Plastic breath: Quantification of microplastics and polymer additives in airborne particles.

The widespread extensive use of synthetic polymers has led to a substantial environmental crisis caused by plastic pollution, with microplastics detected in various environments and posing risks to both human health and ecosystems. The possibility of plastic fragments to be dispersed in the air as particles and inhaled by humans may cause damage to the respiratory and other body systems. Therefore, there is a particular need to study microplastics as air pollutants. In this study, we tested a combination of analytical pyrolysis, gas chromatography-mass spectrometry, and gas and liquid chromatography-mass spectrometry to identify and quantify both microplastics and their additives in airborne particulate matter and settled dust within a workplace environment: a WEEE treatment plant. Using this combined approach, we were able to accurately quantify ten synthetic polymers and eight classes of polymer additives. The identified additives include phthalates, adipates, citrates, sebacates, trimellitates, benzoates, organophosphates, and newly developed brominated flame retardants.

Studies of Potential Migration of Hazardous Chemicals from Sustainable Food Contact Materials.

In recent years, due to modern techniques for the distribution, transport, and retail sale of food, the production of large amounts of non-biodegradable and bioaccumulative packaging waste has become a major environmental issue. To address this issue, new food packaging materials based on renewable biomass have been studied as eco-friendly, biodegradable, and biocompatible alternatives to synthetic materials. However, although these materials are not petrochemical derivatives, the presence of contaminants cannot be excluded. This work aims to extend the knowledge on bio-based packaging materials, researching the presence of contaminants potentially able to migrate to food at concentrations of concern. In this study, we focus on two classes of contaminants, organophosphate esters (OPEs) and perfluoroalkyl substances (PFASs), carrying out migration tests toward different simulants, according to the current European regulation. PFAS analysis was performed using high-resolution liquid chromatography coupled to ion trap-tandem mass spectrometry (QTrap). OPE analyses were performed both by gas chromatography-mass spectrometry (GC-MS) and high-resolution liquid chromatography coupled to triple quadrupole mass spectrometry (TQMS). Preliminary findings demonstrate the release of toxic OPEs and PFASs from bio-based food packaging, highlighting the need to investigate the presence of potentially harmful chemicals in these materials.

Concentrations and co-occurrence of 101 emerging and legacy organic pollutants in the ultrafine, fine and coarse fractions of airborne particulates associated with treatment of waste from electrical and electronic equipment.

Occupational exposure to airborne particles can increase the development of morbidity, also because of the chemical composition of particulate matter (PM). In workplace, where manual and mechanical disassembly of electric and electronic equipment (EEE) take place, there are evident risks of respiratory exposure to a great number of different toxic organic compounds present in the electrical and plastic materials of which the equipment is made. Airborne particles are numerous, cover a wide range of sizes and are rich in toxic organic compounds. In the present work, a sampling program was conducted and ultrafine, fine and coarse airborne particles were collected in three EEE waste treatment plants. Afterwards, the extraction and analysis of polycyclic aromatic hydrocarbons (PAHs), their nitro and oxygenated derivatives (nitroPAHs, oxyPAHs), organophosphorus compounds (OPEs), Brominated Flame Retardants (BFRs), polychlorinated biphenyls (PCBs), Polybrominated Diphenyl Ethers (PBDEs), and polyfluoralkyl substances (PFASs) was performed. The percentage ratio of the mass of organic compounds and the mass of the ultrafine fraction of PM (PM0.1) was higher than those of the fine and coarse fractions. Even with low concentrations, the co-occurrence of numerous potentially toxic compounds capable of easily reaching other organs passing by the lung vasculature, through the lymph makes the working environment unhealthy.

Occurrence and migration study of chemicals from baking paper and aluminium foil.

The present work focused on the development of an analytical method suitable to study the presence and the release of organophosphate esters (OPEs) and perfluoroalkylated substances (PFASs) from food contact materials (FCMs), from baking paper and aluminium foil. Although these classes of compounds are attracting increasing attention due to their toxicity the knowledge is still insufficient. The extent of their migration from FCMs to food was estimated using different liquid simulants. Ethanol 95 % was used to simulate the contact with fatty food, whilst acetic acid 3 % to mime contact with acidic aqueous-based food and the contact mode involved the use of the ultrasound-assisted technique. Preliminary results showed the higher migration for baking paper samples in contact with aqueous simulant with contaminations in the ranges 78.30-413.21 ng/dm2 and 1.43-13.87 ng/dm2 for OPEs and PFASs respectively. These findings highlighting the need to monitor particularly OPEs in FCMs.

Characterization of organophosphate esters (OPEs) and polyfluoralkyl substances (PFASs) in settled dust in specific workplaces.

An analytical method for detecting flame retardants was slightly modified and optimized for the simultaneous determination of 11 organophosphate esters (OPEs) and 26 polyfluoralkyl substances (PFASs) contained in dust. All the analytes were determined in HPLC/MS-MS, and OPEs were also analyzed in GC/MS, and the results were compared. The study was conducted through the investigation of the Standard Reference Material SRM 2585 of the National Institute of Standard and Technology (NIST). The results were compared with the available reference mass fraction reported in the NIST certificate. The mass fraction obtained for the other OPEs and PFASs was compared to available data in the literature. After verifying the reliability of the results, the method was applied to environmental samples of settled dust, collected in four workplaces, where OPE and PFAS content is expected to be higher than in house dust: a mechanical workshop, an electronic repair center, a disassembly site, and a shredding site of two electronic waste recycling plants. By analyzing both PFASs and OPEs in the same samples, the present work demonstrated that the selected working places were more polluted in OPEs than houses; on the contrary, PFAS content in house dust proved to be more than ten times higher than that in workplaces. Additional research is necessary to confirm these data. Nevertheless, because this preliminary study showed not negligible concentrations of OPEs in some workplaces and of PFASs in houses, their monitoring should be extended to other domestic and selected working sites.

Comparison of analytical approaches for identifying airborne microorganisms in a livestock facility.

An intensive study, applied to a site characterized by multiple sources of microorganisms, was aimed at understanding the best approach to study bioaerosol. Culture-based, molecular biological, and chemical methods were applied to Particulate Matter (PM) samples collected in a livestock facility, during spring and autumn seasons, in two different outdoor areas. The first one was close to a place where feed was stored and handled and the second next to an open cowshed. Qualitative analysis of bacteria was performed by sequencing techniques applied to DNA extracted from both isolated culturable bacteria and particulate matter samples. Quantification of microorganisms was achieved through three distinct approaches. Microorganism colonies were counted, after incubation at 28 °C, and expressed as colony-forming units (CFU) per m3. Chemical method consisted in the identification of individual biomarkers, and their conversion to number of microorganisms per m3, using proper conversion factors. Finally, qPCR was applied to DNA extracted from PM samples, and the results were expressed as total amount of bacteria present in the bioaerosol (UG/m3). The presence of airborne sterols was also studied to broaden the knowledge of bioaerosol components in atmosphere. Small seasonal differences and major sampling site differences occurred. Obviously, culture-dependent method identified less and different bacteria, than culture-independent approach. The chemical approach and the culture independent metagenomic method were in good agreement. As expected, CFU/m3 accounted for not more than 0.3% of bacteria calculated as the average of chemical and culture independent metagenomic methods. The complexity of the obtained results shows that the different approaches are complementary to obtain an exhaustive description of bioaresol in terms of concentration, speciation, viability, pathogenicity.

Toxic Organic Contaminants in Airborne Particles: Levels, Potential Sources and Risk Assessment.

In the last years, many studies have focused on risk assessment of exposure of workers to airborne particulate matter (PM). Several studies indicate a strong correlation between PM and adverse health outcomes, as a function of particle size. In the last years, the study of atmospheric particulate matter has focused more on particles less than 10 µm or 2.5 µm in diameter; however, recent studies identify in particles less than 0.1 µm the main responsibility for negative cardiovascular effects. The present paper deals with the determination of 66 organic compounds belonging to six different classes of persistent organic pollutants (POPs) in the ultrafine, fine and coarse fractions of PM (PM < 0.1 µm; 0.1 < PM < 2.5 µm and 2.5 < PM < 10 µm) collected in three outdoor workplaces and in an urban outdoor area. Data obtained were analyzed with principal component analysis (PCA), in order to underline possible correlation between sites and classes of pollutants and characteristic emission sources. Emission source studies are, in fact, a valuable tool for both identifying the type of emission source and estimating the strength of each contamination source, as useful indicator of environment healthiness. Moreover, both carcinogenic and non-carcinogenic risks were determined in order to estimate human health risk associated to study sites. Risk analysis was carried out evaluating the contribution of pollutant distribution in PM size fractions for all the sites. The results highlighted significant differences between the sites and specific sources of pollutants related to work activities were identified. In all the sites and for all the size fractions of PM both carcinogenic and non-carcinogenic risk values were below acceptable and safe levels of risks recommended by the regulatory agencies.

Characterization of seven sterols in five different types of cattle feedstuffs.

This paper provides a method for the quantification of sterols in different types of calf feedstuffs based on soy, sunflower, hay, calf feed and a mixture of all of them. The free fraction and the total sterolic fraction, after saponification and acidic hydrolysis of the samples, are extracted by solvent and the sterols are identified/quantified by reversed phase HPLC coupled to tandem mass spectrometry by atmospheric pressure chemical ionization. After the recovery evaluation, the method is validated in terms of linearity (coefficient of determination R2), repeatability (coefficient of variation RSD), limit of detection and quantification. In most of the cases, the most representative phytosterol is ß-sitosterol, followed by campesterol or stigmasterol and by other minor sterols such as fucosterol, and Δ-5-avenasterol. In addition, also cholesterol and ergosterol, if present, are evaluated in all the samples. As far as we know, very little information is available on the investigated feeds, which are commonly used on farms. The results of this survey were compared to other studies, if present in literature, showing good agreement. The proposed method resulted to be simple, fast and suitable for application to other sterols, feedstuffs and derived foods. The knowledge of the sterolic content and composition is getting more and more important, both in terms of comprehension of the vegetal biochemistry and as basis for sterolomic studies.

Occurrence of Halogenated Pollutants in Domestic and Occupational Indoor Dust.

The occurrence of halogenated organic pollutants in indoor dust can be high due to the presence of textile, electronic devices, furniture, and building materials treated with these chemicals. In this explorative study, we focused on emerging organic pollutants, such as novel brominated flame retardants (nBFRs) and some perfluoroalkyl substances, together with legacy polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (BDEs) in settled dust collected in houses and workplaces such as one office and two electrotechnical and mechanical workshops. The total contribution of the investigated pollutants was lower in house and in office dusts except for few nBFRs (such as bis (2-ethylhexyl)-3,4,5,6-tetrabromo-phthalate at a concentration of 464.5 ng/g in a house and hexachlorocyclopentadienyldibromocyclooctane at 40.4 ng/g in the office), whereas in electrotechnical and mechanical workshops a high incidence of PCBs, BDEs, and nBFRs occurred (for example, BDE 209 at a concentration of 2368.0 ng/g and tetrabromobisphenol A at 32,320.1 ng/g in electrotechnical and mechanical workshops). Estimated daily intakes were also calculated, showing that domestic and occupational environments can lead to a similar contribution in terms of human exposure. The higher exposure contribution was associated to nBFRs, whose EDIs were in the range of 3968.2-555,694.2 pg/kg bw/day. To provide a complete view about the indoor contamination, in this investigation, we also included polycyclic aromatic hydrocarbons (PAHs) and their oxygenated and nitrated derivatives. Definitely, dust collection represents a simple, fast, and cost-effective sampling and dust contamination level can be a useful indicator of environment healthiness. Besides, the presented method can be a smart tool to provide a time and money saving technique to characterize 99 pollutants thanks to a single sample treatment.

Polychlorinated Biphenyl Profile in Polyhydroxy-alkanoates Synthetized from Urban Organic Wastes.

The microbial synthesis of polyhydroxyalkanoates (PHA) from organic wastes is a valuable process to valorize available renewable resources, such as food wastes and biological sludge. Bioplastics find many applications in various sectors, from medical field to food industry. However, persistent organic pollutants could be transferred from wastes to the final product. The present paper demonstrates that the use of municipal wastes in PHA production is safe for the environment and human health and provides a polychlorinated biphenyl (PCB) profile in both commercial and waste-based PHA samples. PCB analysis in several PHA samples showed very low concentrations of the target analytes. Commercial PHA samples showed a similar PCB level with respect to PHA samples from municipal waste/sludge and higher than PHA samples from fruit waste. For all analyzed PCBs, detected concentrations were consistently lower than the ones reported in regulatory framework or guidelines.

A Rapid and Accurate Method for the Determination of Methylxanthines in Different Nervous System Stimulant Beverages.

Background: Caffeine, theophylline, and theobromine are methylxanthines commonly found in coffee, tea, cola, and cocoa. Other sources may be soft drinks or energy drinks. All of them are stimulants of the nervous system and can be used for the treatment of some diseases. The three xanthines produce addiction with typical abstinence symptoms. Among young people, the consumption of energy beverages is increasing, and the growing market causes concern about the caffeine intake. To evaluate intake of methylxanthines, their accurate determination can be helpful. Methods: A simple method for their determination without sample pretreatment was applied to beverages, including coffee, tea, cola, and energy drinks. The separation was achieved by LC with UV detection. The method was validated in terms of linearity, LOD and LOQ, accuracy, and reproducibility. Results: The drinks were directly injected after a filtration, and no matrix effect was demonstrated. The procedure proved to be simple, time saving, accurate, and reproducible and may be recommended for reliable assays in routine work. The investigated samples showed a range of caffeine concentration from 100 to 3050 mg/L. Possible intake of methylxanthines from miscellaneous types of drinks was assessed considering the European Food Safety Authority Opinion on the safety of caffeine consumption. Our results were in good agreement with other authors. Conclusions: A fast and accurate method for the simultaneous determination of three xanthynes in beverages was validated. The selected strategy has proved to be fit-for-purpose by applying it to different nervous system stimulant drinks. Highlights: A simple and time saving procedure was proposed for the separation, detection, and quantitation of three methylxantynes in nervous system stimulant drinks. No sample preparation was needed, and speculation could be made about the possible intake of them from beverages.

Evaluation of Bioaerosol Bacterial Components of a Wastewater Treatment Plant Through an Integrate Approach and In Vivo Assessment.

Wastewater carries different pathogenic and non-pathogenic microorganisms that can be dispersed in the surrounding environment. Workers who frequent sewage treatment plants can therefore be exposed to aerosols that contain a high concentration of potentially dangerous biological agents, or they can come into direct contact with contaminated material. This can lead to allergies, infections and occupational health-associated diseases. A characterization of biological risk assessment of bioaerosol exposure is necessary. The aim of this study was to evaluate the application of an interdisciplinary method that combines chemical and biological approaches for the analysis of a bioaerosol derived from a wastewater treatment plant (WWTP) situated in Italy. Sampled filters were analyzed by HPLC-MS/MS spectroscopy that searched for different chemical biomarkers of airborne microorganisms. The analytical quantification was compared to the biological cultural method that revealed an underrated microbial concentration. Furthermore, next generation sequencing analysis was used also to identify the uncultivable species that were not detected by the culture dependent-method. Moreover, the simple animal model Caenorhabditis elegans was used to evaluate the pathogenicity of two isolates-Acinetobacter iwoffii and Micrococcus luteus-that showed multidrug-resistance. This work represents a starting point for the development of a multidisciplinary approach for the validation of bioaerosol exposure on WWTP workplaces.

Hydrophilic Interaction Liquid Chromatography-Tandem Mass Spectrometry Analysis of Fosetyl-Aluminum in Airborne Particulate Matter.

Fosetyl-aluminum is a synthetic fungicide administered to plants especially to prevent diseases caused by the members of the Peronosporales and several Phytophthora species. Herein, we present a selective liquid chromatography-tandem mass spectrometry (LC-MS/MS) method to analyze residues of fosetyl-A1 in air particulate matter. This study was performed in perspective of an exposure assessment of this substance of health concern in environments where high levels of fosetly-Al, relatively to airborne particulate matter, can be found after spraying it. The cleanup procedure of the analyte, from sampled filters of atmospheric particulate matter, was optimized using a Strata X solid-phase extraction cartridge, after accelerated extraction by using water. The chromatographic separation was achieved using a polymeric column based on hydrophilic interaction in step elution with water/acetonitrile, whereas the mass spectrometric detection was performed in negative electrospray ionization. The proposed method resulted to be a simple, fast, and suitable method for confirmation purposes.

Semiautomatic sequential extraction of polycyclic aromatic hydrocarbons and elemental bio-accessible fraction by accelerated solvent extraction on a single particulate matter sample.

We describe the optimization and validation of a sequential extractive method for the determination of the polycyclic aromatic hydrocarbons (PAHs) and elements (Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Se, V and Zn) that are chemically fractionated into bio-accessible and mineralized residual fractions on a single particulate matter filter. The extraction is performed by automatic accelerated solvent extraction (ASE); samples are sequentially treated with dichloromethane/acetone (4:1) for PAHs extraction and acetate buffer (0.01M; pH 4.5) for elements extraction (bio-accessible fraction). The remaining solid sample is then collected and subjected to acid digestion with HNO3:H2O2 (2:1) to determine the mineralized residual element fraction. We also describe a homemade ASE cell that reduces the blank values for most elements; in this cell, the steel frit was replaced by a Teflon pierced disk and a Teflon cylinder was used as the filler. The performance of the proposed method was evaluated in terms of recovery from standard reference material (SRM 1648 and SRM 1649a) and repeatability. The equivalence between the new ASE method and conventional methods was verified for PAHs and for bio-accessible and mineralized residual fractions of elements on PM10 twin filters.

Muramic and dipicolinic acids in atmospheric particulate matter as biomarkers of bacteria and bacterial spores.

Airborne bacteria are components of the atmospheric aerosol particles and can be responsible of allergic disease, regardless of their viability. In this paper, we report a method for the determination of total (viable and nonviable) bacterial content in airborne particles, using muramic and dipicolinic acids as biomarkers of bacteria and bacterial spores, respectively. The analytical procedure was optimized with bacteria and spores of Bacillus subtilis. After extraction and purification, the two biomarkers were analyzed by HPLC-ESI-MS/MS and their percentage was evaluated to be used as conversion factor. The present method for the determination of the total bacterial content was then applied to environmental samples, after a proper collection in an urban site. Thanks to the use of a low pressure impactor, capable of fractionating particles into the range of 0.03-10 µm, it was also possible to study the bacterial content in ultrafine, fine, and coarse particulate matter. The results from this study showed that muramic and dipicolinic acids can be determined together in one chromatographic run in reversed phase ion pair chromatography. Bacteria were more abundant than bacterial spores in the urban atmosphere, both showing a higher concentration in the coarse fraction of particles, although bacteria and bacterial spore amounts per unit mass of ultrafine particles were higher than in fine and coarse particles.

Development of a method for the analysis of underivatized amino acids by liquid chromatography/tandem mass spectrometry: application on Standard Reference Material 1649a (urban dust).

A liquid chromatography-tandem mass spectrometry analytical procedure has been developed for the detection and quantitative determination of underivatized amino acids at low concentrations in a Standard Reference Material-urban dust. In order to minimize interferences of other compounds, an accelerated solvent extraction followed by a solid phase extraction on two different cartridges was applied prior to LC-MS-MS. Fourteen amino acids were separated by high resolution liquid chromatography, detected and quantified by multiple reaction monitoring on a triple quadrupole. The proposed methodology has been applied for the first time on Standard Reference Material 1649a (urban dust) from the National Institute of Standards and Technology, that does not report certification values for these compounds. This methodology avoids the derivatization step and allows the amino acid quantification in a complex matrix, such as that of atmospheric particulate matter, and represent a good method suitable to analyze this class of compounds in atmospheric aerosol. The selected strategy demonstrated to be fit-for-purpose, by applying it to a real atmospheric sample with the aim to verify the efficacy of the study and to provide information about the organic matter content.

Extraction and analysis of fungal spore biomarkers in atmospheric bioaerosol by HPLC-MS-MS and GC-MS.

Airborne microorganisms, as bacteria and fungi, are ubiquitous components of the atmospheric aerosol particles. In this paper, we report a method for the simultaneous extraction, purification, separation, identification and quantification of ergosterol, mannitol and arabitol as biomarkers of fungal spores in bioaerosol particles. After sampling by a low volume sampler, filters were spiked with mannitol-(13)C and dehydrocholesterol as internal standards. Samples were then extracted by accelerated solvent extraction using pure ethanol. The extract was then passed through an amino cartridge and divided in two parts: the apolar fraction, released from the cartridge, was subjected to liquid liquid extraction (by n-hexane), while polar compounds, retained by the cartridge, were eluted by a mixture of methanol-water. The two fractions were joined and analyzed by HPLC equipped with two different columns in series, and coupled to a triple-quadrupole mass spectrometer with Atmospheric Pressure Chemical Ionization source. In addition, the same fractions were analyzed, after derivatization, by GC-MS. The results obtained by the two techniques were finally compared, showing good agreement between them. Last, the contents of the three biomarkers have been estimated in three atmospheric samples collected in a suburban/rural site and, using literature conversion factors, correlated to fungal biomass.

Characterization and distribution of petroleum hydrocarbons and heavy metals in groundwater from three Italian tank farms.

The present paper highlights the utility of petroleum chemical fingerprinting in investigating known or suspected tank farm releases. A detailed characterization of groundwater was carried out in three tank farms located in north, central and south Italy. Eighteen parent polycyclic aromatic hydrocarbons (naphthalene through coronene), n-alkanes (n-C(10) through n-C(36)), isoprenoids pristane and phytane, vanadium, nickel and lead were determined. Distribution profiles and diagnostic ratios of specific fuel constituents were studied in order to identify contamination sources. Data analysis shows that in the study sites multiple pollutant sources affecting the tank farms and the surrounding industrial areas are present. Both high concentrations of contaminants coming from fuel releases and noticeable concentrations of biogenic compounds were found. A detailed data analysis suggests the origin and the level of pollution of the three sites. The results demonstrate that threshold concentration approach is not always sufficient and it is necessary to carry out studies of contaminant distribution and their diagnostic ratios in order to perform a successful forensic investigation.

Air pollutants and the characterization of the organic content of aerosol particles in a mixed industrial/semi-rural area in central Italy.

Both regulated and unregulated air pollutants were detected during an intensive seasonal sampling campaign in a mixed industrial/semi-rural area on the outskirts of Rome, Italy, at two sites located opposite a hospital waste incinerator, downwind according to the direction of the prevailing local winds. Concentrations of pollutants were significantly lower than in urban atmospheres. The composition of particulate organic material indicated a heavy biogenic impact, accompanied by a lower contribution from petroleum-related processes. Both PAH and nitro-PAH group compositions of particulates were used to assess the nature and relative importance of sources. Both sites showed that different and diffuse sources contributed to local pollution with a significant contribution from traffic, proving that the hospital waste incinerator was not the main pollution source in this area. Among unregulated compounds, a series of positional isomers of nitro-PAHs and other organic compounds associated with particulate matter were investigated. In particular, 1- and 3-nitrophenanthrene identification was carried out, and they proved to be the most abundant nitro-PAHs.

Data quality of PAH determinations in environmental monitoring.

The sources of uncertainty affecting measurements of pollutants include sample collection, handling and stocking, and analytical procedure. With regard to chemical analysis, MS detection offers a series of advantages for resolving complex mixtures and identify and quantify analytes present at very small extents. Nevertheless, it presents some problems of reproducibility, which can affect the quality of quantitative data. PAH represent key-compounds among atmospheric pollutants and are usually evaluated by means of dedicated methods comprising MS detection. Based upon the above considerations, an analytical method has been standardized, suitable for determining PAH in atmospheric aerosols and diesel particulate exhausts. To test the procedure, both diesel particulate and urban aerosol NIST reference materials (SRM-2975 and SRM-1649A, respectively) have been processed and the results have been compared with certified and/or literature data. The results obtained are shortly discussed.