X-ray Micro-Computed Tomography: A Powerful Device to Analyze the 3D Microstructure of Anode-Electrolyte in BaZr0.8Y0.2O3 Protonic Ceramic Electrochemical Cells and the Reduction Behavior.

New advanced fuel cell technologies are moving towards high-temperature proton conductors (HTPCs) to meet environmental issues. Their elaboration remains a challenge and micro-computed tomography (µCT) is an innovative way to control their quality. NiO-BZY anodic supports of a protonic ceramic electrochemical cell (PCEC), elaborated by co-tape casting and co-sintered at 1350 °C, were coated with a BZY20 electrolyte layer by DC magnetron sputtering. The µCT allowed to observe defects inside the volume of these PCEC half-cells and to show their evolution after an annealing treatment at 1000 °C and reduction under hydrogen. This technique consists in obtaining a 3D reconstruction of all the cross-sectional images of the whole sample, slice by slice. This allows seeing inside the sample at any desired depth. The resolution of 0.35 µm is perfectly adapted to this type of problem considering the thickness of the different layers of the sample and the size of the defects. Defects were detected, and their interpretation was possible thanks to the 3D view, such as the phenomenon of NiO grain enlargement explaining defects in the electrolyte, the effect of NiO reduction, and finally, some anomalies due to the shaping process. Ways to anticipate these defects were then proposed.

Innovative Magnetic Nanoparticles for PET/MRI Bimodal Imaging.

Superparamagnetic iron oxide nanoparticles were developed as positron emission tomography (PET) and magnetic resonance imaging (MRI) bimodal imaging agents. These nanoparticles (NPs), with a specific nanoflower morphology, were first synthesized and simultaneously functionalized with 3,4-dihydroxy-l-phenylalanine (LDOPA) under continuous hydrothermal conditions. The resulting NPs exhibited a low hydrodynamic size of 90 ± 2 nm. The functional groups of LDOPA (-NH2 and -COOH) were successfully used for the grafting of molecules of interest in a second step. The nanostructures were modified by poly(ethylene glycol) (PEG) and a new macrocyclic chelator MANOTA for further 64Cu radiolabeling for PET imaging. The functionalized NPs showed promising bimodal (PET and MRI) imaging capability with high r 2 and r 2* (T 2 and T 2* relaxivities) values and good stability. They were mainly uptaken from liver and kidneys. No cytotoxicity effect was observed. These NPs appear as a good candidate for bimodal tracers in PET/MRI.

Contact laws between nanoparticles: the elasticity of a nanopowder.

Studies of the mechanical contact between nanometer-scale particles provide fundamental insights into the mechanical properties of materials and the validity of contact laws at the nanoscale which are still under debate for contact surfaces approaching atomic dimensions. Using in situ Brillouin light scattering under high pressure, we show that effective medium theories successfully predict the macroscopic sound velocities in nanopowders if one takes into account the cementation of the contacts Our measurements suggest the relevance of the continuum approach and effective medium theories to describe the contact between nanoparticles of diameters as small as 4 nm, i.e. with radii of contact of a few angstroms. In particular, we demonstrate that the mechanical properties of nanopowders strongly depend on the surface state of the nanoparticles. The presence of molecular adsorbates modifies significantly the contact laws.

Efficient functionalization of magnetite nanoparticles with phosphonate using a one-step continuous hydrothermal process.

For the first time, phosphonate-functionalized magnetite nanoparticles (Fe3O4 NPs) were synthesized using a one-step continuous hydrothermal process. The NP surface was modified using a hydrophilic organic molecule, namely 6-phosphonohexanoic acid (PHA). NPs were fully characterized (TEM, XRD, DLS, ζ-potential, TGA, FTIR, XPS and specific surface area measurements) in order to investigate PHA effect on size, oxidation state, anchoring and colloidal stability. PHA reduced the crystallite size and size distribution and improved greatly colloidal stability when compared with bare Fe3O4 NPs. Moreover, PHA was grafted on the NP surface according to three different conformations: as mononuclear monodendates, as binuclear bidentates or as lying-down complexes. This report is very promising regarding the stabilization and functionalization of Fe3O4 NPs by phosphonate molecules under continuous hydrothermal conditions. The post-grafting of polymers such as polyethylene glycol can be considered owing to the presence of free carboxyl groups (-COOH) on the surface of Fe3O4 NPs.

Thermodynamics of nanoparticles: experimental protocol based on a comprehensive Ginzburg-Landau interpretation.

The effects of surface and interface on the thermodynamics of small particles require a deeper understanding. This step is crucial for the development of models that can be used for decision-making support to design nanomaterials with original properties. On the basis of experimental results for phase transitions in compressed ZnO nanoparticles, we show the limitations of classical thermodynamics approaches (Gibbs and Landau). We develop a new model based on the Ginzburg-Landau theory that requires the consideration of several terms, such as the interaction between nanoparticles, pressure gradients, defect density, and so on. This phenomenological approach sheds light on the discrepancies in the literature as it identifies several possible parameters that should be taken into account to properly describe the transformations. For the sake of clarity and standardization, we propose an experimental protocol that must be followed during high-pressure investigations of nanoparticles in order to obtain coherent, reliable data that can be used by the scientific community.

One step continuous hydrothermal synthesis of very fine stabilized superparamagnetic nanoparticles of magnetite.

Stable suspensions of citrated SPIO nanoparticles were synthesised in one step using a hydrothermal continuous process. Citrates control the crystallite size and the oxidation degree of metallic ions despite the very short reaction time (4 s). Magnetite particles, Fe(2.94)O(4), with an average size of 4 nm and good monodispersity were obtained.

Tin-based mesoporous silica for the conversion of CO2 into dimethyl carbonate.

Sn-based SBA-15 was prepared by reacting di-n-butyldimethoxystannane with SBA-15 pretreated with trimethylchlorosilane (TMCS) to cap the external hydroxyl groups. Small-angle X-ray diffraction (SXRD), infrared spectroscopy (IR), nitrogen adsorption/desorption, transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and inductively coupled plasma atomic emission (ICP-AES) measurements allow us to propose that the organotin species are located within the pore channels of the mesoporous host. This novel material catalyzes selectively the coupling of CO(2) with methanol to dimethyl carbonate (DMC). The reaction time-conversion dependence shows that a turnover number (TON) of 16 can be reached at 423 K under 20 MPa, which is among the highest reported so far in the absence of water traps. Moreover, as the catalytic activity is retained after recycling, even higher values can be obtained on a cumulative basis. A further TON increase is observed with the reaction temperature. Interestingly, the tin-based SBA-15 mesoporous material exhibits lower TONs if the TMCS pretreatment is left out. Therefore, the organotin species located outside the channels are far less active than those located within.

Investigation of pyrite oxidation by hexavalent chromium: solution species and surface chemistry.

Pyrite oxidation processes by aqueous Cr(VI) were investigated at 25 degrees C under an argon atmosphere. Synthetic pyrite suspensions (6 g L(-1)) were reacted for 20 h with a range of Cr(VI) solutions from 0 to 700 microM and at pH 2-12. The main objective of this work was to investigate the reaction mechanisms by emphasizing the role of sulfur species. Aqueous chemical processes were well illustrated in acidic media where significant amounts of sulfate and iron species were determined. Sulfate anions are the final stable sulfur species involved in the reaction pathway. Experiments showing complete Cr(VI) removal from solution displayed ratios [S(VI)]/[Fe](tot)<2, probably due to a deficit in aqueous sulfur species. Experiments showing incomplete Cr(VI) removal displayed ratios [Cr(VI)](removed)/[S(VI)] close to 1.5. This ratio was found to be consistent with the formation of thiosulfate (S(2)O(2-)(3)). Thiosulfate ions disproportionated into elemental sulfur S(0) and tetrathionate ions (S(4)O(2-)(6)) that were finally oxidized to sulfate anions under acidic conditions. The distribution of the oxidation state of sulfur atoms at the pyrite surface determined by XPS was additional evidence for the multistep sulfur oxidation process. The presence of elemental sulfur in the S(2p) spectra correlated well with the disproportion of thiosulfate under acidic conditions.

Pyrite oxidation by hexavalent chromium: investigation of the chemical processes by monitoring of aqueous metal species.

Pyrite, an iron sulfide, occurs in many soils and sediments, making it an important natural reductant of toxic metal pollutants. This study investigated the processes leading to aqueous Cr(VI) reduction by pyrite in a closed thermostated (25 +/- 0.1 degrees C) system and under an argon atmosphere. Synthetic pyrite suspensions were reacted with a range of Cr(VI) solutions from 0 to 7 x 10(-4) M and at pH 2-8. Metal species concentrations were continuously monitored during a period lasting approximately 20 h. Preliminary experiments carried out in acidic media without Cr(VI) have shown that some pyrite dissolution occurred. Then, metal species concentration changes with time during pyrite oxidation by Cr(VI) solutions exhibited two distinct trends depending on the complete or incomplete Cr(VI) removal. As long as chromate existed in solution, the Cr-(Ill) to Fe(lIl) ratio was found to be an effective parameter to investigate the pyrite reaction stoichiometry with Cr(VI). Experimental values close to 2 suggest that sulfur compounds with oxidation states between 0 and 2 should be formed during pyrite oxidation by Cr(VI). If Cr(VI) was completely reduced from solution, then the pyrite oxidation by Fe(lll) ions took place to generate ferrous ions.