Graphene as an efficient interfacial layer for electrochromic devices.

This study presents an interfacial modification strategy to improve the performance of electrochromic films that were fabricated by a magnetron sputtering technique. High-quality graphene sheets, synthesized by chemical vapor deposition, were used to modify fluorine-doped tin oxide substrates, followed by the deposition of high-performance nanocomposite nickel oxide electrochromic films. Electrochromic cycling results revealed that a near-complete monolayer graphene interfacial layer improves the electrochromic performance in terms of switching kinetics, activation period, coloration efficiency, and bleached-state transparency, while maintaining ∼100% charge reversibility. The present study offers an alternative route for improving the interfacial properties between electrochromic and transparent conducting oxide films without relying on conventional methods such as nanostructuring or thin film composition control.

Atomic layer deposition of amorphous TiO2 on graphene as an anode for Li-ion batteries.

Atomic layer deposition (ALD) was used to deposit TiO2 anode material on high surface area graphene (reduced graphene oxide) sheets for Li-ion batteries. An Al2O3 ALD ultrathin layer was used as an adhesion layer for conformal deposition of the TiO2 ALD films at 120 ° C onto the conducting graphene sheets. The TiO2 ALD films on the Al2O3 ALD adhesion layer were nearly amorphous and conformal to the graphene sheets. These nanoscale TiO2 coatings minimized the effect of the low diffusion coefficient of lithium ions in bulk TiO2. The TiO2 ALD films exhibited stable capacities of ~120 mAh g(-1) and ~100 mAh g(-1) at high cycling rates of 1 A g(-1) and 2 A g(-1), respectively. The TiO2 ALD films also displayed excellent cycling stability with ~95% of the initial capacity remaining after 500 cycles. These results illustrate that ALD can provide a useful method to deposit electrode materials on high surface area substrates for Li-ion batteries.

Origin of electrochromism in high-performing nanocomposite nickel oxide.

Electrochromic effects of transition metal oxides provide a great platform for studying lithium intercalation chemistry in solids. Herein, we report on an electronically modified nanocomposite nickel oxide (i.e., Li2.34NiZr0.28Ox) that exhibits significantly improved electrochromic performance relative to the state-of-the-art inorganic electrochromic metal oxides in terms of charge/discharge kinetics, bleached-state transparency, and optical modulation. The knowledge obtained from O K-edge X-ray absorption spectroscopy (XAS) and X-ray photoelectron spectroscopy (XPS) suggests that the internally grown lithium peroxide (i.e., Li2O2) species plays a major role in facilitating charge transfer thus enabling optimal electrochromic performance. This understanding is relevant to recent theoretical studies concerning conductivity in Li2O2 for lithium-air batteries (as cited in the main text). Furthermore, we elucidate the electrochromism in modified nickel oxide in lithium ion electrolyte with the aid of Ni K-edge XAS and Ni L-edge XAS studies. The electrochromism in the nickel oxide materials arises from the reversible formation of hole states on the NiO6 units, which then impacts the Ni oxidation state through the Ni3d-O2p hybridization states. This study sheds light on the lithium intercalation chemistry for general energy storage and semiconductor applications.

Hole doping in Al-containing nickel oxide materials to improve electrochromic performance.

Electrochromic materials exhibit switchable optical properties that can find applications in various fields, including smart windows, nonemissive displays, and semiconductors. High-performing nickel oxide electrochromic materials have been realized by controlling the material composition and tuning the nanostructural morphology. Post-treatment techniques could represent efficient and cost-effective approaches for performance enhancement. Herein, we report on a post-processing ozone technique that improves the electrochromic performance of an aluminum-containing nickel oxide material in lithium-ion electrolytes. The resulting materials were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), ultraviolet-visible-near-infrared (UV-vis-NIR) spectroscopy, and X-ray absorption spectroscopy (XAS). It was observed that ozone exposure increased the Ni oxidation state by introducing hole states in the NiO(6) octahedral unit. In addition, ozone exposure gives rise to higher-performing aluminum-containing nickel oxide films, relative to nickel oxide containing both Al and Li, in terms of switching kinetics, bleached-state transparency, and optical modulation. The improved performance is attributed to the decreased crystallinity and increased nickel oxidation state in aluminum-containing nickel oxide electrochromic films. The present study provides an alternative route to improve electrochromic performance for nickel oxide materials.

Low-temperature ozone exposure technique to modulate the stoichiometry of WOx nanorods and optimize the electrochromic performance.

A low-temperature ozone exposure technique was employed for the post-treatment of WO(x) nanorod thin films fabricated from hot-wire chemical vapor deposition (HWCVD) and ultrasonic spray deposition (USD) techniques. The resulting films were characterized with x-ray diffraction (XRD), transmission electron microscopy (TEM), Raman spectroscopy, UV-vis-NIR spectroscopy and x-ray photoelectron spectroscopy (XPS). The stoichiometry and surface crystallinity of the WO(x) thin films were subsequently modulated upon ozone exposure and thermal annealing without particle growth. The electrochromic performance was studied in a LiClO(4)-propylene carbonate electrolyte, and the results suggest that the low-temperature ozone exposure technique is superior to the traditional high-temperature thermal annealing (employed to more fully oxidize the WO(x)). The optical modulation at 670 nm was improved from 35% for the as-deposited film to 57% for the film after ozone exposure at 150 °C. The coloration efficiency was improved and the switching speed to the darkened state was significantly accelerated from 18.0 s for the as-deposited film to 11.8 s for the film after the ozone exposure. The process opens an avenue for low-temperature and cost-effective manufacturing of electrochromic films, especially on flexible polymer substrates.

Using atomic layer deposition to hinder solvent decomposition in lithium ion batteries: first-principles modeling and experimental studies.

Passivating lithium ion (Li) battery electrode surfaces to prevent electrolyte decomposition is critical for battery operations. Recent work on conformal atomic layer deposition (ALD) coating of anodes and cathodes has shown significant technological promise. ALD further provides well-characterized model platforms for understanding electrolyte decomposition initiated by electron tunneling through a passivating layer. First-principles calculations reveal two regimes of electron transfer to adsorbed ethylene carbonate molecules (EC, a main component of commercial electrolyte), depending on whether the electrode is alumina coated. On bare Li metal electrode surfaces, EC accepts electrons and decomposes within picoseconds. In contrast, constrained density functional theory calculations in an ultrahigh vacuum setting show that, with the oxide coating, e(-) tunneling to the adsorbed EC falls within the nonadiabatic regime. Here the molecular reorganization energy, computed in the harmonic approximation, plays a key role in slowing down electron transfer. Ab initio molecular dynamics simulations conducted at liquid EC electrode interfaces are consistent with the view that reactions and electron transfer occur right at the interface. Microgravimetric measurements demonstrate that the ALD coating decreases electrolyte decomposition and corroborates the theoretical predictions.

Ultrathin coatings on nano-LiCoO2 for Li-ion vehicular applications.

To deploy Li-ion batteries in next-generation vehicles, it is essential to develop electrodes with durability, high energy density, and high power. Here we report a breakthrough in controlled full-electrode nanoscale coatings that enables nanosized materials to cycle with durable high energy and remarkable rate performance. The nanoparticle electrodes are coated with Al(2)O(3) using atomic layer deposition (ALD). The coated nano-LiCoO(2) electrodes with 2 ALD cycles deliver a discharge capacity of 133 mAh/g with currents of 1400 mA/g (7.8C), corresponding to a 250% improvement in reversible capacity compared to bare nanoparticles (br-nLCO), when cycled at this high rate. The simple ALD process is broadly applicable and provides new opportunities for the battery industry to design other novel nanostructured electrodes that are highly durable even while cycling at high rate.

First-Principles Study of Lithium Borocarbide as a Cathode Material for Rechargeable Li ion Batteries.

Computational simulations within density functional theory are performed to investigate the potential application of a lithium borocarbide (LiBC) compound as a unique material for lithium ion batteries. The graphene-like BC sheets are predicted to be Li(+) intercalation hosts with the Li ion capacity surprisingly surpassing that of graphite. Here, the layered LixBC structure is preserved with x ≥ 0.5, indicating that half of the Li ions in the LiBC compound are rechargeable. Furthermore, the intercalation potential (equilibrium lithium-insertion voltage of 2.3-2.4 V relative to lithium metal) is significantly higher than that in graphite, allowing Li0.5BC to function as a cathode material. The reversible electrochemical reaction, LiBC ⇌ Li0.5BC + 0.5Li, enables a specific energy density of 1088 W h/kg and a volumetric energy density of 2463 W h/L. The volume change is less than 3% during the charging and discharging process. This discovery could lead to the development of a unique high-capacity LiBC Li ion cathode material.

Solid-state 13C NMR assignment of carbon resonances on metallic and semiconducting single-walled carbon nanotubes.

Solid-state (13)C NMR spectroscopy was used to investigate the chemical shift of nanotube carbons on m- and s-SWNTs (metallic and semiconducting single-walled nanotubes) for samples with widely varying s-SWNT content, including samples highly enriched with nearly 100% m- and s-SWNTs. High-resolution (13)C NMR was found to be a sensitive probe for m- and s-SWNTs in mixed SWNT samples with diameters of approximately 1.3 nm. The two highly enriched m- and s-SWNT samples clearly exhibited features for m- and s-SNWT (13)C nuclei (approximately 123 and 122 ppm, respectively) and were successfully fit with a single Gaussian, while five mixed samples required two Gaussians for a satisfactory fit.

Conformal surface coatings to enable high volume expansion Li-ion anode materials.

An alumina surface coating is demonstrated to improve electrochemical performance of MoO(3) nanoparticles as high capacity/high-volume expansion anodes for Li-ion batteries. Thin, conformal surface coatings were grown using atomic layer deposition (ALD) that relies on self-limiting surface reactions. ALD coatings were tested on both individual nanoparticles and prefabricated electrodes containing conductive additive and binder. The coated and non-coated materials were characterized using transmission electron microscopy, energy-dispersive X-ray spectroscopy, electrochemical impedance spectroscopy, and galvanostatic charge/discharge cycling. Importantly, increased stability and capacity retention was only observed when the fully fabricated electrode was coated. The alumina layer both improves the adhesion of the entire electrode, during volume expansion/contraction and protects the nanoparticle surfaces. Coating the entire electrode also allows for an important carbothermal reduction process that occurs during electrode pre-heat treatment. ALD is thus demonstrated as a novel and necessary method that may be employed to coat the tortuous network of a battery electrode.

Boron-based organometallic nanostructures: hydrogen storage properties and structure stability.

Transition-metal (TM) boride and carboride nanostructures are studied as model organometallic materials for hydrogen storage. The dispersed TM atoms function as H2 sorption centers on the surface of the boron or carbon-boron substrate. The flexibility offered in the variety of possible structures permits the study of the effect of the TM-TM distance on the storage capacity. When the TMs are too close to one another, TM-TM bonding reduces the capacity. Even when separated by distances larger than the normal TM-TM bond length, delocalization of TM valence electrons can still lower the hydrogen capacity. An optimal TM-TM distance for the structural motifs studied here is approximately 6 A. Our study also permitted the evaluation of new TM boride nanostructures. We predict a low-energy single-walled scandium triboride (ScB3) nanotube that can bind approximately 6.1 wt % hydrogen with a binding energy of 22 approximately 26 kJ/mol.

Multiwall carbon nanotube absorber on a thin-film lithium niobate pyroelectric detector.

Multiwall carbon nanotubes (MWNTs) were applied in a bulk layer to a pyroelectric film to increase the detector sensitivity nearly fourfold without a substantial penalty to the low-frequency response (4-100 Hz). In addition, the spectral sensitivity over the wavelength range from 600 to 1800 nm was uniformly enhanced, with variations less than 1%. The results demonstrate the suitability of MWNTs as an efficient thermal absorber having low thermal mass.

Effects of surfactant and boron doping on the BWF feature in the Raman spectrum of single-wall carbon nanotube aqueous dispersions.

We examine the Breit-Wigner-Fano (BWF) line shape in the Raman spectra of carbon single-wall nanotubes (SWNTs) dispersed in aqueous suspensions. Bundling and electronic effects are studied by comparing undoped SWNTs (C-SWNTs) to boron-doped nanotubes (B-SWNTs) in a variety of different surfactant solutions. For SWNTs dispersed with nonionic surfactants that are less effective in debundling than ionic surfactants, the Raman spectra retain a large BWF feature. However, we demonstrate that even for SWNTs dispersed as isolated nanotubes by ionic surfactants the BWF feature may be present and that the intensity of the BWF is highly sensitive to the specific surfactant. In particular, surfactants with electron-donating groups tend to enhance the BWF feature. Also, modification of the SWNT electronic properties by boron doping leads to enhanced surfactant dispersion relative to undoped C-SWNTs and also to modification of the BWF feature. These observations are in agreement with reports demonstrating an enhancement of the BWF by bundling but also agree with reports that suggest electron donation can enhance the BWF feature even for isolated SWNTs. Importantly, these results serve to caution against using the lack or presence of a BWF feature as an independent measure of SWNT aggregation in surfactant dispersions.

Protonation of carbon single-walled nanotubes studied using 13C and 1H-13C cross polarization nuclear magnetic resonance and Raman spectroscopies.

The reversible protonation of carbon single-walled nanotubes (SWNTs) in sulfuric acid and Nafion was investigated using solid-state nuclear magnetic resonance (NMR) and Raman spectroscopies. Magic-angle spinning (MAS) was used to obtain high-resolution 13C and 1H-13C cross polarization (CP) NMR spectra. The 13C NMR chemical shifts are reported for bulk SWNTs, H2SO4-treated SWNTs, SWNT-Nafion polymer composites, SWNT-AQ55 polymer composites, and SWNTs in contact with water. Protonation occurs without irreversible oxidation of the nanotube substrate via a charge-transfer process. This is the first report of a chemically induced change in a SWNT 13C resonance brought about by a reversible interaction with an acidic proton, providing additional evidence that carbon nanotubes behave as weak bases. Cross polarization was found to be a powerful technique for providing an additional contrast mechanism for studying nanotubes in contact with other chemical species. The CP studies confirmed polarization transfer from nearby protons to nanotube carbon atoms. The CP technique was also applied to investigate water adsorbed on carbon nanotube surfaces. Finally, the degree of bundling of the SWNTs in Nafion films was probed with the 1H-13C CP-MAS technique.

Single-wall carbon nanotube coating on a pyroelectric detector.

Carbon single-wall nanotubes (SWNTs) are studied as the thermal-absorption coating on a large area pyroelectric detector. The SWNTs were produced by a laser vaporization method and dispersed onto the detector surface by use of a simple airbrush technique. The detector was based on a 1-cm-diameter, 60-microm-thick lithium tantalate disk having nickel electrodes. We report the spectral responsivity of the detector ranging from 600 to 1800 nm, as well as the spatial and directional uniformity at 850 nm. Using Drude and Lorentzian dielectric functions and an effective medium approximation to obtain the indices of refraction of semiconductor and metallic SWNTs, we compared the expected theoretical relative responsivity for the two types of tube with the measured relative responsivity of the detector. Values of thermal conductivity, specific heat, and damage threshold obtained from the literature are compared with properties of alternatives for thermal coatings such as gold-black and carbon-based paint.

Experimental Gibbs free energy considerations in the nucleation and growth of single-walled carbon nanotubes.

Gas feed composition and reaction temperature were varied to identify the thermodynamic threshold conditions for the nucleation and growth of SWNT from methane on supported Fe/Mo catalyst. These reaction conditions closely approximate the pseudoequilibrium conditions that lead to the nucleation and growth of SWNT. These measurements also serve to determine an upper limit of the Gibbs free energy of formation for SWNT. The Gibbs free energy of formation relative to graphite is in good agreement with literature values predicted from simulations for SWNT nuclei containing approximately 80 atoms, while considerably larger than that predicted for bulk (5,5) SWNT. Our estimate over the range 700 to 1000 degrees C of 16.1 to 13.9 kJ mol(-1) falls between the results of these simulations and literature values for diamond.

Formation of nanooctahedra in molybdenum disulfide and molybdenum diselenide using pulsed laser vaporization.

Pulsed laser vaporization has been used to produce nanooctahedra of MoS2 and MoSe2. The nanooctahedra primarily form in two- or three-layer nested octahedra, although nesting up to five layers has been observed. Tilting the TEM sample stage and mapping how the images of single particles transformed provided the evidence to verify their octahedral geometry. Analysis of 30 two- and three-layered octahedra showed that their outer edge lengths clustered at approximately 3.8 nm and approximately 5.1 nm, respectively. This discreet sizing and the high symmetry of these closed nanooctahedra represent the closest inorganic analogy yet to the carbon fullerenes. The geometrical implications for forming octahedra from these layered compounds are investigated by considering different atomic arrangements assuming either trigonal prismatic or octahedral coordination around the Mo atom and yields two possible configurations for the actual structure of the nanooctahedra. A preliminary survey of pulsed laser vaporization of other layered metal chalcogenides shows that these dichalcogenides differ in their tendency to form small closed layered fullerene-like structures. These materials can be ranked from highest tendency to lowest as follows: NbSe2, WS2, WSe2, SnS2, TaS2, GaS, ReS2, and MoTe2.

Characterization of the oxygen tolerance of a hydrogenase linked to a carbon monoxide oxidation pathway in Rubrivivax gelatinosus.

A hydrogenase linked to the carbon monoxide oxidation pathway in Rubrivivax gelatinosus displays tolerance to O2. When either whole-cell or membrane-free partially purified hydrogenase was stirred in full air (21% O2, 79% N2), its H2 evolution activity exhibited a half-life of 20 or 6 h, respectively, as determined by an anaerobic assay using reduced methyl viologen. When the partially purified hydrogenase was stirred in an atmosphere containing either 3.3 or 13% O2 for 15 min and evaluated by a hydrogen-deuterium (H-D) exchange assay, nearly 80 or 60% of its isotopic exchange rate was retained, respectively. When this enzyme suspension was subsequently returned to an anaerobic atmosphere, more than 90% of the H-D exchange activity was recovered, reflecting the reversibility of this hydrogenase toward O2 inactivation. Like most hydrogenases, the CO-linked hydrogenase was extremely sensitive to CO, with 50% inhibition occurring at 3.9 microM dissolved CO. Hydrogen production from the CO-linked hydrogenase was detected when ferredoxins of a prokaryotic source were the immediate electron mediator, provided they were photoreduced by spinach thylakoid membranes containing active water-splitting activity. Based on its appreciable tolerance to O2, potential applications of this hydrogenase are discussed.