Investigation of the main factor affecting the NOx distribution in the street canyon with the photo-catalytic wall.

To find out the most contaminated street region and protect the pedestrian with the photo-catalytic equipment to decrease the hazard of oxynitride (NOx), Computational Fluid Dynamics (CFD) simulation could be used to research the main factor affecting the statistical characteristics of the oxynitride distribution in the urban street canyon with the photo-catalytic building walls. Additionally, the connection was investigated and focused on the swirling flow and oxynitride concentration to find out the root of the main factor affecting oxynitride distribution. The simulation results showed that there was one three-dimensional swirling flow in the whole canyon and the statistical concentration was straightforwardly related to the swirling or whirling flow structure (such as eddy). The characteristics had been confirmed that the whirling flow structure affected the complex oxynitride distribution in the street canyon with the photo-catalytic building walls. Furthermore, one formula was found which described the oxynitride concentration constrained by the street canyon. This study illustrated that different sections in the canyon had various patterns of the whirling flow structure (swirling flow) and oxynitride. In the symmetrical portion of the street canyon (in the middle of the street length), there is one concise equation to describe the NOx concentration affected by the turbulence intensity. Moreover, the equation was presented as CR = 1.094 + 0.11e-I, where I was the turbulence intensity and CR was the oxynitride relative concentration in the street canyon.

Catalytic Degradation of Lignin over Sulfonyl-Chloride-Modified Lignin-Based Porous Carbon-Supported Metal Phthalocyanine: Effect of Catalyst Concentrations.

A sulfonyl-chloride-modified lignin-based porous carbon-supported metal phthalocyanine catalyst was prepared and used to replace the traditional Fenton's reagent for lignin degradation. The catalyst underwent a detailed characterization analysis in terms of functional group distributions, surface area, morphological structure, via FT-IR, XPS, BET, and SEM. The catalyst possessed a specific surface area of 638.98 m2/g and a pore volume of 0.291 cm3/g. The prepared catalyst was studied for its ability of oxidative degradation of lignin under different reaction conditions. By optimizing the reaction conditions, a maximum liquid product yield of 38.94% was obtained at 135 °C with 3.5 wt% of catalyst and 15 × 10-2 mol/L H2O2; at the same time, a maximum phenols selectivity of 32.58% was achieved. The compositions and properties of liquid products obtained from lignin degradation using different catalyst concentrations were studied comparatively via GC-MS, FT-IR, 1H-NMR, and EA. Furthermore, the structure changes of solid residues are also discussed.

Fabrication and Characterization of Graphene Microcrystal Prepared from Lignin Refined from Sugarcane Bagasse.

Graphene microcrystal (GMC) is a type of glassy carbon fabricated from lignin, in which the microcrystals of graphene are chemically bonded by sp³ carbon atoms, forming a glass-like microcrystal structure. The lignin is refined from sugarcane bagasse using an ethanol-based organosolv technique which is used for the fabrication of GMC by two technical schemes: The pyrolysis reaction of lignin in a tubular furnace at atmospheric pressure; and the hydrothermal carbonization (HTC) of lignin at lower temperature, followed by pyrolysis at higher temperature. The existence of graphene nanofragments in GMC is proven by Raman spectra and XRD patterns; the ratio of sp² carbon atoms to sp³ carbon atoms is demonstrated by XPS spectra; and the microcrystal structure is observed in the high-resolution transmission electron microscope (HRTEM) images. Temperature and pressure have an important impact on the quality of GMC samples. With the elevation of temperature, the fraction of carbon increases, while the fraction of oxygen decreases, and the ratio of sp² to sp³ carbon atoms increases. In contrast to the pyrolysis techniques, the HTC technique needs lower temperatures because of the high vapor pressure of water. In general, with the help of biorefinery, the biomass material, lignin, is found to be qualified and sustainable material for the manufacture of GMC. Lignin acts as a renewable substitute for the traditional raw materials of glassy carbon, copolymer resins of phenol formaldehyde, and furfuryl alcohol-phenol.

A comparative study for the organic byproducts from hydrothermal carbonizations of sugarcane bagasse and its bio-refined components cellulose and lignin.

Sugarcane bagasse was refined into cellulose, hemicellulose, and lignin using an ethanol-based organosolv technique. The hydrothermal carbonization (HTC) reactions were applied for bagasse and its two components cellulose and lignin. Based on GC-MS analysis, 32 (13+19) organic byproducts were derived from cellulose and lignin, more than the 22 byproducts from bagasse. Particularly, more valuable catechol products were obtained from lignin with 56.8% share in the total GC-MS integral area, much higher than the 2.263% share in the GC-MS integral areas of bagasse. The organic byproducts from lignin make up more than half of the total mass of lignin, indicating that lignin is a chemical treasure storage. In general, bio-refinery and HTC are two effective techniques for the valorization of bagasse and other biomass materials from agriculture and forest industry. HTC could convert the inferior biomass to superior biofuel with higher energy quantity of combustion, at the same time many valuable organic byproducts are produced. Bio-refinery could promote the HTC reaction of biomass more effective. With the help of bio-refinery and HTC, bagasse and other biomass materials are not only the sustainable energy resource, but also the renewable and environment friendly chemical materials, the best alternatives for petroleum, coal and natural gas.

A new type of two-dimensional carbon crystal prepared from 1,3,5-trihydroxybenzene.

A new two-dimensional (2D) carbon crystal, different from graphene, has been prepared from 1,3,5-trihydroxybenzene, consisting of 4-carbon and 6-carbon rings in 1:1 ratio, named 4-6 carbophene by authors, in which all carbon atoms possess sp2 hybrid orbitals with some distortion, forming an extensive conjugated π-bonding planar structure. The angles between the three σ-bonds of the carbon sp2 orbitals are roughly 120°, 90°, and 150°. Each of the three non-adjacent sides of a 6C-ring is shared with a 4C-ring; and each of the two opposite sides of a 4C-ring is shared with a 6C-ring. Dodecagonal holes with a diameter of approximate 5.8 Å are regularly located throughout the 2D carbon crystal. Even though the bond energies in 4-6 carbophene are weaker than those in the graphene, the new planar crystal is quite stable in ambient conditions. The 4-6 carbophene can be synthetized from 1,3,5-trihydroxybenzene or other benzene derivatives through dehydration and polymerization reactions, and may possess several possible patterns that form a family of 2D carbon crystals. A possible side reaction involving 1,3,5-trihydroxybenzene is also discussed, which may produce a carbon-oxygen two dimensional crystal.