Optical Link as an Alternative for MRI Receive Coils: Toward a Passive Approach.

OBJECTIVE: The objective of this work was to propose an alternative solution to NMR signal transmission by replacing the coaxial cables of the receiver radiofrequency (RF) coil in the context of MRI so as to improve safety. Starting from the analysis of previous studies and reports on the topic, the difficulty of supplying power wirelessly to an RF coil was identified. To avoid this difficult task, the development of a passive analog optical link was studied. METHODS: In order to quantify the requirements for achieving an analog conversion, the performance of the link was evaluated based on the input NMR signal amplitude and the optical power and compared with that of a galvanic link. Acquisitions were performed on a 7-T preclinical MRI system with a doped saline solution as phantom. A passive and MRI-compatible polarization-state custom-made modulator was tested as well as a commercial Mach-Zehnder interferometer. RESULTS: The conversion was not sensitive enough to keep similar SNRs, but the main source of noise was identified along with parameters for improvement. Optical power emitted by the laser, insertion loss, and full-phase inversion voltage of the modulators were found to be crucial characteristics for the application. These data indicate that custom application devices are required since the frequency, bandwidth, and amplitude of NMR signals are quite different to usual telecommunication signals. CONCLUSION: An electro-optic modulation and a transmission channel were successfully conceived and tested. Images were reconstructed with some significant SNR drawbacks that are expected to be compensated with an appropriate modulator. SIGNIFICANCE: While technical challenges remain, our approach to a two-decades-long problem could solve a major issue of MRI safety by removing the need for supplying on-coil electrical current.

Electro-optic probe for real-time assessments of RF electric field produced in an MRI scanner: Feasibility tests at 3 and 4.7 T.

During magnetic resonance imaging (MRI) examinations, the average specific absorption rate (SAR) of the whole body is calculated as an index of global energy deposition in biological tissue without taking into account the presence of metallic implants or conductive materials. However, this global SAR calculation is not sufficient to ensure patient safety and a local SAR measurement should be carried out. Several measurement techniques have already been used to evaluate the local SAR, in particular electric field (E-field) probes, but the accuracy of the measurements and the resolutions (spatial and temporal) depend strongly on the measurement method/probe. This work presents an MR-compatible, subcentimeter probe based on an electro-optic (EO) principle enabling a real-time measurement of the local E-field during MRI scans. The experiments using these probes were performed on two different MR systems (preclinical and clinical) having different static magnetic field strengths and with different volume coil geometries. The E-field was measured with unloaded (in air) and loaded volume coils in order to assess the sensing characteristics of the optical probe. The results show an excellent linearity between the measured E-field and the radiofrequency (RF) magnetic field in both experimental conditions. Moreover, the distribution of the E-field throughout the volume coil was experimentally determined and was in good agreement with numerical simulations. Finally, we demonstrate through our measurements that the E-field depends strongly on the dielectric properties of the medium.

Terahertz encoding approach for secured chipless radio frequency identification.

In this article, we present a new family of chipless tags, which permit encoding of digital data in the terahertz domain. These devices consist of stacked dielectric media whose thicknesses are of the same order as terahertz wavelengths. Since the information is encoded in the volume of these multilayer terahertz tags, they can easily be associated with classical identification techniques (e.g., barcode, radio frequency identification), where information is encoded at the surface of the tag, to provide higher data security. The principle of this encoding approach is studied and experimentally demonstrated in this paper. A 2 bit tag prototype has been realized and measured for validation purposes.

Electric field and temperature measurement using ultra wide bandwidth pigtailed electro-optic probes.

We present pigtailed electro-optic probes that allow a simultaneous measurement of high frequency electric fields and temperature using a unique laser probe beam. This has been achieved by the development of a novel probe design associated with a fully automated servo-controlled optical bench, initially developed to stabilize the electric field sensor response. The developed electro-optic probes present a stable response in outdoors conditions over a time duration exceeding 1 h, a frequency bandwidth from kHz to tens of GHz with a sensitivity of 0.7 Vm(-1)Hz(-(1/2)), and a temperature accuracy of 40 mK.

High-finesse Fabry-Perot electro-optic sensors with enhanced sensitivity and high spatial resolution.

We present a high-finesse optical cavity containing a LiTaO(3) electro-optic crystal, devoted to free-space electric field characterization. Theoretical considerations will show that the modulation depth is directly related to the transversal components of the field to be measured, thus opening the way to vectorial mapping of the electric field using a single electro-optic crystal. Also, a discussion about noise and sensitivity will be given. As the latter increases with the effective cavity length, and bandwidth decreases, a trade-off is realized, allowing us to measure an electric field of 60 mV/m/ sqrt[Hz] in a 110 MHz bandwidth. Cavity dimensions are less than 8 mm(3), giving an inner-crystal transverse spatial resolution of 70 microm and allowing pigtailed systems to integrate.

Time-domain terahertz study of defect formation in one-dimensional photonic crystals.

One-dimensional photonic crystals composed of silicon and air layers with and without twinning defect (i.e., a periodicity break where one half of the photonic structure is a mirror image of the other one) are studied by means of terahertz time-domain transmission and reflection spectroscopy. The structure with defect is decomposed into building blocks: two twins and a defect. A phase-sensitive characterization in transmission and reflection allows us to fully determine the transfer matrices of any block and consequently to predict the properties of composed structures regardless of the microstructure of the constituting blocks. It is shown and experimentally demonstrated that the defect level position is controlled by the reflectance phase of the twins. Possible approach of the reflectance phase determination by use of Kramers-Kronig analysis is also discussed.

Grating-assisted coupling of terahertz waves into a dielectric waveguide studied by terahertz time-domain spectroscopy.

We report on the efficient coupling of terahertz (THz) waves into a dielectric waveguide by means of a diffraction grating engraved at the top of the waveguide. The waveguide is made of a 201-microm-thick high-resistivity silicon wafer. The transmission of the device, measured versus frequency by terahertz time-domain spectroscopy, shows usual m lines when a frequency component of the THz pulse spectrum satisfies the phase-matching condition and is coupled into the waveguide. The experimental data are well modeled with the differential electromagnetic method to compute the diffraction pattern of the grating device. The dispersion curve of the first four modes of propagation is determined from the frequency position of the m lines recorded for different angles of incidence of the THz beam. The waveguide exhibits a weak group velocity dispersion at high frequencies.