Gelatin and Tannic Acid Based Iongels for Muscle Activity Recording and Stimulation Electrodes.

Iongels are soft ionic conducting materials, usually composed of polymer networks swollen with ionic liquids (ILs), which are being investigated for applications ranging from energy to bioelectronics. The employment of iongels in bioelectronic devices such as bioelectrodes or body sensors has been limited by the lack of biocompatibility of the ILs and/or polymer matrices. In this work, we present iongels prepared from solely biocompatible materials: (i) a biobased polymer network containing tannic acid as a cross-linker in a gelatin matrix and (ii) three different biocompatible cholinium carboxylate ionic liquids. The resulting iongels are flexible and elastic with Young's modulus between 11.3 and 28.9 kPa. The morphology of the iongels is based on a dual polymer network system formed by both chemical bonding due to the reaction of the gelatin's amines with the polyphenol units and physical interactions between the tannic acid and the gelatin. These biocompatible iongels presented high ionic conductivity values, from 0.003 and up to 0.015 S·cm-1 at room temperature. Furthermore, they showed excellent performance as a conducting gel in electrodes for electromyography and electrocardiogram recording as well as muscle stimulation.

Ionic Hydrogel for Accelerated Dopamine Delivery via Retrodialysis.

Local drug delivery directly to the source of a given pathology using retrodialysis is a promising approach to treating otherwise untreatable diseases. As the primary material component in retrodialysis, the semipermeable membrane represents a critical point for innovation. This work presents a new ionic hydrogel based on polyethylene glycol and acrylate with dopamine counterions. The ionic hydrogel membrane is shown to be a promising material for controlled diffusive delivery of dopamine. The ionic nature of the membrane accelerates uptake of cationic species compared to a nonionic membrane of otherwise similar composition. It is demonstrated that the increased uptake of cations can be exploited to confer an accelerated transport of cationic species between reservoirs as is desired in retrodialysis applications. This effect is shown to enable nearly 10-fold increases in drug delivery rates from low concentration solutions. The processability of the membrane is found to allow for integration with microfabricated devices which will in turn accelerate adaptation into both existing and emerging device modalities. It is anticipated that a similar materials design approach may be broadly applied to a variety of cationic and anionic compounds for drug delivery applications ranging from neurological disorders to cancer.

Electrophoretic drug delivery for seizure control.

The persistence of intractable neurological disorders necessitates novel therapeutic solutions. We demonstrate the utility of direct in situ electrophoretic drug delivery to treat neurological disorders. We present a neural probe incorporating a microfluidic ion pump (µFIP) for on-demand drug delivery and electrodes for recording local neural activity. The µFIP works by electrophoretically pumping ions across an ion exchange membrane and thereby delivers only the drug of interest and not the solvent. This "dry" delivery enables precise drug release into the brain region with negligible local pressure increase. The therapeutic potential of the µFIP probe is tested in a rodent model of epilepsy. The µFIP probe can detect pathological activity and then intervene to stop seizures by delivering inhibitory neurotransmitters directly to the seizure source. We anticipate that further tailored engineering of the µFIP platform will enable additional applications in neural interfacing and the treatment of neurological disorders.

Conducting Polymer Scaffolds Based on Poly(3,4-ethylenedioxythiophene) and Xanthan Gum for Live-Cell Monitoring.

Conducting polymer scaffolds can promote cell growth by electrical stimulation, which is advantageous for some specific type of cells such as neurons, muscle, or cardiac cells. As an additional feature, the measure of their impedance has been demonstrated as a tool to monitor cell growth within the scaffold. In this work, we present innovative conducting polymer porous scaffolds based on poly(3,4-ethylenedioxythiophene) (PEDOT):xanthan gum instead of the well-known PEDOT:polystyrene sulfonate scaffolds. These novel scaffolds combine the conductivity of PEDOT and the mechanical support and biocompatibility provided by a polysaccharide, xanthan gum. For this purpose, first, the oxidative chemical polymerization of 3,4-ethylenedioxythiophene was carried out in the presence of polysaccharides leading to stable PEDOT:xanthan gum aqueous dispersions. Then, by a simple freeze-drying process, porous scaffolds were prepared from these dispersions. Our results indicated that the porosity of the scaffolds and mechanical properties are tuned by the solid content and formulation of the initial PEDOT:polysaccharide dispersion. Scaffolds showed interconnected pore structure with tunable sizes ranging between 10 and 150 µm and Young's moduli between 10 and 45 kPa. These scaffolds successfully support three-dimensional cell cultures of MDCK II eGFP and MDCK II LifeAct epithelial cells, achieving good cell attachment with very high degree of pore coverage. Interestingly, by measuring the impedance of the synthesized PEDOT scaffolds, the growth of the cells could be monitored.

Biodegradable Polycarbonate Iongels for Electrophysiology Measurements.

In recent years, gels based on ionic liquids incorporated into polymer matrices, namely iongels, have emerged as long-term contact media for cutaneous electrophysiology. Iongels possess high ionic conductivity and negligible vapor pressure and can be designed on demand. In spite of the extensive efforts devoted to the preparation of biodegradable ionic liquids, the investigations related to the preparation of iongels based on biodegradable polymers remain scarce. In this work, biodegradable polycarbonate-based iongels are prepared by ring-opening polymerization of N-substituted eight ring membered cyclic carbonate monomers in the presence of imidazolium lactate ionic liquid. Our iongels are able to take up 10⁻30 wt % of ionic liquid and become softer materials by increasing the amount of free ionic liquid. Rheological measurements showed that the cross-over point between the storage modulus G' and loss modulus G″ occurs at lower angular frequencies when the loading of free ionic liquid increases. These gels are able to take up to 30 wt % of the ionic liquid and the ionic conductivity of these gels increased up to 5 × 10-4 S·cm-1 at 25 °C as the amount of free ionic liquid increased. Additionally, we assess the biodegradation studies of the iongels by immersing them in water. The iongels decrease the impedance with the human skin to levels that are similar to commercial Ag/AgCl electrodes, allowing an accurate physiologic signals recording. The low toxicity and biodegradability of polycarbonate-based iongels make these materials highly attractive for cutaneous electrophysiology applications.

Low-Temperature Cross-Linking of PEDOT:PSS Films Using Divinylsulfone.

Recent interest in bioelectronics has prompted the exploration of properties of conducting polymer films at the interface with biological milieus. Poly(3,4-ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT:PSS) from a commercially available source has been used as a model system for these studies. Different cross-linking schemes have been used to stabilize films of this material against delamination and redispersion, but the cost is a decrease in the electrical conductivity and/or additional heat treatment. Here we introduce divinylsulfone (DVS) as a new cross-linker for PEDOT:PSS. Thanks to the higher reactiveness of the vinyl groups of DVS, the cross-linking can be performed at room temperature. In addition, DVS does not reduce electronic conductivity of PEDOT:PSS but rather increases it by acting as a secondary dopant. Cell culture studies show that PEDOT:PSS:DVS films are cytocompatible and support neuroregeneration. As an example, we showed that this material improved the transconductance value and stability of an organic electrochemical transistor (OECT) device. These results open the way for the utilization of DVS as an effective cross-linker for PEDOT:PSS in bioelectronics applications.

Conducting Polymer Iongels Based on PEDOT and Guar Gum.

Conducting polymer hydrogels are attracting much interest in biomedical and energy-storage devices due to their unique electrochemical properties including their ability to conduct both electrons and ions. They suffer, however, from poor stability due to water evaporation, which causes the loss of mechanical and ion conduction properties. Here we show for the first time a conducting polymer gel where the continuous phase is a nonvolatile ionic liquid. The novel conducting iongel is formed by a natural polysaccharide (guar gum), a conductive polymer poly(3,4-ethylenedioxythiophene) (PEDOT), and an ionic liquid (IL) 1-butyl-3-methylimidazolium chloride (BMIMCl). First, an aqueous dispersion of PEDOT:guar gum is synthesized by an oxidative polymerization process of EDOT in the presence of the polysaccharide as stabilizer. The resulting PEDOT:guar gum was isolated as a powder by removing the water via freeze-drying process. In the final step, conducting iongels were prepared by the PEDOT:guar gum mixed with the ionic liquid by a heating-cooling process. The rheological properties show that the material exhibits gel type behavior between 20 and 80 °C. Interestingly, the conducting polymer iongel presents redox properties as well as high ionic conductivities (10-2 S cm-1). This material presents a unique combination of properties by mixing the electronic conductivity of PEDOT, the ionic conductivity and negligible vapor pressure of the ionic liquid and the support and flexibility given by guar gum.

Poly(3,4-ethylenedioxythiophene) (PEDOT) Derivatives: Innovative Conductive Polymers for Bioelectronics.

Poly(3,4-ethylenedioxythiophene)s are the conducting polymers (CP) with the biggest prospects in the field of bioelectronics due to their combination of characteristics (conductivity, stability, transparency and biocompatibility). The gold standard material is the commercially available poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). However, in order to well connect the two fields of biology and electronics, PEDOT:PSS presents some limitations associated with its low (bio)functionality. In this review, we provide an insight into the synthesis and applications of innovative poly(ethylenedioxythiophene)-type materials for bioelectronics. First, we present a detailed analysis of the different synthetic routes to (bio)functional dioxythiophene monomer/polymer derivatives. Second, we focus on the preparation of PEDOT dispersions using different biopolymers and biomolecules as dopants and stabilizers. To finish, we review the applications of innovative PEDOT-type materials such as biocompatible conducting polymer layers, conducting hydrogels, biosensors, selective detachment of cells, scaffolds for tissue engineering, electrodes for electrophysiology, implantable electrodes, stimulation of neuronal cells or pan-bio electronics.

Poly(3,4-ethylenedioxythiophene):GlycosAminoGlycan Aqueous Dispersions: Toward Electrically Conductive Bioactive Materials for Neural Interfaces.

UNLABELLED: There is an actual need of advanced materials for the emerging field of bioelectronics. One commonly used material is the conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) ( PEDOT: PSS) due to its general use in organic electronics. However, depending on the application in bioelectronics, PEDOT: PSS is not fully biocompatible due to the high acidity of the residual sulfonate protons of PSS. In this paper, the synthesis and biocompatibility properties of new poly(3,4-ethylenedioxythiophene):GlycosAminoGlycan ( PEDOT: GAG) aqueous dispersions and its resulting films are shown. Thus, negatively charged GAGs as an alternative to PSS are presented. Three different commercially available GAGs, hyaluronic acid, heparin, and chondroitin sulfate are used. Indeed, PEDOT: GAGs dispersions are prepared through an oxidative chemical polymerization in water. Biocompatibility assays of the PEDOT: GAGs coatings are performed using SH-SY5Y and CCF-STTG1 cell lines and with ATP and Ca(2+) . Results show full biocompatibility and a pronounced anti-inflammatory effect. This last characteristic becomes crucial if implanted in the body. These materials can be used for in vivo applications, as transistor or electrode for electrical recording and for all the possible situations when there is contact between electronic circuits and living tissues.

Comparison of semi-batch vs. continuously fed anaerobic bioreactors for the treatment of a high-strength, solids-rich pumpkin-processing wastewater.

The objective of this work was to compare two different high-rate anaerobic bioreactor configurations--the anaerobic sequencing batch reactor (ASBR) and the upflow anaerobic solid removal (UASR) reactor--for the treatment of a solid-rich organic wastewater with a high strength. The two, 4.5-L reactors were operated in parallel for close to 100 days under mesophilic conditions (37°C) with non-granular biomass by feeding a pumpkin wastewater with ∼4% solids. The organic loading rate of pumpkin wastewater was increased periodically to a maximum of 8 g COD L(-1) d(-1) by shortening the hydraulic retention time to 5.3 days. Compositional analysis of pumpkin wastewater revealed deficiencies in the trace metal cobalt and alkalinity. With supplementation, the ASBR outperformed the UASR reactor with total chemical oxygen demand (COD) removal efficiencies of 64% and 53%, respectively, achieving a methane yield of 0.27 and 0.20 L CH4 g(-1) COD fed to the ASBR and UASR, respectively. The better performance realized with the ASBR and this specific wastewater was attributed to its semi-batch, dynamic operating conditions rather than the continuous operating conditions of the UASR reactor.