Bone tissue engineering techniques, advances and scaffolds for treatment of bone defects.

Bone tissue engineering (BTE) aims to develop strategies to regenerate damaged or diseased bone using a combination of cells, growth factors, and biomaterials. This article highlights recent advances in BTE, with particular emphasis on the role of the biomaterials as scaffolding material to heal bone defects. Studies encompass the utilization of bioceramics, composites, and myriad hydrogels that have been fashioned by injection molding, electrospinning, and 3D bioprinting over recent years, with the aim to provide an insight into the progress of BTE along with a commentary on their scope and possibilities to aid future research. The biocompatibility and structural efficacy of some of these biomaterials are also discussed.

Radiofrequency ablation of the centromedian thalamic nucleus in the treatment of drug-resistant epilepsy.

OBJECTIVE: To determine the usefulness and efficacy of radiofrequency ablations (RFA) of the Centromedian thalamic nucleus (CMN) to control primarily generalized or multifocal seizures in refractory epilepsy. METHODS: Six patients with clinical diagnosis of multifocal or primarily generalized drug-resistant epilepsy were included. Bilateral RFA of the CMN was performed through a monopolar 1.8 mm. tip electrode with a temperature of 80 °C during 90 seconds. Patients were followed in every 3 months visit for 20 to 36 months and kept a monthly seizure count calendar. We also compared maximal paroxysmal electroencephalogram (EEG) activity and neuropsychological evaluation pre and 6 months postoperatively. RESULTS: A significant reduction in the number of generalized seizures was observed in all subjects in the range of 79-98%, starting the first post-operative month. Although focal aware seizures remained unchanged throughout follow-up, there was an important reduction on paroxysmal activity between the pre and postoperative EEG. No major changes on cognitive status were detected. There was post-operative dysphagia and odynophagia lasting one week and there was no mortality in this group of patients. CONCLUSION: Preliminary results of CMN RFA suggest safety and a trend toward reduction of some seizure types, it may reduce the seizure frequency like other palliative procedures since the first post-operative month, but a larger, controlled study would be needed to establish the value of this therapy.

A Comparative Study in the Printability of a Bioink and 3D Models Across Two Bioprinting Platforms.

In this study, we used an alginate-gelatin bioink to design and print 3D constructs with lattice, honeycomb and fibrous bundle patterns. These designs were printed using a small-scale laboratory printer, at first and later translated to a larger scale, high throughput-printing platform. A comparative analysis of the structures printed using two dissimilar platforms using gross morphologic evaluation, scanning electron microscopy and swelling assay confirmed our hypothesis that a design printed using a small-scale laboratory bioprinter for optimization of bioink composition and printing parameters can be successfully translated into a large scale-printing platform for high throughput printing of constructs. Since the designs for printing were implemented using a software which was common across both printers, this endpoint was feasible. The only difference in printing parameters resulted from variation in extrusion pressure which was due to a significant difference in barrel size used across both printers (3 ml versus 30 ml), while all other parameters stayed the same. Although the scaffolds were not bioprinted with cells, in future we will investigate how cell viability can be differentially regulated by the variation of extrusion pressure across both platforms.

A Comparative Study of a 3D Bioprinted Gelatin-Based Lattice and Rectangular-Sheet Structures.

3D bioprinting holds great promise in the field of regenerative medicine as it can create complex structures in a layer-by-layer manner using cell-laden bioinks, making it possible to imitate native tissues. Current bioinks lack both high printability and biocompatibility required in this respect. Hence, the development of bioinks that exhibit both properties is needed. In our previous study, a furfuryl-gelatin-based bioink, crosslinkable by visible light, was used for creating mouse mesenchymal stem cell-laden structures with a high fidelity. In this study, lattice mesh geometries were printed in a comparative study to test against the properties of a traditional rectangular-sheet. After 3D printing and crosslinking, both structures were analysed for swelling and rheological properties, and their porosity was estimated using scanning electron microscopy. The results showed that the lattice structure was relatively more porous with enhanced rheological properties and exhibited a lower degradation rate compared to the rectangular-sheet. Further, the lattice allowed cells to proliferate to a greater extent compared to the rectangular-sheet, which initially retained a lower number of cells. All of these results collectively affirmed that the lattice poses as a superior scaffold design for tissue engineering applications.

Effect of 2,6-Bis-(1-hydroxy-1,1-diphenyl-methyl) Pyridine as Organic Additive in Sulfide NiMoP/γ-Al2O3 Catalyst for Hydrodesulfurization of Straight-Run Gas Oil.

The effect of 2,6-bis-(1-hydroxy-1,1-diphenyl-methyl) pyridine (BDPHP) in the preparation of NiMoP/γ-Al2O3 catalysts have been investigated in the hydrodesulfurization (HDS) of straight-run gas oil. The γ-Al2O3 support was modified by surface impregnation of a solution of BDPHP to afford BDPHP/Ni molar ratios (0.5 and 1.0) in the final composition. The highest activity for NiMoP materials was found when the molar ratio of BDPHP/Ni was of 0.5. X-ray diffraction (XRD) results revealed that NiMoP (0.5) showed better dispersion of MoO3 than the NiMoP (1.0). Fourier transform infrared spectroscopy (FT-IR) results indicated that the organic additive interacts with the γ-Al2O3 surface and therefore discards the presence of Mo or Ni complexes. Raman spectroscopy suggested a high Raman ratio for the NiMoP (0.5) sample. The increment of the Mo=O species is related to a major availability of Mo species in the formation of MoS2. The temperature programmed reduction (TPR) results showed that the NiMoP (0.5) displayed moderate metal-support interaction. Likewise, X-ray photoelectron spectroscopy (XPS) exhibited higher sulfurization degree for NiMoP (0.5) compared with NiMoP (1.0). The increment of the MoO3 dispersion, the moderate metal-support interaction, the increase of sulfurization degree and the increment of Mo=O species provoked by the BDPHP incorporation resulted in a higher gas oil HDS activity.