Design and Validation of a Research-Grade Waterpipe Equipped With Puff Topography Analyzer.

INTRODUCTION: Worldwide, commercially available waterpipes vary widely in design and durability, including differences in fabrication materials, degree of leak-tight fit, and flow path diameter. Little is known about how the components of the waterpipe may influence puffing behavior and user's exposure to toxins. To systematically evaluate exposure, it is necessary to use a standardized research-grade waterpipe (RWP) when conducting clinical and laboratory-based trials. METHODS: We developed a RWP that is configured with an in-line topography system which allows real-time measurement and recording of the smoke volume drawn through the RWP. The RWP was calibrated across the flow rate range expected for waterpipe tobacco smoking and the calibration was verified for known puff volumes using a smoking machine. Operation of the RWP was qualified in a cohort of experienced waterpipe smokers, each smoker using the RWP ad libitum in a laboratory setting while smoker topography and subjective effects data were collected. RESULTS: RWP machine smoking was highly reproducible and yielded puff volumes that agreed well with true values. User acceptance was comparable, and puffing behavior was similar in pattern, with more frequent puffing in the beginning of the session, but significantly different in intensity from that used to estimate the majority of toxicant exposure reported in the literature. CONCLUSIONS: The RWP operates with known precision and accuracy and is well accepted by experienced smokers. This tool can be used to determine the extent to which puffing behaviors are affected by the waterpipe design, components, and/or accessories, tobacco nicotine content, sweet flavorings and/or additives known to increase addictiveness. IMPLICATIONS: This study describes a standardized RWP, equipped with a puffing topography analyzer, which can operate with known precision and accuracy, and is well-accepted by experienced smokers in terms of satisfaction and reward. The RWP is an important tool for determining if puffing behaviors, and thus estimated toxin exposures, are affected by the waterpipe design, components, and/or accessories, tobacco nicotine content, sweet flavorings, and/or additives that are known to increase addictiveness.

Comparison of True and Smoothed Puff Profile Replication on Smoking Behavior and Mainstream Smoke Emissions.

To estimate exposures to smokers from cigarettes, smoking topography is typically measured and programmed into a smoking machine to mimic human smoking, and the resulting smoke emissions are tested for relative levels of harmful constituents. However, using only the summary puff data--with a fixed puff frequency, volume, and duration--may underestimate or overestimate actual exposure to smoke toxins. In this laboratory study, we used a topography-driven smoking machine that faithfully reproduces a human smoking session and individual human topography data (n = 24) collected during previous clinical research to investigate if replicating the true puff profile (TP) versus the mathematically derived smoothed puff profile (SM) resulted in differences in particle size distributions and selected toxic/carcinogenic organic compounds from mainstream smoke emissions. Particle size distributions were measured using an electrical low pressure impactor, the masses of the size-fractionated fine and ultrafine particles were determined gravimetrically, and the collected particulate was analyzed for selected particle-bound, semivolatile compounds. Volatile compounds were measured in real time using a proton transfer reaction-mass spectrometer. By and large, TP levels for the fine and ultrafine particulate masses as well as particle-bound organic compounds were slightly lower than the SM concentrations. The volatile compounds, by contrast, showed no clear trend. Differences in emissions due to the use of the TP and SM profiles are generally not large enough to warrant abandoning the procedures used to generate the simpler smoothed profile in favor of the true profile.

Exploring the effects of pulsed ultrasound at 205 and 616 kHz on the sonochemical degradation of octylbenzene sulfonate.

Compared to continuous wave (CW) ultrasound, pulsed wave (PW) ultrasound has been shown to result in enhanced sonochemical degradation of octylbenzene sulfonate (OBS). However, pulsed ultrasound was investigated under limited pulsing conditions. In this study, pulse-enhanced degradation of OBS was investigated over a broad range of pulsing conditions and at two ultrasonic frequencies (616 and 205 kHz). The rate of OBS degradation was compared to the rate of formation of 2-hydroxyterephthalic acid (HTA) following sonolysis of aqueous terephthalic acid (TA) solutions. This study shows that sonication mode and ultrasound frequency affect both OBS degradation and HTA formation rates, but not necessarily in the same way. Unlike TA, OBS, being a surface active solute, alters the cavitation bubble field by adsorbing to the gas/solution interface of cavitation bubbles. Enhanced OBS degradation rates during pulsing are attributed to this adsorption process. However, negative or smaller pulse enhancements compared to enhanced HTA formation rates are attributed to a decrease in the high-energy stable bubble population and a corresponding increase in the transient bubble population. Therefore, sonochemical activity as determined from TA sonolysis cannot be used as a measure of the effect of pulsing on the rate of degradation of surfactants in water. Over relatively long sonolysis times, a decrease in the rate of OBS degradation was observed under CW, but not under PW conditions. We propose that the generation and accumulation of surface active and volatile byproducts on the surface and inside of cavitation bubbles, respectively, during CW sonolysis is a contributing factor to this effect. This result suggests that there are practical applications to the use of pulsed ultrasound as a method to degrade surface active contaminants in water.