Load-bearing capacity under fatigue of bonded-yttria tetragonal zirconia polycrystals and -yttria-stabilized zirconia: Effects of the viscosity of a dual-cured resin cement.

This study aimed to evaluate the effect of low and high viscosities of dual-cured resin cement on the mechanical fatigue behavior of yttria tetragonal zirconia polycrystals (3Y-TZP) and yttria-stabilized zirconia (4YSZ) adhesively luted to a dentin analogue (glass fiber-reinforced epoxy resin). Ceramic discs were randomly divided into four groups (n = 20) based on the following study factors: dual-cured resin cement viscosities (low and high) and zirconia microstructure (3Y-TZP and 4YSZ). The discs were treated by air abrasion with aluminum oxide particles (50 µm), followed by the application of primer, and then luted with high or low viscosity resin cement to the dentin analogue. Subsequently, the luted sets underwent a step-stress fatigue test, which involved an initial load of 200 N, step increments of 100 N, 10,000 cycles per step, and a frequency of 20 Hz. Data on fatigue failure load (FFL) and the number of cycles for failure (CFF) were collected and analyzed using survival tests, including Kaplan-Meier and Mantel-Cox analyses, as well as Weibull analysis. Additionally, topography analysis, fractographic features, bonding interface analysis, and Raman spectroscopy were performed. The results revealed that 3Y-TZP exhibited superior fatigue behavior compared to 4YSZ, regardless of the viscosity of the resin cement used for luting. Among all groups, 3Y-Low exhibited the best fatigue performance, while 4YSZ luted with low or high viscosity resin cements yielded the lowest fatigue behavior (FFL). There were no significant differences in Weibull modulus among the groups. After air abrasion, both ceramics showed similar topography. Raman analysis indicated that the surface of 3Y-TZP ceramics prior to sintering had a monoclinic phase, which transitioned predominantly to tetragonal phase peaks after sintering. A similar transition was observed in 4YSZ ceramics. In summary, 3Y-TZP exhibited superior mechanical fatigue behavior compared to 4YSZ. The influence of resin cement viscosity on fatigue behavior was more pronounced in 3Y-TZP, with low-viscosity resin cement enhancing its performance. However, the mechanical fatigue behavior of 4YSZ was less affected by the viscosity of the dual-cured resin cement, showing similar results with both low and high viscosities. In conclusion, 3Y-TZP demonstrated superior mechanical fatigue behavior compared to 4YSZ. The impact of resin cement viscosity on fatigue behavior was more pronounced in 3Y-TZP, with low-viscosity resin cement enhancing its performance. Conversely, the mechanical fatigue behavior of 4YSZ was less sensitive to the viscosity of the dual-cured resin cement, resulting in similar outcomes with both low and high viscosities.

SOD activity of new copper II complexes with ligands derived from pyridoxal and toxicity in Caenorhabditis elegans.

This work presents the synthesis, characterization of copper(II) complexes (C1-C6) and the potential of these compounds to mimic the catalytic activity of the enzyme superoxide dismutase (SOD). The copper(II)complexes were obtained by reaction between the aldol condensation between substituted aromatic hydrazides and aromatic aldehydes (salicylic aldehyde and pyridoxal hydrochloride), forming two new ligands (L1 to L6), resulting in new dimeric dicopper (II) complexes (C1 and C2), new three monomeric CuII derivatives (C3, C4 and C6) and a polymeric complex (C5). The CuII complexes were fully characterized by X-ray diffraction, spectroscopic and electrochemical analysis. Subsequently, CuII derivatives were evaluated for their antioxidant activities, using the NBT (Nitro blue tetrazolium chloride) photoreduction methodology. After evaluating the antioxidant activity in vitro, it was observed that the best inhibition rates of the superoxide ion are associated to the C4 and C5 complexes. Computational analysis via molecular docking and quantum chemical calculation (Fukui map) offered a molecular level explanation on the biological activity of CuII complexes. Additionally, cytotoxicity of C1-C6 was tested in the first time in vivo in nematodes Caenorhabditis elegans, corroborating with the results identified for C4 and C5.

Multi-technique investigation of potshards of a cerrito (earthen mound) from southern Brazil.

The physicochemical investigation of ceramics crafted and managed by ancient humans allows a better understanding of their social, technological, economical, routine and artistic activities. The Brazilian State of Rio Grande do Sul presents the biggest number of registered archaeological sites in the country, and many of them are earthen mounds, locally known as cerritos de indios. This kind of archaeological site is of utmost importance to understand the social development of the biome Pampa - including areas from Brazil, Argentina and Uruguay - and almost nothing is known about the physicochemical composition of the artifacts from the Brazilian portion. In this work we investigated the mineral phases present in archaeological ceramics from the cerrito Pavão I (PSG-20) by means of white light microscopy (petrography), Raman micro-spectroscopy, XRD and XRF spectroscopies, and FTIR-ATR. Different minerals were identified and allowed to propose a firing temperature of ca. 500-650 °C. It was also suggested that the makers used both oxidizing and reducing atmospheres, that more than one clay source was used to prepare the ceramics, and that trace elements are present in different shards. Regarding the multi-analytical technique approach, the results highlight the importance of complementary investigations and underline the role of Raman micro-spectroscopy for these objects.

Endodontic Sealers Affect the Bond Strength of Fiber Posts and the Degree of Conversion of Two Resin Cements.

PURPOSE: To evaluate the effect of two endodontic sealers on the push-out bond strength between fiber posts and root canal wall after different storage times and verify the influence of the endodontic sealers on the degree of conversion of composite cements. MATERIALS AND METHODS: A total of 180 bovine teeth were endodontically treated using two endodontic sealers, eugenol-based (Endofill, Dentsply Maillefer) or epoxy resin-based (AH Plus, Dentsply Maillefer). Subsequently, the specimens were stored in 100% relative humidity at 37°C for 24 h, 6 or 12 months. After the respective storage times, the root canals were prepared for fiber post cementation using two composite cements, RelyX U200 (3M) or Multilink Automix (Ivoclar Vivadent). The push-out test and the failure analysis were performed. Degree of conversion was analyzed using a Raman microscope, for which samples were prepared using composite cement only or composite cement plus endodontic sealer. Finally, the push-out data were subjected to statistical analysis and the degree of conversion in percent was calculated. RESULTS: AH Plus sealer obtained the highest push-out bond strengths at 24 h and 6 months. There was no difference between the push-out bond strengths of AH Plus and Endofill sealer at 1 year (p < 0.05). Moreover, the degree of conversion was affected by the Endofill sealer. CONCLUSION: The use of a eugenol-based sealer is not recommended because it affects the push-out bond strength of fiber posts. AH Plus sealer and a post-endodontic waiting time of 24 h is recommended.