Effects of hydrogen peroxide cleaning procedures on bone graft osteoinductivity and mechanical properties.

Bone allografts are frequently used during orthopaedic trauma cases or other reconstructive procedures. Most allografts are processed and cleaned before use. Our goals were to determine if an improved cleaning procedure compromises the strength or osteoinductivity of a graft. We compared our improved cleaning procedure to our standard cleaning procedure on cortical bone allograft. The cleaning procedures are generally composed of a series of chemical steps with nonionic detergents, hydrogen peroxide, and alcohol under time and temperature control, subjected to ultrasonic agitation. We tested the compressive strength, impact strength, and shear strength following the standard and improved cleaning procedures. Osteoinductivity was tested in 4 groups, using the improved cleaning procedure with four different hydrogen peroxide cleaning times: 0, 1, 3, and 5 h. Osteoinductivity was evaluated in vivo, using a 28-day implant in the hamstring muscle of an athymic, nude mouse. Results demonstrated that osteoinductivity is maintained with cleaning in hydrogen peroxide for up to 1 h, and that compressive strength, impact strength, and shear strength were all unaffected by the improved cleaning procedure. The improved cleaning procedure therefore did not compromise the strength or osteoinductivity of cortical bone allografts in comparison to the standard procedure.

Energy restriction reduces bone density and biomechanical properties in aged female rats.

Bone mineral density (BMD) is highly correlated with body weight, and weight loss is associated with reduced BMD. Whether such losses of BMD increase skeletal fragility is unclear. We examined the effect of 9 wk of energy restriction (ER) on bone density, mineral and matrix protein composition and biomechanical properties in mature (20 wk old, n = 12) and aged (48 wk old, n = 16) female rats. Energy-restricted rats were fed 40% less energy than controls that consumed food ad libitum. Bone content of mineral (ash and calcium content) and matrix proteins (hydroxyproline, pyridinium crosslinks and proteoglycans), serum hormones, site-specific bone density and biomechanical properties (peak load, peak torque, shear stiffness and bending stiffness) were measured at the conclusion of the study. In both age groups, ER reduced body weight by 15 +/- 10% (P < 0.001) and dramatically decreased femoral bone density by 32-35% (P < 0.01) compared with controls. Energy restriction resulted in a small reduction in tibia and humerus density, as well as biomechanical properties in the aged but not mature rats (P < 0.05). Reduced serum levels of insulin and estradiol due to ER in aged rats (P < 0.05) may play a role in altering bone quality. These data show that although weight loss due to ER is detrimental to some bone parameters in mature rats, only aged rats show consistent reductions in bone density and biomechanical properties.

Impact of parental substance use disorder and child neglect severity on substance use involvement in male offspring.

Two child self-report scales were developed to measure parental neglect (emotional distance and parental involvement) in a sample of 344 boys between 10 and 12 years of age. Psychometric analyses of the parental emotional distance and involvement scales demonstrated their unidimensionality; construct, concurrent, and predictive validity; and reliability. Cross-sectional analyses indicated that neglect was more severe among boys who had a parent with a DSM-III-R lifetime substance use disorder (SUD) compared to youth whose parents had no Axis I psychiatric disorder. In addition, children reported more severe neglect by the mother than the father. Longitudinal analyses of a subsample (n = 99) revealed that child neglect at ages 10-12 predicted significant variance on a composite measure of substance use involvement and severity of substance use as well as increased the risk for SUD at age 19.

Evaluation of single nucleotide polymorphism typing with invader on PCR amplicons and its automation.

Large-scale pharmacogenetics and complex disease association studies will require typing of thousands of single-nucleotide polymorphisms (SNPs) in thousands of individuals. Such projects would benefit from a genotyping system with accuracy >99% and a failure rate <5% on a simple, reliable, and flexible platform. However, such a system is not yet available for routine laboratory use. We have evaluated a modification of the previously reported Invader SNP-typing chemistry for use in a genotyping laboratory and tested its automation. The Invader technology uses a Flap Endonuclease for allele discrimination and a universal fluorescence resonance energy transfer (FRET) reporter system. Three hundred and eighty-four individuals were genotyped across a panel of 36 SNPs and one insertion/deletion polymorphism with Invader assays using PCR product as template, a total of 14,208 genotypes. An average failure rate of 2.3% was recorded, mostly associated with PCR failure, and the typing was 99.2% accurate when compared with genotypes generated with established techniques. An average signal-to-noise ratio (9:1) was obtained. The high degree of discrimination for single base changes, coupled with homogeneous format, has allowed us to deploy liquid handling robots in a 384-well microtitre plate format and an automated end-point capture of fluorescent signal. Simple semiautomated data interpretation allows the generation of approximately 25,000 genotypes per person per week, which is 10-fold greater than gel-based SNP typing and microsatellite typing in our laboratory. Savings on labor costs are considerable. We conclude that Invader chemistry using PCR products as template represents a useful technology for typing large numbers of SNPs rapidly and efficiently.

Effect of chemical treatments on tendon cellularity and mechanical properties.

Removal of cells may decrease the antigenicity and risk of disease transmission associated with tendon allografts and xenografts. An ideal cell removal method would not compromise graft structure and mechanical properties. This study compared the effects of three extraction chemicals [t-octyl-phenoxypolyethoxyethanol (Triton X-100), tri(n-butyl)phosphate (TnBP), and sodium dodecyl sulfate (SDS)] on tendon cellularity, structure, nativity, and mechanical properties. Rat tail tendons were soaked in extraction solutions for various time periods (12-48 h) and concentrations (0.5-2%), then they were rinsed with distilled water and ethyl alcohol. Histological analysis and tensile tests were performed on control and chemically treated tendons. Changes in collagen nativity were estimated by mechanical testing following incubation in a trypsin solution. Treatment of tendons with 1% Triton X-100 for 24 h disrupted the collagen fiber structure and did not remove cells. Treatment with 1% SDS for 24 h or 1% TnBP for 48 h resulted in an acellular tendon matrix with retention of near normal structure and mechanical properties. Consistent with previous studies demonstrating cell removal from other tissue types using SDS and TnBP, our preliminary results suggest these treatments are potentially useful for removing cells from tendon allografts or xenografts without compromising the graft structure or mechanical properties.

Heme oxygenase-1 gene expression as a stress index to ocular irritation.

PURPOSE: Predicting the toxic potential of compounds to the ocular surface has depended on the Draize test for the past half century. Alternatives to Draize testing have recently been sought for a number of reasons. Stress gene expression has emerged as a means of quantifying cellular reaction and, thus, the toxic potential of the compound in question. This study examines the expression of the major stress response gene heme oxygenase-1 (HO-1) in a human corneal epithelial cell line (HCE-T) following challenges with a number of known ocular irritants. METHODS: HCE-T was used to investigate the effect of ocular irritants on cell viability and HO-1 expression. Irritants tested included hydrogen peroxide, isopropyl alcohol, sodium hydroxide and trichloroacetic acid. HCE-T cells were grown to 80% confluency and treated with the listed irritants at a concentration range of 10-100 microM. Cell viability and northern blot analysis were performed following a 24 and 48 hr incubation period. RESULTS: HCE-T cells expressed HO-1 mRNA and HO activity similar to other human cell lines. Northern blot analysis demonstrated that levels of HO-1 mRNA transcripts increased regularly after exposure to the irritants in a concentration-dependent manner. Studies on the effect of various inhibitors and inducers of HO-1 on cell viability showed that inhibition of HO-1 potentiates the cytotoxic effect of ocular irritants. In contrast, pre-induction of HO-1 in HCE-T decreases the effect of various irritants on cell viability. CONCLUSIONS: These results are consistent with the idea that HO-1 mRNA levels may be used as an indicator of toxicity resulting from ocular irritants and that HCE-T cells respond to stress in a fashion similar to other human cell lines. This strategy for testing may be important in the development of an alternative to Draize testing. The results of this study also suggest that HO-1 may constitute a part of the protective defense mechanism against chemical injury.

Viability of fibroblast-seeded ligament analogs after autogenous implantation.

Fibroblast-seeded collagen scaffolds or ligament analogs are potentially useful for reconstruction of the anterior cruciate ligament of the knee. To provide lasting benefits, the seeded cells must survive implantation within the harsh synovial environment of the knee joint. Our objective was to determine the in vivo fate of autogenous fibroblast-seeded ligament analogs as a function of fibroblast source (anterior cruciate ligament or skin), implantation site (knee joint or subcutaneous space), and time after implantation (1, 2, 4, 6, or 8 weeks). Before implantation, fibroblasts were labeled with PKH26-GL, a fluorescent membrane dye. Immediately after retrieval of the implant, the viability of the labeled seeded cells was assessed under a fluorescent microscope. Viable seeded fibroblasts remained attached to the collagen fibers within the ligament analogs for at least 4 weeks (skin fibroblasts) or 6 weeks (anterior cruciate ligament fibroblasts) after implantation. A larger number of viable seeded cells were consistently observed in the subcutaneous space than in the knee joint. Scaffold resorption prevented observation at the 8-week time period. Fibroblast-seeded ligament analogs remained viable for prolonged periods in the knee joint and therefore have the potential to influence the formation and remodeling of neoligament tissue after reconstruction of the anterior cruciate ligament.

A search for type 1 diabetes susceptibility genes in families from the United Kingdom.

Genetic analysis of a mouse model of major histocompatability complex (MHC)-associated autoimmune type 1 (insulin-dependent) diabetes mellitus (IDDM) has shown that the disease is caused by a combination of a major effect at the MHC and at least ten other susceptibility loci elsewhere in the genome. A genome-wide scan of 93 affected sibpair families (ASP) from the UK (UK93) indicated a similar genetic basis for human type 1 diabetes, with the major genetic component at the MHC locus (IDDM1) explaining 34% of the familial clustering of the disease (lambda(s)=2.5; refs 3,4). In the present report, we have analysed a further 263 multiplex families from the same population (UK263) to provide a total UK data set of 356 ASP families (UK356). Only four regions of the genome outside IDDM1/MHC, which was still the only major locus detected, were not excluded at lambda(s)=3 and lod=-2, of which two showed evidence of linkage: chromosome 10p13-p11 (maximum lod score (MLS)=4.7, P=3x10(-6), lambda(s)=1.56) and chromosome 16q22-16q24 (MLS=3.4, P=6.5x10(-5), lambda(s)=1.6). These and other novel regions, including chromosome 14q12-q21 and chromosome 19p13-19q13, could potentially harbour disease loci but confirmation and fine mapping cannot be pursued effectively using conventional linkage analysis. Instead, more powerful linkage disequilibrium-based and haplotype mapping approaches must be used; such data is already emerging for several type 1 diabetes loci detected initially by linkage.

Bone geometry and strength measurements in aging mice with the oim mutation.

Mice with the naturally occurring oim mutation allows investigation of bone pathobiology in the setting of one mutation: a G deletion in the murine Cola-2 gene (exon 52) encoding the proalpha2(I) C-propeptide. As a result, normal sized mRNA is transcribed, but no secreted protein has been identified in oim/oim fibroblasts or osteoblasts. Here we report longitudinal changes in body mass, bone geometry, and bone structural properties of femurs tested in torsion from wild type (+/+) mice and mice homozygous (oim/oim) and heterozygous (+/oim) for the oim mutation. Femurs from mice 3 months, 6 months, 12 months, and >18 months of age were dissected and X-ray films were taken in anterioposterior and mediolateral views to estimate the geometric properties. The metaphyseal ends of femurs were potted in polymethylemethacrylate and mounted on a torsional test fixture designed to convert axial tensile deformation to a torsional load using an INSTRON model 4204 materials tester. Compared with +/+ samples, peak torque at failure was reduced in oim/oim mice. Also, the geometric distribution of midshaft bone for oim/oim mice in terms of cortical area and polar moment was significantly reduced. However, the impact of the mutation on bone distribution was relatively minor for +/oim mice. Consistent with a type III classification in human OI patients, the presence of two nonfunctional alleles in homozygous oim mice significantly reduced body mass compared with age-matched wild type mice. However, no statistical difference in body mass was detected between +/oim and +/+ mice. The absence of a gross phenotypic difference between +/oim and +/+ mice demonstrates a milder phenotype in +/oim mice.

Identification of two sequence elements associated with the gene encoding the 24-kDa crystalline component in Bacillus thuringiensis ssp. fukuokaensis: an example of transposable element archaeology.

A 6.5-kb fragment of plasmid DNA from Bacillus thuringiensis (Bt) ssp. fukuokaensis that encodes a 24-kDa crystalline component was analyzed to identify additional open reading frames (orfs). A novel Bt IS240-like element was found upstream of this gene and is considered to be a vestige of a once active insertion sequence due to a stop codon that interrupts the long orf encoding the putative transposase. This element was bounded by 17-bp terminal inverted repeats that defined the length of the insertion sequence as 802 bp. Further upstream of this element two tandem overlapping and out of phase open reading frames (orfX and orfY) were identified which represent the first example of an IS150-like element in Bt containing both orfs. orfX and orfY are not bounded by terminal inverted repeats but are associated with a gene encoding a putative site-specific recombinase of a type found in Staphylococcus aureus Class II transposons but not previously in Bt.

Effect of physical crosslinking methods on collagen-fiber durability in proteolytic solutions.

We previously demonstrated that ultraviolet (UV) or dehydrothermal (DHT) crosslinking partially denatured fibers extruded from an insoluble type I collagen dispersion. In this study denaturation effects were evaluated by measuring collagen-fiber sensitivity to trypsin. Shrinkage-temperature measurements and sensitivity to collagenase served as indices of crosslinking. UV or DHT crosslinking increased the collagen-fiber shrinkage temperature, resistance to degradation in collagenase, and durability under load in collagenase. However, in trypsin solutions, solubility was significantly increased for UV (approximately 11%) or DHT (approximately 15%) crosslinked fibers compared with uncrosslinked fibers (approximately 4%). Size-exclusion chromatography indicated that no intact collagen alpha-chains were present in the soluble fraction of fibers exposed to trypsin (MW < 1 kD). Interestingly, UV-crosslinked collagen fibers remained intact an order of magnitude longer (4840 +/- 739 min) than DHT-crosslinked (473 +/- 39 min) or uncrosslinked (108 +/- 53 min) fibers when placed under load in trypsin solutions. These data indicate that mechanical loading during incubation in a trypsin solution measures denaturation effects not detected by the trypsin-solubility assay. Our results suggest that DHT-crosslinked collagen fibers should not be used as load-bearing implants. UV-crosslinked fibers may retain more native structure and should exhibit greater resistance to nonspecific proteases in vivo.

Development of fibroblast-seeded ligament analogs for ACL reconstruction.

We fabricated "ligament analogs" in vitro by seeding high-strength resorbable collagen fiber scaffolds with intraarticular (anterior cruciate ligament, ACL) or extraarticular (patellar tendon, PT) rabbit fibroblasts. Fibroblasts attached, proliferated, and secreted new collagen on the ligament analogs in vitro. Fibroblast function depended on the tissue culture substrate (ligament analog vs. tissue culture plate) and the origin of the fibroblasts (ACL vs. PT) PT fibroblasts proliferated more rapidly than ACL fibroblasts when cultured on ligament analogs. Collagen synthesis by ACL and PT fibroblasts was approximately tenfold greater on ligament analogs than on tissue culture plates. The composition, structure, and geometry of the collagen fiber scaffolds may promote collagen synthesis within ligament analogs in vitro. Ligament analogs roughly approximate the structure and strength of native ligament tissue. Ongoing in vivo studies suggest that autogenous fibroblast-seeded ligament analogs remain viable after implantation into the knee joint. With further development, ligament analogs may be useful as implants for ACL reconstruction surgery.

Physical crosslinking of collagen fibers: comparison of ultraviolet irradiation and dehydrothermal treatment.

The strength, resorption rate, and biocompatibility of collagenous biomaterials are profoundly influenced by the method and extent of crosslinking. We compared the effects of two physical crosslinking methods, ultraviolet irradiation (UV) (254 nm) and dehydrothermal (DHT) treatment, on the mechanical properties and molecular integrity of collagen fibers extruded from an acidic dispersion of type I bovine dermal collagen. Collagen fibers exposed to UV irradiation for 15 min had ultimate tensile strength (54 MPa) and modulus (184 MPa) values greater than or equivalent to values for fibers crosslinked with DHT treatment for 3 or 5 days. UV irradiation is a rapid and easily controlled means of increasing the mechanical strength of collagen fibers. Characterization of collagen extracted from the crosslinked samples by dilute acetic acid and limited pepsin digestion indicate that both UV and DHT treatments cause fragmentation of at least a portion of the collagen molecules. Partial loss of the native collagen structure may influence attachment migration, and proliferation of cells on collagen fiberbased ligament analogs. These issues are currently being addressed in our laboratory.

Expert panel method for nurse staffing and resource management.

The Expert Panel Nurse Staffing and Resource Management Method is a bold new approach for the identification of nurse staffing requirements and the management of resources. Expert panels comprised of those most knowledgeable of the patient population and the uniqueness of specific patient care areas identify staff needed to meet clinical, administrative, education, continuous quality improvement, and research needs. In addition, the expert panels explore opportunities for systems improvements, work redesign, and administrative restructuring within the context of budgetary realities.

A study of the relationship between mineral content and mechanical properties of turkey gastrocnemius tendon.

The vertebrate skeletal system undergoes adaptation in response to external forces, but the relation between the skeletal changes and such forces is not understood. In this context, the variation in the amount and location of calcification has been compared with changes in mechanical properties of the normally mineralizing turkey gastrocnemius tendon using ash weight measurements, X-ray radiography, and mechanical testing. Radiographic evidence from 12- to 17-week-old birds showed calcification in only portions of gastrocnemius tendons proximal to the tarsometatarsal joint. Mechanical testing of these dissected proximal regions demonstrated an increased ultimate stress and modulus and a decreased maximum strain that appeared to parallel calcification. Further, stress-strain curves of portions of uncalcified turkey gastrocnemius tendon were shaped similar to those of other typical unmineralized tendon curves while highly calcified tendons yielded curves resembling those of bone. The proximal portions of the gastrocnemius where mineralization begins were observed to have a decreased tendon cross-sectional area compared with distal portions which do not mineralize. Based on the resultant measures of mineral content and location and mechanical properties, it is hypothesized that increased calcification is a result of increased stresses at certain locations of the tendon, perhaps the consequence of the natural forces exerted by the large leg muscles of the bird into which the gastrocnemius inserts. More specifically, tendon calcification may be the result of stress-induced exposure of charged sites on the surfaces of collagen molecules, fibrils, or fibers so that deposition of mineral and subsequent mechanical reinforcement occur in the tissue.(ABSTRACT TRUNCATED AT 250 WORDS)

Effect of Ca/P coating resorption and surgical fit on the bone/implant interface.

The effect of coating resorption on bone apposition and attachment strength to resorbable hydroxyapatite (HA), nonresorbable HA-coated, and uncoated rough titanium implants was evaluated in interference- and noninterference-fit (gap of 2-3 mm) surgical models 2, 4, and 12 weeks postoperatively. Interference and noninterference fits showed differences in bone bridging. Bone apposition was circumferential around the implants in noninterference fit. Significantly greater bone apposition was seen to nonresorbable HA-coated implants than uncoated and resorbable HA-coated implants at 4 and 12 weeks. Only resorbable HA coatings showed significantly lower bone apposition for noninterference versus interference fit and from 4-12 weeks. At 2 weeks, strengths of bone attachment to resorbable HA-coated implants were greater than the other implants, and decreased to lower values (not significant) than the nonresorbable HA-coated implants at 4 and 12 weeks. Differences in push-out shear strengths between interference- and noninterference-fit surgical models were significant for uncoated implants at 4 weeks, but not for HA-coated implants at any time period. Significant differences were seen between the three implant types only for the noninterference-fit model, where the HA-coated implants showed greater strengths than the uncoated implants (significant at 2 and 4 weeks). This study showed that presence of resorbable or nonresorbable HA coatings is beneficial when a gap of 2-3 mm is present between the implant and the bone. The resorbable HA-coated implants showed greatest strengths at the early time period. At later time periods, resorbable HA-coated implants showed lower bone apposition and attachment strengths than nonresorbable HA coatings.(ABSTRACT TRUNCATED AT 250 WORDS)

Intraosseous incorporation of composite collagen prostheses designed for ligament reconstruction.

Composite collagen prostheses are potentially useful for reconstruction of the anterior cruciate ligament (ACL). We evaluated the intraosseous response to composite collagen prostheses to determine if "biological fixation" could be used to secure the prostheses within surgical bone tunnels. The rate of degradation of the prosthesis and the response of the tissue were evaluated, as a function of collagen crosslinking agent and time, in nonloaded bone tunnels in rabbits. Prostheses were fabricated by the alignment of 200 reconstituted type-I collagen fibers (60 microns in diameter) and the embedding of the fibers within a collagen matrix. The prostheses degraded rapidly within the bone tunnels in comparison with soft-tissue implantation sites. Dehydrothermal-cyanamide crosslinked collagen fibers were completely degraded by 8 weeks. Only 10% of glutaraldehyde cross-linked collagen fibers remained intact at 12 weeks. Fibrous tissue and inflammatory cells rapidly infiltrated the prostheses, and new bone surrounded the circumference of the prostheses, advancing toward the center at longer times. At the lateral cortex, where fibrous tissue emerged, the bone/soft-tissue interface was delineated by a tidemark, similar to that observed in a normal ligament insertion site. Preliminary pull-out testing of the soft tissue from the bone was discontinued because failure consistently occurred in the soft tissue; this suggests rapid incorporation of the prostheses within the bone tunnels. Composite collagen prostheses designed for ACL reconstruction degrade rapidly in bone and induce rapid ingrowth of fibrous tissue and bone. These results suggest that tissue ingrowth in the bone tunnels might provide biological fixation for collagen prostheses used for ACL reconstruction.

Optimization of extruded collagen fibers for ACL reconstruction.

Collagen fibers used in a scaffolding device for ligament reconstruction must be thin, strong, and degradable. The purpose of this study was to determine the effects of fiber diameter (20, 50, or 90 microns), crosslinking agent (uncrosslinked, dehydrothermal-cyanamide, or glutaraldehyde), and hydration on the initial mechanical properties, biocompatibility, and subcutaneous degradation rates of fibers extruded from an acidic dispersion of insoluble type I collagen. The wet tensile strength of extruded collagen fibers was significantly improved by decreasing the fiber diameter. Low-diameter, crosslinked fibers had wet tensile strengths ranging from 75-110 MPa. In contrast, high diameter fibers had wet strength values of about 30 MPa. The degradation rate of the implanted fibers, in contrast, was not significantly prolonged by changing the initial fiber diameter. This result is important because prolonged degradation of the fibers can lead to implant encapsulation instead of neoligament formation. By minimizing the diameter, fiber strength can be increased without prolonging the fiber degradation rate. Low-diameter, dehydrothermal-cyanamide crosslinked fibers have greater tensile strength and a more rapid degradation rate than medium-diameter, glutaraldehyde crosslinked fibers, and are therefore more suitable for use in a degradable ligament reconstruction device.

Mechanical and histological evaluation of amorphous calcium phosphate and poorly crystallized hydroxyapatite coatings on titanium implants.

The effect of amorphous calcium phosphate (Ca/P) and poorly crystallized (60% crystalline) hydroxyapatite (HA) coatings on bone fixation to "smooth" and "rough" (Ti-6A1-4V powder sprayed) titanium-6Al-4V (Ti) implants was investigated. Implants were evaluated histologically, mechanically, and by scanning electron microscopy (SEM) after 4 and 12 weeks of implantation in a rabbit transcortical femoral model. Histological evaluation of amorphous vs. poorly crystallized HA coatings showed significant differences in bone apposition (for rough-coated implants only) and coating resorption (for smooth- and rough-coated implants) that were increased within cortical compared to cancellous bone. The poorly crystallized HA coatings showed most degradation and least bone apposition. Mechanical evaluation, however, showed no significant differences in push-out shear strengths between the two types of coatings evaluated. Differences between 4 and 12 weeks were significant for coating resorption and push-out shear strength but not for bone apposition. Significant enhancement in interfacial shear strengths for bioceramic coated as compared to uncoated implants were seen for smooth-surfaced implants (3.5-5 times greater) but not for rough-surfaced implants at 4 and 12 weeks. Rough implants showed greater mean interfacial strengths than uncoated smooth implants at 4 and 12 weeks (seven times greater) and to coated smooth implants at 12 weeks only (two times greater). Mechanical failure of the bone/coating/implant interface consistently occurred within the bone, even in the case of the poorly crystallized HA coatings, which had almost completely resorbed on rough implants. These results suggest that once early osteointegration is achieved biodegradation of a bioactive coating should not be detrimental to the bone/coating/implant fixation.

In vitro evaluation of amorphous calcium phosphate and poorly crystallized hydroxyapatite coatings on titanium implants.

Studies of various apatite coatings on metal orthopaedic prostheses suggest that coating dissolution may promote enhanced bone bonding. Little is known concerning the effects of crystallinity and the underlying roughness on calcium phosphate (Ca/P) coating dissolution rate. To address these issues, the surface chemistry of amorphous Ca/P and poorly crystallized hydroxyapatite (HA) coatings on "smooth" and "rough" titanium (Ti) alloy (Ti-6A1-4V) implants was studied following immersion in Hank's physiologic solution at pH 7.2 and 5.2 for 0-, 4-, and 12-week periods. Changes in Calcium (Ca) ion concentrations in the solutions, coating chemistry, and surface morphology were studied by ion selective electrode, x-ray diffraction (XRD), and scanning electron microscopy (SEM) respectively. The amount of Ca dissolved from Ca/P-coated implants was strongly dependent on the chemistry of the coating and less dependent on pH or time of incubation. The effect of the underlying surface (smooth vs. rough) was not significant. The poorly crystallized HA coating underwent the most degradation, greatest crystallographic alteration, and greatest surface film formation. The amorphous coating was more stable in the saline environment, and may be more suitable in vivo if coating longevity is desired. These results suggest that this in vitro method is an effective way of determining differences in HA coating integrity.