as a structural promoter inducing the formation of magnetite (Fe3O4) rather than hematite (Fe2O3). This may alter the catalytic properties of iron. But the chemical nature of this new catalyst is yet unknown, and we are far from an established mechanism for this new pathway to PCDD/Fs. In conclusion, the iron/potassium-catalyzed DPF has a high PCDD/F formation potential, similar to the ones of copper-catalyzed filters, the latter are prohibited by Swiss legislation.

Effects of a combined Diesel particle filter-DeNOx system (DPN) on reactive nitrogen compounds emissions: a parameter study.

The impact of a combined diesel particle filter-deNO(x) system (DPN) on emissions of reactive nitrogen compounds (RNCs) was studied varying the urea feed factor (α), temperature, and residence time, which are key parameters of the deNO(x) process. The DPN consisted of a platinum-coated cordierite filter and a vanadia-based deNO(x) catalyst supporting selective catalytic reduction (SCR) chemistry. Ammonia (NH3) is produced in situ from thermolysis of urea and hydrolysis of isocyanic acid (HNCO). HNCO and NH3 are both toxic and highly reactive intermediates. The deNO(x) system was only part-time active in the ISO8178/4 C1cycle. Urea injection was stopped and restarted twice. Mean NO and NO2 conversion efficiencies were 80%, 95%, 97% and 43%, 87%, 99%, respectively, for α = 0.8, 1.0, and 1.2. HNCO emissions increased from 0.028 g/h engine-out to 0.18, 0.25, and 0.26 g/h at α = 0.8, 1.0, and 1.2, whereas NH3 emissions increased from <0.045 to 0.12, 1.82, and 12.8 g/h with maxima at highest temperatures and shortest residence times. Most HNCO is released at intermediate residence times (0.2-0.3 s) and temperatures (300-400 °C). Total RNC efficiencies are highest at α = 1.0, when comparable amounts of reduced and oxidized compounds are released. The DPN represents the most advanced system studied so far under the VERT protocol achieving high conversion efficiencies for particles, NO, NO2, CO, and hydrocarbons. However, we observed a trade-off between deNO(x) efficiency and secondary emissions. Therefore, it is important to adopt such DPN technology to specific application conditions to take advantage of reduced NO(x) and particle emissions while avoiding NH3 and HNCO slip.

Cerium dioxide nanoparticles can interfere with the associated cellular mechanistic response to diesel exhaust exposure.

The aim of this study was to compare the biological response of a sophisticated in vitro 3D co-culture model of the epithelial airway barrier to a co-exposure of CeO(2) NPs and diesel exhaust using a realistic air-liquid exposure system. Independent of the individual effects of either diesel exhaust or CeO(2) NPs investigation observed that a combined exposure of CeO(2) NPs and diesel exhaust did not cause a significant cytotoxic effect or alter cellular morphology after exposure to diesel exhaust for 2h at 20µg/ml (low dose) or for 6h at 60µg/ml (high dose), and a subsequent 6h exposure to an aerosolized solution of CeO(2) NPs at the same doses. A significant loss in the reduced intracellular glutathione level was recorded, although a significant increase in the oxidative marker HMOX-1 was found after exposure to a low and high dose respectively. Both the gene expression and protein release of tumour necrosis factor-α were significantly elevated after a high dose exposure only. In conclusion, CeO(2) NPs, in combination with diesel exhaust, can significantly interfere with the cell machinery, indicating a specific, potentially adverse role of CeO(2) NPs in regards to the biological response of diesel exhaust exposure.

Effects of sodium butyrate and salinomycin upon intestinal microbiota, mucosal morphology and performance of broiler chickens.

The effect of dietary sodium butyrate (SB) or salinomycin (SAL) or both additives on performance, small intestinal morphology and microbial ecology of broiler chickens was studied. A growth trial was conducted with 96 Ross 308 female broilers from 1 to 30 days of age. Four treatment groups were fed with a non-supplemented control diet or three experimental diets supplemented with i) 300 mg SB (Adimix 30 coated) per kg, ii) 60 mg SAL (Sacox) per kg or iii) both additives in combination. Feed intake and body-weight gain decreased and gain-to-feed ratio increased due to SAL supplementation, while addition of SB did not affect performance in comparison with the control diet but positively affected feed intake and body-weight gain in comparison with birds fed the SAL-supplemented diet. Villus height in jejunum decreased, while crypt depth increased due to SAL supplementation. Addition of SB increased crypt depth in jejunum. No significant effect of either additive was observed in ileum morphology. Total short-chain organic acids concentration in ileal digesta decreased with SAL supplementation, mainly due to lower lactic acid concentration, but no effects were observed in the caeca. The SAL supplementation was accompanied by a pH increase in ileum and a pH decrease in caecum. No significant effect of SB addition was observed for these parameters. Total bacterial numbers and Lactobacillus [lactic acid bacteria (LAB)] counts in ileal and caecal contents were lower in birds fed with SAL-supplemented diet in comparison with birds fed with control or SB diet. DNA fingerprints revealed SAL supplementation to affect the microbial population by suppressing dominating LAB, potentially L. aviarius. The presented results show that dietary SAL, supplemented alone or in combination with SB, suppressed the microbial activity and altered the microbial community structure mainly in ileum. SAL alone negatively affected feed intake and body-weight gain; however, the effect was ameliorated by SB supplementation.

New exposure system to evaluate the toxicity of (scooter) exhaust emissions in lung cells in vitro.

A constantly growing number of scooters produce an increasing amount of potentially harmful emissions. Due to their engine technology, two-stroke scooters emit huge amounts of adverse substances, which can induce adverse pulmonary and cardiovascular health effects. The aim of this study was to develop a system to expose a characterized triple cell coculture model of the human epithelial airway barrier, to freshly produced and characterized total scooter exhaust emissions. In exposure chambers, cell cultures were exposed for 1 and 2 h to 1:100 diluted exhaust emissions and in the reference chamber to filtered ambient air, both controlled at 5% CO(2), 85% relative humidity, and 37 degrees C. The postexposure time was 0-24 h. Cytotoxicity, used to validate the exposure system, was significantly increased in exposed cell cultures after 8 h postexposure time. (Pro-) inflammatory chemo- and cytokine concentrations in the medium of exposed cells were significantly higher at the 12 h postexposure time point. It was shown that the described exposure system (with 2 h exposure duration, 8 and 24 h postexposure time, dilution of 1:100, flow of 2 L/min as optimal exposure conditions) can be used to evaluate the toxic potential of total exhaust emissions.

Impact of low- and high-oxidation diesel particulate filters on genotoxic exhaust constituents.

Diesel exhaust contains several genotoxic compounds that may or may not penetrate diesel particulate filters (DPFs). Furthermore, the DPF-supported combustion of soot and adsorbed compounds may lead to the formation of additional pollutants. Herein, we compare the impact of 14 different DPFs on emissions of known genotoxic compounds. During a four year period, these DPFs were tested on a heavy duty diesel engine, operated in the ISO 8178/4 C1 cycle. Integral samples, including gas-phase and particle-bound matter were taken. All DPFs were efficient wall-flow filters with solid particulate number filtration efficiencies eta > 98%. On the basis of their CO, NO, and NO(2) emission characteristics, two different filter families were distinguished. DPFs with high oxidation potential (hox, n = 8) converted CO and NO besides hydrocarbons, whereas low oxidation potential DPFs (lox, n = 6) did not support CO and NO oxidation but still converted hydrocarbons. Lox-DPFs reduced NO(2) from 1.0 +/- 0.3 (engine-out) to 0.42 +/- 0.11 g/kWh (eta = 0.59), whereas hox-DPFs induced a NO(2) formation up to 3.3 +/- 0.7 g/kWh (eta = -2.16). Emissions of genotoxic PAHs decreased for both filter families. Conversion efficiencies varied for individual PAHs and were lower for lox- (eta = 0.31-0.87) than for hox-DPFs (eta = 0.75-0.98). Certain nitro-PAHs were formed indicating that nitration is an important step along PAH oxidation. For example, 1-nitronaphthalene emissions increased from 11 to 17 to 21 microg/L without, with lox-, and hox-DPFs respectively, whereas 2-nitronaphthalene emissions decreased from 25 to 19 to 4.7 microg/L. In contrast to our expectations, the nitration potential of lox-DPFs was higher than the one of hox-DPFs, despite the intense NO(2) formation of the latter. The filters converted most genotoxic PAHs and nitro-PAHs and most soot particles, acting as carriers for these compounds. Hox-DPF exhaust remains oxidizing and therefore is expected to support atmospheric oxidation reactions, whereas lox-DPF exhaust is reducing and consuming oxidants such as ozone, when mixed with ambient air.

Secondary effects of catalytic diesel particulate filters: conversion of PAHs versus formation of nitro-PAHs.

Diesel particulate filters (DPFs) are a promising technology to detoxify diesel exhaust. However, the secondary combustion of diesel soot and associated compounds may also induce the formation of new pollutants. Diesel soot is rated as carcinogenic to humans and also acts as a carrier for a variety of genotoxic compounds such as certain polycyclic aromatic hydrocarbons (PAHs) or nitrated PAHs (nitro-PAHs). Furthermore, diesel exhaust contains considerable amounts of nitric oxide (NO), which can be converted to more powerful nitrating species like nitrogen dioxide (NO2), nitric acid (HNO3), and others. This mix of compounds may support nitration reactions in DPFs. Herein we report effects of two cordierite-based, monolithic, wall-flow DPFs on emissions of genotoxic PAHs and nitro-PAHs and compare these findings with those of a reporter gene bioassay sensitive to aryl hydrocarbons (AHs). Soot combustion was either catalyzed with an iron- or a copper/iron-based fuel additive (fuel-borne catalysts). A heavy duty diesel engine, operated according to the 8-stage ISO 8178/4 C1 cycle, was used as test platform. Emissions of all investigated 4- to 6-ring PAHs were reduced by about 40-90%, including those rated as carcinogenic. Emissions of 1- and 2-nitronaphthalene increased by about 20-100%. Among the 3-ring nitro-PAHs, emissions of 3-nitrophenanthrene decreased by about 30%, whereas 9-nitrophenanthrene and 9-nitroanthracene were found only after DPFs. In case of 4-ring nitro-PAHs, emissions of 3-nitrofluoranthene, 1-nitropyrene, and 4-nitropyrene decreased by about 40-60% with DPFs. Total AH-receptor (AHR) agonist concentrations of diesel exhaust were lowered by 80-90%, when using the iron- and copper-based DPFs. The tested PAHs accounted for < 1% of the total AHR-mediated response, indicating that considerable amounts of other aryl hydrocarbons must be present in filtered and unfiltered exhaust. We conclude that both DPFs detoxified diesel exhaust with respect to total aryl hydrocarbons, including the investigated carcinogenic PAHs, but we also noticed a secondary formation of selected nitro-PAHs. Nitration reactions were found to be stereoselective with a preferential substitution of hydrogen atoms at peri-positions. The stereoisomers obtained are related to combustion chemistry, but differ from those formed upon atmospheric nitration of PAHs.

Secondary effects of catalytic diesel particulate filters: copper-induced formation of PCDD/Fs.

Potential risks of a secondary formation of polychlorinated dibenzodioxins/furans (PCDD/Fs) were assessed for two cordierite-based, wall-through diesel particulate filters (DPFs) for which soot combustion was either catalyzed with an iron- or a copper-based fuel additive. A heavy duty diesel engine was used as test platform, applying the eight-stage ISO 8178/4 C1 cycle. DPF applications neither affected the engine performance, nor did they increase NO, NO2, CO, and CO2 emissions. The latter is a metric for fuel consumption. THC emissions decreased by about 40% when deploying DPFs. PCDD/F emissions, with a focus on tetra- to octachlorinated congeners, were compared under standard and worst case conditions (enhanced chlorine uptake). The iron-catalyzed DPF neither increased PCDD/F emissions, nor did it change the congener pattern, even when traces of chlorine became available. In case of copper, PCDD/F emissions increased by up to 3 orders of magnitude from 22 to 200 to 12 700 pg I-TEQ/L with fuels of < 2, 14, and 110 microg/g chlorine, respectively. Mainly lower chlorinated DD/Fs were formed. Based on these substantial effects on PCDD/F emissions, the copper-catalyzed DPF system was not approved for workplace applications, whereas the iron system fulfilled all the specifications of the Swiss procedures for DPF approval (VERT).