RESUMO
Because of stress shielding effects, traditional titanium (Ti) alloy scaffolds have a high elastic modulus, which might promote looseness and bone disintegration surrounding the implant, increasing the likelihood of a second surgery. In contrast, 3D-printed porous Ti alloy scaffolds can reduce the scaffold weight while enhancing biocompatibility. Further, these scaffolds' porous nature allows bone tissue ingrowth as well as strong pore connectivity, which can improve nutrient absorption. Nevertheless, bare Ti alloy implants may fail because of inadequate bone integration; hence, adding a coating on the implant surface is an effective technique for improving implant stability. In this study, a composite coating comprising hydroxyapatite (HAP), chitosan (CS), tannic acid (TA) and copper ions (Cu2+) (Cu2+/TA/HAP composite coating) was prepared on the surface of 3D printed porous Ti alloy scaffolds using electrophoretic deposition. Using the standard plate count method, Live/Dead bacteria staining assay, FITC Phalloidin and 4',6-diamidino-2-phenylindole staining assay, and live/dead staining of cells we determined that the composite coating has better antibacterial properties and cytocompatibility as well as lower cytotoxicity. The Alkaline Phosphatase assay revealed that the coating results showed good osteogenesis potential. Overall, the composite coatings produced in this investigation give new potential for the application of Ti alloys in clinics.
RESUMO
BACKGROUND:Bone mineral density is the clinical gold standard for determining bone strength,but bone mineral density is less sensitive to changes in bone mass,with large changes in bone mineral density only occurring when bone mass is significantly reduced,so bone mineral density has limited ability to predict changes in bone strength and fracture risk. OBJECTIVE:A model of the normal and osteoporotic hip joint was developed to analyze the stresses and deformation in the hip of normal and osteoporotic patients under single-leg standing conditions. METHODS:A healthy adult female volunteer at the age of 36 years was selected as the study subject.The CT data of the hip joint of this volunteer were obtained and saved in DICOM format.The hip joint model was reconstructed in three dimensions,and the material properties were assigned by the gray value assignment method to obtain the normal and osteoporotic hip joint models according to the empirical formula.The same boundary conditions and loads were set to simulate the stresses and deformation in the normal and osteoporotic hip joints in the single-leg standing position. RESULTS AND CONCLUSION:(1)In the finite element model of the normal and osteoporotic hip,the stress distribution was more concentrated in the medial region of the femoral neck.(2)In the hip bone,the stress distribution was mainly concentrated in the upper part of the acetabulum.(3)The stress peaks in the medial femoral neck and upper acetabulum were larger in the normal hip model than in the osteoporotic hip model,probably due to the reduced bone strength of the osteoporotic bone.(4)The peak Von Mises of both normal and osteoporotic hip models were concentrated on the medial femoral neck,and the peak Von Mises of the hip bone was smaller,indicating that the overall effect of osteoporosis on hip bone stresses was relatively small.(5)In terms of deformation in the single-leg standing position,the maximum deformation in the normal hip model was located at the acetabulum and femoral head,and the maximum deformation was located at the upper part of the greater trochanter of the femur.(6)It is suggested that the finite element analysis method to model the values of parameters related to bone tissue in osteoporosis may improve clinical prediction of bone strength changes and fracture risk.It is explained from the biomechanical view that the intertrochanteric femur and femoral neck are good sites for osteoporotic hip fractures.
RESUMO
Objective:To investigate the effect of 3D-printed customized flanged cup in hip revision with severe acetabular bone defects.Methods:Since February 2017, 10 cases of 3D-printed customized flanged cups were used in hip revision with severe acetabular bone defects, including 2 cases of Paprosky type IIIA and 8 cases of Paprosky type IIIB. There were 5 males and 5 females, mean age 73.6±8.1 yrs (range, 62-87 yrs), 5 left and 5 right cases. The preoperative thin-layer CT scan was preformed to reverse reconstruct digital pelvis. Five cases of one-piece flanged cups and 5 cases of decomposed flanged cups, including 3 cases of composite one-piece cups were designed by computer. The surgery was performed strictly according to the plan.Postoperative follow-up was performed to evaluate the Harris score. Operation time,intraoperative bleeding and other complications such as vascular and nerve injury, postoperative infection, and dislocation were counted. Pelvic X-ray was used to assess the height and horizontal position of the center of rotation and the stability of the prosthesis.Results:The surgical procedure was successful, with an average operative time of 147.9±48.3 min (range, 96-212 min) and an average intraoperative bleeding of 730.4±262.6 ml (range, 500-1 300 ml). The mean time of final follow-up was 40.8±18.7 months (range, 16-70 months) after surgery. At the last follow-up, the average Harris score was 83.80±6.73, with 4 cases excellent, 5 cases good, and 1 case fair. The excellent and good rate was 90%. The last Harris score was significantly higher than that before operation 28.60±8.40 ( t=16.84, P<0.001). The height of affected hip joint rotation center decreased from 46.24±7.74 mm before operation to 15.54±2.54 mm after operation with significant difference ( t=14.61, P<0.001). It was slightly higher than the opposite side (13.81±1.48 mm), which had no significant difference ( t=1.83, P=0.100). The horizontal distance of affected hip joint rotation center increased from 33.79±5.27 mm before operation to 40.53±4.50 mm after operation with significant difference ( t=3.62, P=0.006). It had no significant difference ( t=1.28, P=0.232) compared with the opposite side (38.54±3.46 mm). All incisions were healed in one stage without infection, vascular or nerve injury. During the following-up, all prostheses were in satisfied position without loosening, dislocation or screw breaks. Conclusion:Digitally assisted 3D-printed flanged cups can be used in hip revision with severe acetabular bone defect. It can not only improve hip joint function, but also restore the acetabular rotation center and the prosthesis stability, which can achieve good early and mid-term effect.
RESUMO
Objective:To analyze the efficacy of the reconstruction of the proximal humerus by reverse shoulder arthroplasty with three-dimensional (3D) printing technology after tumor rescetion.Methods:A retrospective analysis was conducted on the data of eight patients undergoing semi-constrained reverse shoulder arthroplasty with 3D printing technology after the resection of bone tumors in proximal humeri at the Affiliated Wuxi People's Hospital of Nanjing Medical University from December 2017 to January 2021. There were four males and four females with an average age of 55.1 (range, 31-73) years, all of whom had unilateral onset, 2 on the left and 6 on the right. There was one case of leiomyosarcoma (Enneking IIB), two cases of chondrosarcomas (one Enneking IA and one Enneking IB), four cases of Campanacci grade 3 giant cell tumor of bone, and one case of bone metastasis of lung adenocarcinoma. Individualized prosthesis and implantation protocol were completed preoperatively in all patients. The glenoid baseplate was manufactured using 3D printing technology. During the surgery, Malawer type I tumor resection and semi-constrained reverse shoulder arthroplasty were performed, with 6 cases simultaneously using allograft-prosthetic composite reconstruction. The follow-up was scheduled, and the patient received X-ray examination of the shoulder. The range of motion of the shoulder was measured, the Constant-Murley score and musculoskeletal tumor society (MSTS) score were recorded.Results:All 8 patients successfully completed the surgery, with a surgical time of 173.8±46.7 min (range, 130-260 min), intraoperative blood loss of 487.5±334.6 ml (range 200-1,200 ml), and proximal humeral resection of 9.9±4.6 cm (range, 4.5-19.0 cm). All patients were followed up for a period of 45.6±12.5 months (range, 24-60 months). At the last follow-up, the abduction ranges of motion of the affected shoulders increased from 27.5°±14.4° pre-operatively to 106.3°±21.8° post-operatively, with a statistically significant difference ( t=11.37, P<0.001). The forward flexion ranges increased from 28.1°±12.8° pre-operatively to 115.6°±24.0° post-operatively, with a statistically significant difference ( t=11.49, P<0.001). The Constant-Murley score was improved from 40.5±14.3 pre-operatively to 79.3±11.2 post-operatively, with a statistically significant difference ( t=9.58, P<0.001). The MSTS score was 25.6±2.2 (range, 23-28), including 6 excellent cases and 2 good cases. At 2 weeks after surgery, one patient experienced joint dislocation that was successfully reduced manually. Up to the final follow-up, all patients had survived without local tumor recurrence, metastasis, prosthesis infection and loosening. Conclusion:3D printing technology assisted shoulder arthroplasty is helpful for effective reconstruction and shoulder joint function recovery after resection of proximal humeral tumors, with satisfactory outcomes in the early and middle stages.
RESUMO
Objective:To investigate the advantages and disadvantages of percutaneous compression plate (PCCP) for femoral neck fractures in the elderly patients.Methods:A retrospective study was conducted of the 31 elderly patients with femoral neck fracture who had been treated with PCCP from January 2012 to December 2018 at Orthopaedic Department, The First People's Hospital of Yancheng, Orthopaedic Department, The Ninth People's Hospital of Wuxi and Department of Orthopaedics, The People's Hospital of Wuxi. They were 16 men and 15 women, aged from 65 to 80 years (average, 70.5 years). By the Garden classification, 7 cases were type Ⅱ, 15 cases type Ⅲ and 9 cases type Ⅳ; by the Singh index, 4 cases were level Ⅲ, 11 cases level Ⅳ, 10 cases level Ⅴ and 6 cases level Ⅵ. The time from injury to operation ranged from 3 to 14 days (average, 5.8 days). The operation time, intraoperative blood loss, fracture reduction, fracture union time, complications and functional recovery of the hip were observed.Results:The operation time averaged 73.4 min and intraoperative blood loss 116.4 mL. At one week after operation, the Garden alignment index was level Ⅰ in 25 cases and level Ⅱ in 6. Superficial incision infection was noted in one case intraoperatively. Follow-ups for the 31 patients ranged from 12 to 47 months (mean, 18.9 months). All the fractures united after 4.9 months on average (from 4 to 8 months). Delayed union occurred in 2 cases, neck shortening in 12 cases, and avascular necrosis of femoral head in 3 displaced subcranial fractures 2 of which were high shear ones. The necrosis of femoral head was treated by arthroplasty in 2 and by conservative treatment in one. The Harris hip scores at the last follow-up for the 31 patients averaged 90.9 (from 75 to 100), giving 15 excellent, 12 good and 4 fair cases and an excellent to good rate of 87.1% (27/31).Conclusions:In treatment of femoral neck fractures in the elderly patients, PCCP has advantages of allowing early weight-bearing after operation, a high rate of fracture union, limited complications and quick and fine functional recovery of the hip. However, it should be used with caution in patients with severe osteoporosis, displaced subcranial or high shear fracture.
RESUMO
Objective:To explore the application of a 3D printed patient-specific guider (3D-PSG) in complex total knee arthroplasty (TKA).Methods:A retrospective analysis was performed of the data of 44 patients who had received complex artificial TKA for articular and extra-articular deformities of the knee from January 2016 to October 2019 at Department of Orthopaedic Surgery, Nanjing First Hospital. According to whether a 3D-PSG had been applied, the patients were divided into 2 groups. In the 3D-PSG group of 23 patients, there were 11 males and 12 females, with an age of 63.7 years ± 10.2 years (from 53 to 81 years); in the conventional group of 21 cases, there were 10 males and 11 females, with an age of 64.2 years ±12.1 years (from 51 to 79 years). In the 3D-PSG group, the preoperative CT data were 3D reconstructed for measurement of a full lower limb and design of a 3D-PSG and TKA was assisted by a 3D-PSG which had been manufactured by a 3D printer using the STL files of the 3D-PSG imported. In the conventional group TKA was performed in a standard manner. In the 3D-PSG group, the TKA surgical parameters in the preoperative plan were compared with actual surgical measurements. The 2 groups were compared in terms of operation time, intraoperative blood loss, postoperative drainage volume, length of hospital stay, visual analogue scale (VAS), Knee Society Score (KSS), hip knee ankle (HKA), frontal femoral component (FFC), frontal tibial component (FTC), lateral femoral flexion (LFF) and lateral tibial component (LTC).Results:There were no significant differences between the 2 groups in the preoperative general data, showing comparability ( P>0.05). In the 3D-PSG group, no significant differences were found between preoperative parameters designed and actual intraoperative measurements in the prosthetic type of femoral condyle (3.4±1.1 versus 3.5±0.9) or of tibial plateau (3.1±0.9 versus 3.3±1.2), or in the filler thickness (10.6 mm ± 3.2 mm versus 10.9 mm ± 4.7 mm) ( P>0.05). The 44 patients were followed up for an average of 10.8 months (from 7 to 13 months). The 3D-PSG group had significantly less operation time (65.7 min ± 10.5 min), intraoperative blood loss (19.8 mL ±7.3 mL), postoperative drainage volume (124.6 mL ± 27.9 mL) and hospital stay (7.3 d ± 2.5 d) than the conventional group (82.4 min ± 11.7 min, 86.5 mL ± 35.7 mL, 154.6 mL ± 21.3 mL and 10.6 d ± 3.1 d) ( P<0.05). The VAS and KSS scores at postoperative day 1, week 1 and week 2 in the 3D-PSG group were significantly better than those in the conventional group ( P<0.05). Significantly more patients in the 3D-PSG group achieved approximately ideal values in HKA, FFC, FTC, LFF and LTC than those in the conventional group ( P<0.05). Conclusion:A 3D printed patient-specific guider may improve surgical accuracy, reduce operation time and achieve better surgical outcomes in complex total knee arthroplasty.
RESUMO
Objective To compare the effects of bone transport versus induced membrane technique for large segmental tibial defects.Methods The clinical data were analyzed retrospectively of 89 patients with large segmental tibial defect who had been treated at Department of Orthopaedics,Wuxi No.9 People's Hospital from June 2005 to February 2017 using bone transport or induced membrane technique.They were 58males and 31 females,aged from 13 to 74 years (average,38.0 years).The bone transport group had 59cases and the induced membrane technique group 30 cases.The 2 groups were compared in terms of preoperative general data and postoperative bone nonunion,bone healing time,complications and functional recovery of the adjacent joint.Results There were no statistically significant differences between the 2groups in terms of age,gender,cause or type of defects,associated injury,course of disease,functionary scores of the adjacent joint or number of operations,showing compatibility between the 2 groups (P > 0.05).All the patients were followed up for 12 to 48 months (average,20 months).The bone transport group had significandy longer clinical healing time (14.7 ± 5.4 months) and significantly higher incidences of major complications (50.8%),minor complications (57.6%) and overall complications (83.1%) than the induced membrane technique group (11.2 ± 2.8 months,16.7%,26.7% and 30.0%,respectively) (P < O.05),but significantly lower functionary scores of the adjacent joint (86.4 ± 5.0 points) than the induced membrane technique group (88.8 ± 4.9 points) (P < 0.05).Conclusions Both bone transport and induced membrane technique are effective repairs for large segmental tibial defects.However,induced membrane technique may be superior to bone transport in terms of bone healing,complications and functional recovery.
RESUMO
Ameloblastoma in the tibia is rare. Limb reconstruction after tumor resection is challenging in terms of selection of the operative method. Here, we report a case of radical resection of an ameloblastoma in the mid-distal tibia combined with limb salvage using a three-dimensional (3D)-printed prosthesis replacement, with 1-year follow-up results. After receiving local institutional review board approval, a titanium alloy prosthesis was designed using a computer and manufactured with 3D-printing technology. During the operation, the stem of the prosthesis was inserted closely into the proximal tibial medullary cavity. Then, the metal ankle mortise and the talus were compacted closely. Radiographic results at 1-year follow up showed that the prosthesis was well placed, and no loosening was observed. The Musculoskeletal Tumor Society (MSTS) 93 functional score was 26 points, and the functional recovery percentage was 86.7%. Computer-assisted 3D-printing technology allowed for more volume and structural compatibility of the prosthesis, thereby ensuring a smooth operation and initial prosthetic stabilization. During the follow up, the presence of bone ingrowths on the porous surface of some segments of the prosthesis suggested good outcomes for long-term biological integration between the prosthesis and host bone.
Assuntos
Ligas , Ameloblastoma , Tornozelo , Comitês de Ética em Pesquisa , Extremidades , Seguimentos , Salvamento de Membro , Métodos , Próteses e Implantes , Tálus , Tíbia , TitânioRESUMO
Objective To observe the effect ofJianpi-Huoxue decoction on the adrenocorticotropic hormone levels and vascular endothelial growth factor of patients with chronic nephritis.Methods 120 patients with chronic nephritis from January 2012 to December 2013 in TCM Hospital of Yanggu county were selected and recruited into a control group and a treatment group, with 40 patients in each group, according to random number table method. The control group was given oral indomethacin, 1 tablets each time, 3 times/d; intramuscular injection of methotrexate, 1 piece/time, 1 times/week. The treatment group was additionally treated by Jianpi-Huoxue decoction on the basis of the control group. Both groups were treated for 3 months. The serum adrenocorticotropic hormone and vascular endothelial growth factor levels were measured before and after the treatment,and efficacy and safety were also evaluated.Results After the treatment, the total effective rate was 72.5% (29/40) in the control group and 97.5% (39/40) in the treatment group, with significant differences (χ2=7.941,P<0.05). The ACTH levels after treatment was (13.82 ± 5.94 ng/Lvs. 8.01 ± 4.16 ng/L) in the treatment group and (18.73 ± 6.84 ng/Lvs. 8.07 ± 4.08 ng/L) in the control group, showing significant increase compared with before treatment (P<0.01). The level of VEGF was (61.92 ± 26.37 ng/Lvs. 83.72 ± 30.63 ng/L) in the treatment group and (49.36 ± 23.93 ng/Lvs.84.34 ± 33.49 ng/L) in the control group, showing significant decrease than before treatment (P<0.01). After the treatment, the increase of ACTH and the decrease of VEGF in the treatment group were better than those in the control group (t=3.427, 2.231,P<0.05).ConclusionsJianpi-Huoxue decoction combined with conventional western therapy can increase the level of ACTH in patients with nephritis, reduce VEGF, and improve clinical curative effects.