Producers of Engineered Nanomaterials-What Motivates Company and Worker Participation in Biomonitoring Programs?

Production and handling of engineered nanomaterials (ENMs) can yield worker exposure to these materials with the potential for unforeseen negative health effects. Biomonitoring enables regular exposure and health assessment and an effective risk management. We aimed to identify factors influencing biomonitoring acceptance according to hierarchical positions of ENM producers. Managers and workers were invited to complete an online questionnaire. Forty-three companies producing or handling ENMs such as titanium dioxide (61%) and multi-walled carbon nanotubes (44%) participated. The majority of managers (72%) and all workers responded positively to participating in biomonitoring studies. The main reasons for refusing participation included concerns about data confidentiality and sufficient knowledge about ENM health and safety. Acquisitions of individual study results, improvement of workers' safety, and help to the development of ENM-specific health and safety practice were among the most valuable reasons for positively considering participation. All workers indicated feeling comfortable with biomonitoring procedures of exhaled air sampling-about half were similarly comfortable with exhaled breath condensate, urine, and buccal cell sampling. The majority of both workers and managers stated that participation in a biomonitoring program should take place during working hours. Although our survey only had limited participation, our results are useful in designing appropriate biomonitoring programs for workers exposed to ENMs.

Indoor dispersion of airborne nano and fine particles: Main factors affecting spatial and temporal distribution in the frame of exposure modeling.

A particle exposure experiment inside a large climate-controlled chamber was conducted. Data on spatial and temporal distribution of nanoscale and fine aerosols in the range of mobility diameters 8-600 nm were collected with high resolution, for sodium chloride, fluorescein sodium, and silica particles. Exposure scenarios studied included constant and intermittent source emissions, different aggregation conditions, high (10 h-1 ) and low (3.5 h-1 ) air exchange rates (AERs) corresponding to chamber Reynolds number, respectively, equal to 1 × 105 and 3 × 104 . Results are presented and analyzed to highlight the main determinants of exposure and to determine whether the assumptions underlying two-box models hold under various scenarios. The main determinants of exposure found were the source generation rate and the ventilation rate. The effect of particles nature was indiscernible, and the decrease of airborne total number concentrations attributable to surface deposition was estimated lower than 2% when the source was active. A near-field/far-field structure of aerosol concentration was always observed for the AER = 10 h-1 but for AER = 3.5 h-1 , a single-field structure was found. The particle size distribution was always homogeneous in space but a general shift of particle diameter (-8% to +16%) was observed between scenarios in correlation with the AER and with the source position, presumably largely attributable to aggregation.

Novel techniques for detection and characterization of nanomaterials based on aerosol science supporting environmental applications.

The number of people exposed to nanoparticles is growing accordingly to the production and development of new nanomaterials. Moreover, this increase is expected to continue in the future. However, there is a lack of standardized sampling and metric methods to measure the level of exposure to nanoparticles, and the information related to possible adverse health effects is scarce. Aerosol technology has been detecting and characterizing nanoparticles for decades and some of their developments can be of use in nanotechnology characterization. We present here two current developments based on used principles in aerosol science, which can widen its application to the characterization of nanomaterials. On the one hand, a sample preparation technique for nanoparticle analysis by electron microscopy based on electrospray atomization technology. Several samples prepared in this way have been analysed and compared to more traditional sample preparation strategies like the "drop on grid" method. It was found that the particles deposited by electrospray generally show a much more homogeneous spatial distribution on the substrate and the number of single particles increases substantially. On the other hand, it is presented an electrical mobility classification system, DMA, with enormous possibilities for the quick and economic size characterization of suspensions of nanoparticles, thanks to its injection system by electrospray and to its high resolution in the lower range of the nanoscale. The first assessment of the abovementioned devices highlights its potential applications in exposure assessment and nanotechnological contexts.