A Fully Integrated, Power-Efficient, 0.07-2.08 mA, High-Voltage Neural Stimulator in a Standard CMOS Process.

This paper presents a fully integrated high-voltage (HV) neural stimulator with on-chip HV generation. It consists of a neural stimulator front-end that delivers stimulation currents up to 2.08 mA with 5 bits resolution and a switched-capacitor DC-DC converter that generates a programmable voltage supply from 4.2 V to 13.2 V with 4 bits resolution. The solution was designed and fabricated in a standard 180 nm 1.8 V/3.3 V CMOS process and occupied an active area of 2.34 mm2. Circuit-level and block-level techniques, such as a proposed high-compliance voltage cell, have been used for implementing HV circuits in a low-voltage CMOS process. Experimental validation with an electrical model of the electrode−tissue interface showed that (1) the neural stimulator can handle voltage supplies up to 4 times higher than the technology's nominal supply, (2) residual charge­without passive discharging phase­was below 0.12% for the whole range of stimulation currents, (3) a stimulation current of 2 mA can be delivered with a voltage drop of 0.9 V, and (4) an overall power efficiency of 48% was obtained at maximum stimulation current.

A 32-Channel Time-Multiplexed Artifact-Aware Neural Recording System.

This paper presents a low-power, low-noise microsystem for the recording of neural local field potentials or intracranial electroencephalographic signals. It features 32 time-multiplexed channels at the electrode interface and offers the possibility to spatially delta encode data to take advantage of the large correlation of signals captured from nearby channels. The circuit also implements a mixed-signal voltage-triggered auto-ranging algorithm which allows to attenuate large interferers in digital domain while preserving neural information. This effectively increases the system dynamic range and avoids the onset of saturation. A prototype, fabricated in a standard 180 nm CMOS process, has been experimentally verified in-vitro with cellular cultures of primary cortical neurons from mice. The system shows an integrated input-referred noise in the 0.5-200 Hz band of 1.4 µVrms for a spot noise of about 85 nV /√{Hz}. The system draws 1.5 µW per channel from 1.2 V supply and obtains 71 dB + 26 dB dynamic range when the artifact-aware auto-ranging mechanism is enabled, without penalising other critical specifications such as crosstalk between channels or common-mode and power supply rejection ratios.

Recording Strategies for High Channel Count, Densely Spaced Microelectrode Arrays.

Neuroscience research into how complex brain functions are implemented at an extra-cellular level requires in vivo neural recording interfaces, including microelectrodes and read-out circuitry, with increased observability and spatial resolution. The trend in neural recording interfaces toward employing high-channel-count probes or 2D microelectrodes arrays with densely spaced recording sites for recording large neuronal populations makes it harder to save on resources. The low-noise, low-power requirement specifications of the analog front-end usually requires large silicon occupation, making the problem even more challenging. One common approach to alleviating this consumption area burden relies on time-division multiplexing techniques in which read-out electronics are shared, either partially or totally, between channels while preserving the spatial and temporal resolution of the recordings. In this approach, shared elements have to operate over a shorter time slot per channel and active area is thus traded off against larger operating frequencies and signal bandwidths. As a result, power consumption is only mildly affected, although other performance metrics such as in-band noise or crosstalk may be degraded, particularly if the whole read-out circuit is multiplexed at the analog front-end input. In this article, we review the different implementation alternatives reported for time-division multiplexing neural recording systems, analyze their advantages and drawbacks, and suggest strategies for improving performance.

Charge-Redistribution Based Quadratic Operators for Neural Feature Extraction.

This paper presents a SAR converter based mixed-signal multiplier for the feature extraction of neural signals using quadratic operators. After a thorough analysis of design principles and circuit-level aspects, the proposed architecture is explored for the implementation of two quadratic operators often used for the characterization of neural activity, the moving average energy (MAE) operator and the nonlinear energy operator (NEO). Programmable chips for both operators have been implemented in a HV-180 nm CMOS process. Experimental results confirm their suitability for energy computation and action potential detection and the accomplished area×power performance is compared to prior art. The MAE and NEO prototypes, at a sampling rate of 30kS/s, consume 116 nW and 178 nW, respectively, and digitize both the input neural signal and the operator outcome, with no need for digital multipliers.

Phase Synchronization Operator for On-Chip Brain Functional Connectivity Computation.

This paper presents an integer-based digital processor for the calculation of phase synchronization between two neural signals. It is based on the measurement of time periods between two consecutive minima. The simplicity of the approach allows for the use of elementary digital blocks, such as registers, counters, and adders. The processor, fabricated in a 0.18- µm CMOS process, only occupies 0.05 mm 2 and consumes 15 nW from a 0.5 V supply voltage at a signal input rate of 1024 S/s. These low-area and low-power features make the proposed processor a valuable computing element in closed-loop neural prosthesis for the treatment of neural disorders, such as epilepsy, or for assessing the patterns of correlated activity in neural assemblies through the evaluation of functional connectivity maps.

System-Level Design of a 64-Channel Low Power Neural Spike Recording Sensor.

This paper reports an integrated 64-channel neural spike recording sensor, together with all the circuitry to process and configure the channels, process the neural data, transmit via a wireless link the information and receive the required instructions. Neural signals are acquired, filtered, digitized and compressed in the channels. Additionally, each channel implements an auto-calibration algorithm which individually configures the transfer characteristics of the recording site. The system has two transmission modes; in one case the information captured by the channels is sent as uncompressed raw data; in the other, feature vectors extracted from the detected neural spikes are released. Data streams coming from the channels are serialized by the embedded digital processor. Experimental results, including in vivo measurements, show that the power consumption of the complete system is lower than 330 µW.

A Low Noise Amplifier for Neural Spike Recording Interfaces.

This paper presents a Low Noise Amplifier (LNA) for neural spike recording applications. The proposed topology, based on a capacitive feedback network using a two-stage OTA, efficiently solves the triple trade-off between power, area and noise. Additionally, this work introduces a novel transistor-level synthesis methodology for LNAs tailored for the minimization of their noise efficiency factor under area and noise constraints. The proposed LNA has been implemented in a 130 nm CMOS technology and occupies 0.053 mm-sq. Experimental results show that the LNA offers a noise efficiency factor of 2.16 and an input referred noise of 3.8 µVrms for 1.2 V power supply. It provides a gain of 46 dB over a nominal bandwidth of 192 Hz-7.4 kHz and consumes 1.92 µW. The performance of the proposed LNA has been validated through in vivo experiments with animal models.

A 515 nW, 0-18 dB Programmable Gain Analog-to-Digital Converter for In-Channel Neural Recording Interfaces.

This paper presents a low-area low-power Switched-Capacitor (SC)-based Programmable-Gain Analog-to-Digital Converter (PG-ADC) suitable for in-channel neural recording applications. The PG-ADC uses a novel implementation of the binary search algorithm that is complemented with adaptive biasing techniques for power saving. It has been fabricated in a standard CMOS 130 nm technology and only occupies 0.0326 mm(2). The PG-ADC has been optimized to operate under two different sampling modes, 27 kS/s and 90 kS/s. The former is tailored for raw data conversion of neural activity, whereas the latter is used for the on-the-fly feature extraction of neural spikes. Experimental results show that, under a voltage supply of 1.2 V, the PG-ADC obtains an ENOB of 7.56 bit (8-bit output) for both sampling modes, regardless of the gain setting. The amplification gain can be programmed from 0 to 18 dB. The power consumption of the PG-ADC at 90 kS/s is 1.52 µW with a FoM of 89.49 fJ/conv, whereas at 27 kS/s it consumes 515 nW and obtains a FoM of 98.31 fJ/conv .

A low-power programmable neural spike detection channel with embedded calibration and data compression.

This paper reports a programmable 400 µm pitch neural spike recording channel, fabricated in a 130 nm standard CMOS technology, which implements amplification, filtering, digitization, analog spike detection plus feature extraction, and self-calibration functionalities. It can operate in two different output modes: 1) signal tracking, in which the neural signal is sampled and transmitted as raw data; and 2) feature extraction, in which the spikes of the neural signal are detected and encoded by piece-wise linear curves. Additionally, the channel offers a foreground calibration procedure in which the amplification gain and the passband of the embedded filter can be self-adjusted. The amplification stage obtains a noise efficiency factor of 2.16 and an input referred noise of 2.84 µVrms over a nominal bandwidth of 167 Hz-6.9 kHz. The channel includes a reconfigurable 8-bit analog-to-digital converter combined with a 3-bit controlled programmable gain amplifier for adjusting the input signal to the full scale range of the converter. This combined block achieves an overall energy consumption per conversion of 102 fJ at 90 kS/s. The energy consumed by the circuit elements which are strictly related to the digitization process is 14.12 fJ at the same conversion rate. The complete channel consumes 2.8 µW at 1.2 V voltage supply when operated in the signal tracking mode, and 3.1 µW when the feature extraction mode is enabled.