KIT-5-Assisted Synthesis of Mesoporous SnO2 for High-Performance Humidity Sensors with a Swift Response/Recovery Speed.

Developing highly efficient semiconductor metal oxide (SMOX) sensors capable of accurate and fast responses to environmental humidity is still a challenging task. In addition to a not so pronounced sensitivity to relative humidity change, most of the SMOXs cannot meet the criteria of real-time humidity sensing due to their long response/recovery time. The way to tackle this problem is to control adsorption/desorption processes, i.e., water-vapor molecular dynamics, over the sensor's active layer through the powder and pore morphology design. With this in mind, a KIT-5-mediated synthesis was used to achieve mesoporous tin (IV) oxide replica (SnO2-R) with controlled pore size and ordering through template inversion and compared with a sol-gel synthesized powder (SnO2-SG). Unlike SnO2-SG, SnO2-R possessed a high specific surface area and quite an open pore structure, similar to the KIT-5, as observed by TEM, BET and SWAXS analyses. According to TEM, SnO2-R consisted of fine-grained globular particles and some percent of exaggerated, grown twinned crystals. The distinctive morphology of the SnO2-R-based sensor, with its specific pore structure and an increased number of oxygen-related defects associated with the powder preparation process and detected at the sensor surface by XPS analysis, contributed to excellent humidity sensing performances at room temperature, comprised of a low hysteresis error (3.7%), sensitivity of 406.8 kΩ/RH% and swift response/recovery speed (4 s/6 s).

Ultrasensitive 3D Aerosol-Jet-Printed Perovskite X-ray Photodetector.

X-ray photon detection is important for a wide range of applications. The highest demand, however, comes from medical imaging, which requires cost-effective, high-resolution detectors operating at low-photon flux, therefore stimulating the search for novel materials and new approaches. Recently, hybrid halide perovskite CH3NH3PbI3 (MAPbI3) has attracted considerable attention due to its advantageous optoelectronic properties and low fabrication costs. The presence of heavy atoms, providing a high scattering cross-section for photons, makes this material a perfect candidate for X-ray detection. Despite the already-successful demonstrations of efficiency in detection, its integration into standard microelectronics fabrication processes is still pending. Here, we demonstrate a promising method for building X-ray detector units by 3D aerosol jet printing with a record sensitivity of 2.2 × 108 µC Gyair-1 cm-2 when detecting 8 keV photons at dose rates below 1 µGy/s (detection limit 0.12 µGy/s), a 4-fold improvement on the best-in-class devices. An introduction of MAPbI3-based detection into medical imaging would significantly reduce health hazards related to the strongly ionizing X-rays' photons.

Highly Active Rutile TiO2 Nanocrystalline Photocatalysts.

The controllable synthesis of rutile TiO2 single crystal particles with the preferential orientation of {111} facets still remains a scientific and technological challenge. Here, we developed a facile route for fabrication of rutile TiO2 nanorod crystals (RTiO2NRs) having high ratios of oxidative {111} to reductive {110} surfaces. RTiO2NRs were synthesized using a peroxo-titanium complex (PTC) approach, which was controlled by changing the Ti/H2O2 ratio. The thus obtained RTiO2NRs revealed a high tendency to agglomerate through orientation-dependent attachment along the {110} facets. This resulted in an increased {111}/{110} surface ratio and led to a markedly improved photocatalytic activity of RTiO2NR aggregates. The reported findings illustrate the rich potential of the herein proposed facile and energy-efficient synthesis of nanostructured rutile TiO2-based photocatalysts.

Cefazolin-loaded polycaprolactone fibers produced via different electrospinning methods: Characterization, drug release and antibacterial effect.

Antibiotic containing polycaprolactone (PCL) fibers were produced by using three electrospinning methods: blend, emulsion and co-axial electrospinning (labeled as S1, S2 and S3, respectively). The profiles of drug release from three different systems were studied and antimicrobial properties of produced materials were evaluated. Morphology of the produced fibers was characterized and revealed that cefazolin-loaded PCL fibers had smaller diameter compared to neat PCL fibers, while the chemical interaction between the antibiotic and PCL showed that cefazolin neither had reacted with PCL phase, nor had degraded during the electrospinning process. The crystallinity and thermal characterization of fabricated fibers showed that the addition of cefazolin decreased the crystallinity of PCL. The results of the drug release behavior of the blend and co-axial electrospun fibers was on a higher level (~68% and ~43%, respectively) compared to the emulsion electrospun fibers (~5%), after a period of 30 days. The obtained data had the best fitting with the first order model and the Higuchi model, while the Korsmeyer-Peppas model showed a Pseudo-Fickian diffusion of the drug. Antibacterial evaluations showed that cefazolin-loaded PCL fibers had better effects on Staphylococcus aureus compared to Escherichia coli during the treatment period and that the effect of the emulsion fibers was notably weaker than the other two studied systems. The aim of the study was to test different systems for control drug release of different dynamics, which will be applied for prevent bacterial accumulation when indwelling urinary catheters, applied for different periods of time.

Enhanced absorption of TiO2 nanotubes by N-doping and CdS quantum dots sensitization: insight into the structure.

Anodization of titanium film sputtered on fluorine doped tin oxide (FTO) glass was performed to obtain highly ordered ∼2 µm long and ∼60 nm wide TiO2 nanotubes. The titania films were annealed in ammonia atmosphere to enable the doping with N. The annealing did not affect the nanotubular morphology and the porosity remained open which is a very important requirement for further deposition of CdS quantum dots. The analysis done by transmission electron microscopy (TEM) has shown that the N-doped nanotubes have a smaller interplanar distance as compared to the undoped ones, whose interplanar distance corresponded to anatase phase. This difference was attributed to the N doping and the Sn migration from the substrate, as demonstrated by energy dispersive spectroscopy (EDS) combined with electron energy loss spectroscopy (EELS). The near edge X-ray absorption fine structure (NEXAFS) analysis clearly demonstrated that also the doped TiO2 film has anatase phase. Regarding the chemical composition of the studied samples, the X-ray photoelectron spectroscopy (XPS) and synchrotron radiation photoelectron spectroscopy (SRPES) analyses have shown that N is incorporated both interstitially and substitutionally in the TiO2 lattice, with a decreased contribution of the interstitial after ionic sputtering. The shift of the valence band maximum (VBM) position for the doped TiO2 vs. the undoped TiO2 proved the narrowing of the band gap. The CdS/TiO2 films show bigger VBM shifting that can be attributed to CdS deposit. Comparing the absorption spectra of the bare undoped and doped TiO2 samples, it was noticed that the doping causes a red shift from 397 to 465 nm. Furthermore, the CdS deposition additionally enhances the absorption in the visible range (575 nm for undoped TiO2/CdS and 560 nm for doped TiO2/CdS films).

Novel modified nanocellulose applicable as reinforcement in high-performance nanocomposites.

The influence of modification and vacuum/supercritical CO2 (scCO2) drying methods on the surface properties, morphology and thermal stability of cellulose nanocrystals (NC) was presented in this study. Introduction of reactive vinyl groups on NC surface was performed by either direct esterification with oleic acid, linseed or sunflower oil fatty acids; or by amidation of maleic acid/ethylene diamine with methyl ester of fatty acid. Obtained modified NC (m-NC) were characterized using FTIR and Raman spectroscopy; and by determination of acid, iodine and ester values. Structural analysis of m-NC showed varieties of forms, from spongy to nanostructural non-uniform layered morphology with observable agglomeration, which confirmed morphology dependence on modification/processing methods Thermogravimetry-MS spectrometry showed different thermal stability and degradation pathways of NC/m-NC. Incorporation of 1 wt% of reactive m-NC in unsaturated polyester lead to high performance nanocomposites and contributed to increase of stress at break in the range from 76 to 93%.

Immobilization of horseradish peroxidase onto kaolin.

Kaolin showed as a very perspective carrier for the enzyme immobilization and it was used for the adsorption of horseradish peroxidase (HRP). The effects of the enzyme concentration and pH on the immobilization efficiency were studied in the reaction with pyrogallol and anthraquinone dye C.I. Acid Violet 109 (AV 109). In addition, Fourier transform infrared spectroscopy, scanning electron microscopy and analysis by Brunauer-Emmett-Teller were performed for kaolin, thermally activated kaolin and the immobilized enzyme. It has been shown that 0.1 IU of HRP-kaolin decolorized 87 % of dye solution, under the optimal conditions (pH 5.0, temperature 24 °C, dye concentration 40 mg/L and 0.2 mM of H2O2) within 40 min. The immobilized HRP decolorization follows the Ping Pong Bi-Bi mechanism with dead-end inhibition by the dye. The biocatalyst retained 35 ± 0.9 % of the initial activity after seven cycles of reuse in the decolorization reaction of AV 109 under optimal conditions in a batch reactor. The obtained kinetic parameters and reusability study confirmed improvement in performances of k-HRP compared to free, indicating that k-HRP has a great potential for environmental purposes.