Visualization of the granule temperature using thermal imaging to improve understanding of the granulation mechanism in continuous twin-screw melt granulation.

The aim of this study is to increase process understanding of the granulation mechanism in twin-screw melt granulation by evaluating the influence of different screw configurations on granule formation and granule temperature via thermal imaging. The study used a Design of Experiments (DoE) to process a miscible and immiscible formulation (85% API/binder w/w) using a twin-screw extruder with varying screw configurations. The barrel temperature (°C), screw speed (rpm), throughput (kg/h), and kneading zone (direction and stagger angle) were varied. Granule and process properties were evaluated for samples collected at four different locations along the length of the granulation barrel to visualize the granule formation, and granule temperature was monitored by an infrared camera to measure heat transfer on the granules. The resulting temperature was linked to the granule properties and the granule formation along the length of the barrel. The most influencing factors on the granule temperature are the direction of the kneading zone and the set barrel temperature. It was observed that granule formation mainly occurred in the zones that apply more kneading on the granules. The highest temperature increase was observed when the smallest stagger angle in reverse configuration was used, and could be linked to better granule quality attributes.

The application of Near-Infrared Spatially Resolved Spectroscopy in scope of achieving continuous real-time quality monitoring and control of tablets with challenging dimensions.

In scope of achieving real-time release of tablets, quality attributes need to be monitored and controlled through Process Analytical Technology tools such as near-infrared spectroscopy (NIRS). The authors evaluated the suitability of NIR-Spatially Resolved Spectroscopy (NIR-SRS) for continuous real-time monitoring and control of content uniformity, hardness and homogeneity of tablets with challenging dimensions. A novel user-friendly research and development inspection unit was used as standalone equipment for the analysis of small oblong tablets with deep-cut break lines. A total of 66 tablets varying in hardness and Active Pharmaceutical Ingredient (API) content were inspected, with each tablet being analysed five times and measurements repeated on three different days. Partial Least Squares (PLS) models were developed to assess content uniformity and hardness, of which the former showed higher accuracy. The authors attempted to visualize tablet homogeneity through NIR-SRS spectra by regressing all spectra obtained during a single measurement using a content uniformity PLS model. The NIR-SRS probe demonstrated its potential towards real-time release testing through its ability to quickly monitor content uniformity, hardness and visualize homogeneity, even for tablets with challenging dimensions.

Elucidation of granulation mechanisms along the length of the barrel in continuous twin-screw melt granulation.

In the pharmaceutical industry, innovative continuous manufacturing technologies such as twin-screw melt granulation (TSMG) are gaining more and more interest to process challenging formulations. To enable the implementation of TSMG, more elucidation of the process is required and this study provides a better understanding of the granule formation along the length of the barrel. By sampling at four different zones, the influence of screw configuration, process parameters and formulation is investigated for the granule properties next to the residence time distribution. It showed that conveying elements initiate the granulation by providing a limited heat transfer into the powder bed. In the kneading zones, the consolidation stage takes place, shear elongation combined with breakage and layering is occurring for the reversed configurations and densification with breakage and layering for the forward and neutral configurations. Due to the material build-up in the reversed configurations, these granules are larger, stronger, more elongated and less porous due to the higher degree of shear and densification. This configuration also shows a significantly longer residence time compared to the forward configuration. Hence, the higher level of shear and the longer period of time enables more melting of the binder resulting in successful granulation.

Elucidation of the powder flow pattern in a twin-screw LIW-feeder for various refill regimes.

The importance of residence time distribution modeling is acknowledged as a tool for enabling material tracking and control within a continuous manufacturing line in order to safeguard both product quality and production efficiency. One of the first unit-operations into a continuous direct compression line (i.e. CDC-line) worthwhile doing extensive RTD-analysis upon are the LIW-feeders since they dose the ingredients in a controlled way following the label claim and hence can directly influence critical quality attributes like content uniformity. An NIR measurement method was developed determining the RTD of selected powders at specific feeder settings. Step-change experiments using sodium saccharin as a tracer were conducted. In order to gain and in depth understanding of the material flow, spatial samples throughout the hopper were taken at predefined timepoints during the step change experiments. This revealed the presence of a bypass trajectory along the edges of the agitator, while in the center of the agitator an inner mixing volume in which the tracer concentration lags behind seemed to be present. Finally, a model based on a plug flow and continuous stirred tank reactor was evaluated. The fitted model was not able to capture this complex flow behavior and shows the need for an extended compartmental model distinguishing between a bypass trajectory formed by the agitator and an inner mixing volume.

Identification of continuous twin-screw melt granulation mechanisms for different screw configurations, process settings and formulation.

Twin-screw melt granulation (TSMG) is a promising continuous manufacturing technology for the processing of high drug load formulations and to formulate heat- and moisture-sensitive active pharmaceutical ingredients (APIs). This study evaluates the influence of process parameters for TSMG, mainly focusing on the effect of the screw configuration combined with screw speed, throughput and barrel temperature, to elucidate the melt granulation mechanisms. For the kneading zone, the stagger angle was varied between 30°, 60° and 90°, and investigated for both the forward and the reversed direction. In addition to the process parameters, the influence of the formulation differing in their API-binder miscibility was evaluated. As responses, the granule (size, friability and porosity) and process properties such as torque were evaluated, indicating that the screw configuration is the most influential factor. Nucleation, consolidation and breakage are the granulation mechanisms for the forward and the neutral configuration, while consolidation and densification with shear elongation are identified for the reversed configuration. The formulations differ mainly in the forward and neutral configuration since the immiscible formulation shows a bimodal granule size distribution with a larger fraction of fines and weaker granules is obtained. For the reversed configuration, similar granulation mechanisms are seen for both formulations.

Continuous direct compression: Development of an empirical predictive model and challenges regarding PAT implementation.

In this study, an empirical predictive model was developed based on the quantitative relationships between blend properties, critical quality attributes (CQA) and critical process parameters (CPP) related to blending and tableting. The blend uniformity and API concentration in the tablets were used to elucidate challenges related to the processability as well as the implementation of PAT tools. Thirty divergent ternary blends were evaluated on a continuous direct compression line (ConsiGma™ CDC-50). The trials showed a significant impact of the impeller configuration and impeller speed on the blending performance, whereas a limited impact of blend properties was observed. In contrast, blend properties played a significant role during compression, where changes in blend composition significantly altered the tablet quality. The observed correlations allowed to develop an empirical predictive model for the selection of process configurations based on the blend properties, reducing the number of trial runs needed to optimize a process and thus reducing development time and costs of new drug products. Furthermore, the trials elucidated several challenges related to blend properties that had a significant impact on PAT implementation and performance of the CDC-platform, highlighting the importance of further process development and optimization in order to solve the remaining challenges.

In-depth analysis of the long-term processability of materials during continuous feeding.

This study determined the feasibility of long-term continuous powder feeding and its effect on the overall process performance. Additionally, quantitative relationships were established between material properties, process settings and screw feeding responses during gravimetric feeding. Twelve divergent raw materials were processed over longer periods using a GEA Compact Feeder integrated in a continuous direct compression line (ConsiGma™ CDC-50). The resulting gravimetric feeding responses were combined with the material properties and process settings into an overall PLS model. The model elucidated the impact of the material descriptors for density; powder flow; particle size; compressibility; permeability and wall friction angle on the feeding process. Furthermore, long-term processing of the materials exhibited challenges related to the processability and refill consistency where a significant impact of the compressibility and cohesive/adhesive properties of the materials was observed. Overall, this approach provided insights into the feasibility of long-term continuous feeding which is not possible through 'short-term' feeding trials. Additionally, throughout this study, the need for material-specific adjustments of the feeding and refill equipment was highlighted.

The effect of binder types on the breakage and drying behavior of granules in a semi-continuous fluid bed dryer after twin screw wet granulation.

Current study investigated the effect of different binder types on the granule drying process and the granule breakage behavior in a semi-continuous fluid bed dryer integrated in the C25 ConsiGma-system. The studied binders (i.e. hydroxypropyl pea starch, hydroxypropyl methylcellulose E15, polyvinylpyrrolidone K12, and starch octenyl succinate CO 01) required different liquid amounts to produce similar granule quality. These different liquid requirements were translated into different drying conditions for each binder to result in sufficiently dry granules at the end of a drying cycle. By comparing the size distribution of the granules before entering and after exiting the fluid bed dryer, granule breakage could be evaluated. No effect of the binder type on the granule breakage during drying was observed. However, differences in granule breakage were observed for the binders when processed with the horizontal set-up of the C25 system, as granule breakage during pneumatic transport depended on the binder type. Only one binder (hydroxypropyl pea starch) allowed to avoid granule breakage during the entire process. Furthermore, this research showed that the drying process was mainly steered by the liquid requirements for granulation, and that these liquid requirements depended on the binder used.

TPLS as predictive platform for twin-screw wet granulation process and formulation development.

In recent years, the interest in continuous manufacturing techniques, such as twin-screw wet granulation, has increased. However, the understanding of the influence of the combination of raw material properties and process settings upon the granule quality attributes is still limited. In this study, a T-shaped partial least squares (TPLS) model was developed to link raw material properties, the ratios in which these raw materials were combined and the applied process parameters for the twin-screw wet granulation process with the granule quality attributes. In addition, the predictive ability of the TPLS model was used to find a suitable combination of formulation composition and twin-screw granulation process settings for a new API leading to desired granule quality attributes. Overall, this study helped to better understand the link between raw material properties, formulation composition and process settings on granule quality attributes. Moreover, as TPLS can provide a reasonable starting point for formulation and process development for new APIs, it can reduce the experimental development efforts and consequently the consumption of expensive (and often limited available) new API.

Evaluation of torque as an in-process control for granule size during twin-screw wet granulation.

The potential of torque as in-process control (IPC) to monitor granule size in twin-screw wet granulation (TSG) was investigated. An experimental set-up allowing the collection of granules at four different locations (i.e., in the wetting zone, after the first and second kneading zone and at the end of the granulator) of the granulator screws was used to determine the change in granule size, granule temperature and the contribution of each compartment to the overall torque for varying screw speed, mass feed rate and liquid-to-solid ratio. The only observed correlation was between the granule size and torque increase after the first kneading zone because the torque increase was an indication of the degree in granule growth which was consistently observed with all applied granulation process parameters. No correlation was observed in the other locations as changes of torque were accompanied to either granule breakage and/or growth. Moreover, torque increase was correlated to higher granule temperature, suggesting that energy put into the granulator was partly used to heat up the material being processed and explains additionally the lack of correlation between granule size and torque. Therefore, this study showed that torque could not be used as IPC to monitor granule size during TSG.

Determination of a quantitative relationship between material properties, process settings and screw feeding behavior via multivariate data-analysis.

In this study, a quantitative relationship between material properties, process settings and screw feeding responses of a high-throughput feeder was established via multivariate models (PLS). Thirteen divergent powders were selected and characterized for 44 material property descriptors. During volumetric feeder trials, the maximum feed capacity (FCCmax), the relative standard deviation on the maximum feed capacity (RSDFCmax), the short term variability (STRSD) and feed capacity decay (FCdecay) were determined. The gravimetric feeder trials generated values for the mass flow rate variability (RSDLC), short term variability (STRSD) and refill responses (Vrefill and RSDrefill). The developed PLS models elucidated that the material properties and process settings were clearly correlated to the feeding behavior. The extended volumetric feeder trials pointed out that there was a significant influence of the chosen screw type and screw speed on the feeding process. Furthermore, the process could be optimized by reducing the feeding variability through the application of optimized mass flow filters, high frequency vibrations, independent agitator control and optimized top-up systems. Overall, the models could allow the prediction of the feeding performance for a wide range of materials based on the characterization of a subset of material properties greatly reducing the number of required feeding experiments.

A primary drying model-based comparison of conventional batch freeze-drying to continuous spin-freeze-drying for unit doses.

An innovative continuous spin-freeze-drying technology for unit doses was recently developed. For this technology, a mechanistic primary drying model was developed allowing the calculation of the optimal dynamic drying trajectory for spin-frozen formulations. In this work, a model-based and experimentally verified comparison was made between conventional batch freeze-drying and spin-freeze-drying by analyzing the outputs (i.e., primary drying endpoint, optimal shelf temperature/power heater and product temperature profile) of both primary drying models. Input parameters such as dried product layer resistance (Rp) and heat input parameters (Kv,Ptot) were experimentally determined for both freeze-drying methods and compared. In addition, optimal dynamic process parameters were calculated for 3 model formulations by using both mechanistic models. Finally, model predictions were validated by measuring the product temperature and primary drying endpoint. It was observed that, when considering the same layer thickness, Rp was generally lower for continuous spin-frozen formulations compared to vials frozen in a conventional batch freeze-dryer. This observation contributes to the short primary drying times of spin-frozen formulations. In addition, as spin-freezing drastically increases the surface area of the product and lowers the dried layer thickness, drying times can be reduced even further while an excellent cake structure and appearance can still be obtained. The primary drying model for spin-frozen formulations proved to be equally accurate for the prediction of the primary drying endpoint and product temperature compared to the batch freeze-drying model.

Screening of pharmaceutical polymers for extrusion-Based Additive Manufacturing of patient-tailored tablets.

The main objective of this work was to explore the potential of coupling hot-melt extrusion (HME) to Fused Filament Fabrication (FFF), also known as Extrusion-Based Additive Manufacturing (EBAM) or 3D Printing, in order to manufacture 3D printed tablets with different release behavior from plasticizer-free filament matrices. The suitability of different thermoplastic polymers towards FFF was investigated, and a link between the mechanical properties of filaments produced by HME and the feeding performance into the FFF printer was established. Model drugs with different aqueous solubility (metoprolol tartrate and theophylline anhydrous) were processed with hydrophilic and hydrophobic polymers, and the influence of the formulation, drug concentration and applied process settings on the release kinetics was investigated. Filaments with up to 40% drug load were successfully extruded with a smooth surface and a diameter of 1.75 ± 0.05 mm. However, filaments with high brittleness and low toughness were broken by the feeding gears. In contrast, none of the filaments were squeezed aside by the gears, which indicated that they were sufficiently stiff as indicated by the high Young's moduli of all formulations. For all formulations, the release from the tablets with 50% infill degree was faster as compared to the tablets with 100% infill degree. Theophylline (20% w/w) release from Kollicoat® IR matrix was completed within 40 min from 50% infill tablets. In contrast, 80% metoprolol tartrate was released from the hydrophobic Capa® 6506 polymer within 24hrs from 50% infill 3D tablets containing 40% w/w MPT.

Influence of binder attributes on binder effectiveness in a continuous twin screw wet granulation process via wet and dry binder addition.

The effect of a wide variety of binders on the quality of granules produced via continuous twin screw wet granulation was studied. Anhydrous dicalcium phosphate was used as poorly soluble filler and was granulated applying dry or wet addition of binders. Furthermore, dry and wet binder characteristics were determined and linked to the binder effectiveness. PVA 4-88 and starch octenyl succinate exhibited the lowest granule friability at low liquid-to-solid ratios, i.e. the highest binder effectiveness, which was attributed to fast binder activation based on the fast wetting kinetics of the binder, to efficient wetting of DCP particles, and to good spreading in the powder bed. The performance of wettability measurements in an early formulation development stage is therefore considered highly important. Additionally, an increased stickiness of the binder surface caused by high binder viscosity and slow dissolution kinetics also positively influenced the binder effectiveness. In conclusion, this study revealed which binder attributes have a critical impact on the granulation process of dicalcium phosphate. Additionally, dry binder addition proved successful for creation of high quality granules.

In-line temperature measurement to improve the understanding of the wetting phase in twin-screw wet granulation and its use in process development.

Wetting is the initial stage of wet granulation processes during which the first contact between the powder and the liquid occurs. Wetting is a critical step to allow granule growth and consolidation, but also to ensure uniform active pharmaceutical ingredient (API) distribution over all granule size fractions. A physical understanding of the wetting stage is therefore crucial to design a robust granulation process. In twin-screw granulation, wetting is physically separated from granule consolidation, growth, breakage and attrition. The present study used this particularity to investigate the wetting step in such a way that the fundamental mechanisms governing the wetting can be linked and understood. A modified granulator barrel was used allowing the collection of granules immediately after the wetting. A low drug-loaded pharmaceutical formulation containing a poorly soluble and poorly wettable API was used for this investigation. Granules obtained after the wetting zone were analysed for granule size distribution, API distribution over the different size fractions and granule temperature. It was found that "wetting efficiency" (i.e., fraction of powder being nucleated during the wetting stage) could be predicted using an energy balance based on in-line measurement of the granule temperature. Wetting efficiency could moreover be linked to final granule quality attributes (i.e., granule size distribution) at the outlet of the granulator. It was further demonstrated that granule growth and consolidation could only be achieved when complete wetting was achieved in the wetting zone of the granulator. This study suggested a methodology based on in-line temperature measurements to quickly determine wetting efficiency. The described methodology could therefore be used as a tool to gain more fundamental understanding of the wetting stage during twin-screw granulation as well as to define suitable formulation and process ranges for further granulation process development.

Viscosity of API/fatty acid suspensions: Pitfalls during analysis.

This article describes how to obtain reliable data during rheological analysis of active pharmaceutical ingredient/fatty acid suspensions. These materials are specifically used for prilling, an innovative pharmaceutical technique for the production of a multiparticulate dosage form. Nevertheless, presented guidelines are applicable for a wide range of pharmaceutical suspensions. Reliable rheological results can only be obtained when being aware of artefacts, such as a non-continuous medium, sedimentation, apparent wall slip and protrusion flow. To comply with the continuum hypothesis at high phase volumes (≥25% w/w), the required gap-to-particle-size ratio may be larger than the generally accepted 10:1 ratio. Reproducible flow curves that are not disturbed by sedimentation during sample analysis can be obtained faster by varying the shear rate stepwise from high to low values. While apparent wall slip (at low shear rates) can be prevented via serrated instead of smooth plates, protrusion flow (at high shear rates) during measurements with serrated plates results in non-reliable data. Therefore, in general, high viscous suspensions with yield stress can be analysed with serrated plates, while low viscous suspensions without yield stress should be analysed with geometries having smooth surfaces. By following these guidelines, accurate rheological properties of pharmaceutical suspensions can be obtained.

Delta-mannitol to enable continuous twin-screw granulation of a highly dosed, poorly compactable formulation.

In current study, it was investigated if the moisture-mediated polymorphic transition from δ- to ß-mannitol during twin screw granulation (TSG) also took place in high drug loaded formulations and if the specific granule morphology associated with the polymorphic transition could enable tableting of granules comprising 75% paracetamol, a poorly compactable drug. Experiments were performed on an integrated continuous manufacturing line, including a twin screw granulator, fluid bed dryer, mill and tablet press. The polymorphic transition of δ- to ß-mannitol was observed during twin screw granulation and granules exhibited the needle-shaped morphology, typical of this transition. TSG at low liquid-to-solid (L/S) ratios and use of polyvinylpyrrolidone or hydroxypropylmethylcellulose as binders inhibited the polymorphic transition, whereas screw speed, drying time, drying temperature and airflow did not affect the solid state of mannitol in the granules. Without binder and despite the high paracetamol drug load in the formulation, limited breakage and attrition was observed during drying and milling. In contrast to granules manufactured from a formulation containing paracetamol/ß-mannitol which could not be tableted due to extensive capping, granules prepared from a paracetamol/δ-mannitol formulation showed good tabletability. In conclusion, δ-mannitol is a promising TSG excipient, especially for high drug-loaded formulations with poor tabletability.

Prilling of API/fatty acid suspensions: Screening of additives for drug release modification.

Current study screened additives which could modify the drug release from prills made of an active pharmaceutical ingredient/fatty acid (API/FA) suspension, without negatively influencing the processability and/or stability of the formulation. Therefore, 11 additives (i.e. emulsifiers, pore-formers and FA-based lubricants) were added in a 20% concentration to a paracetamol/behenic acid formulation. Two additives, Kolliphor® P338 and P407 provided complete drug release in less than 1 h, as their thermoreversible gel formation resulted in a disintegration of the prills. Lower Kolliphor® P338 or P407 concentrations (2.5-10%) resulted in a complete but slower drug release in 24 h as the prills no longer disintegrated and the release mechanism was dominated by pore-formation. Prills with a robust drug release profile (i.e. independent of pH and surfactant concentration of the dissolution medium) were obtained after the addition of ≥5% Kolliphor® P338 or P407 to the FA-based formulation. Based on a 6-month stability study, it was concluded that Kolliphor® P407 was a suitable additive to modify the drug release profile of API/FA suspension-based prills when formulations were stored below 25 °C at low relative humidity.

Prilling of API/fatty acid suspensions: Processability and characterisation.

Current study evaluated the processability and characteristics of prills made of an active pharmaceutical ingredient/fatty acid (API/FA) suspension instead of previously studied API/FA solutions to enlarge the application field of prilling. Metformin hydrochloride (MET) and paracetamol (PAR) were used as model APIs while both the effect of drug load (10-40%) and FA chain length (C14-C22) were evaluated. API/FA suspensions were processable on lab-scale prilling equipment without thermal degradation, nozzle obstruction or sedimentation in function of processing time. The collected prills were spherical (AR ≥ 0.898) with a smooth surface (sphericity ≥ 0.914) and a particle size of ±2.3 mm and 2.4 mm for MET and PAR prills, respectively, independent of drug load and/or FA chain length. In vitro drug release evaluation revealed a faster drug release at higher drug load, higher API water solubility and shorter FA chain length. Solid state characterisation via XRD and Raman spectroscopy showed that API and FA crystallinity was maintained after thermal processing via prilling and during storage. Evaluation of the similarity factor indicated a stable drug release (f2 > 50) from MET and PAR prills after 6 months storage at 25 °C or 40 °C.

Managing API raw material variability in a continuous manufacturing line - Prediction of process robustness.

Many studies on continuous twin-screw granulation only focus on the granulator without linking this process step to the upstream and downstream unit operations. Product critical quality attributes (CQAs) are however not only determined by the granulation step. In this study, the possibility to manage the batch-to-batch variability of an active pharmaceutical ingredient (API) in a high drug loaded formulation on a continuous line was investigated to obtain consistent tablet CQAs. As the ultimate goal of continuous manufacturing is to produce 24/7, current study also aimed at guaranteeing long term stability of the process. To do so, previously identified API critical material attributes (CMAs) were varied together with granulation, drying and milling critical process parameters (CPPs) in a screening design of experiments to understand the influence of these factors upon product CQAs and process stability. To evaluate the factors affecting the process stability with a reduced amount of materials, process deviations recorded by process sensors were used. While product CQAs only depended on process CPPs, process stability was strongly affected by API CMAs. The effect of API batch-to-batch variability on process stability could nonetheless be managed by applying suitable granulation conditions. Therefore, appropriate ranges of CPPs were defined to ensure both product CQAs and process stability. By studying the fully integrated continuous manufacturing line, it was possible to highlight the interactions between the different unit operations and the API CMAs and to design a robust process.