Three-dimensional assessment of proximal contact enamel using optical coherence tomography.

OBJECTIVE: The purpose of this study was to detect and investigate the association of enamel microcracks with demineralization at proximal contact areas of premolars, using 3D swept-source optical coherence tomography (SS-OCT). METHODS: Extracted maxillary and mandibular premolars (n=50 each), without any visible tooth cracks, were examined for demineralization of interproximal contact areas, using the International Caries Detection and Assessment System (ICDAS). SS-OCT was used to evaluate demineralization and detect microcracks. Demineralization progression was divided into 4 types by depth: 0 for sound enamel and Type I, II, and III for enamel demineralization penetrating into the outer third, the middle third, and the inner third of the enamel thickness, respectively. Enamel microcracks were classified according to the predominant crack pattern: Type O, no cracks; Type A, subsurface microdefects; Type B, enamel microcrack running along the direction of the enamel prism; Type C, enamel microcrack running transverse to the enamel prism direction; and Type D, a combination of patterns A, B, and C. SS-OCT findings were confirmed by confocal laser scanning microscopy observation. RESULTS: Microcracks confined within the superficial enamel in proximal contact areas were seen as bright lines on SS-OCT. There were significant positive correlations among ICDAS codes, demineralization levels, and microcrack distribution (p≤0.001). The mesial side of maxillary premolars showed significantly more demineralization (n=36) and microcracks (n=27) than that of the mandibular premolars (n=20 and n=14, respectively; p<0.001). SIGNIFICANCE: The presence of microcracks within the superficial enamel in proximal contact areas could be determined using SS-OCT, and correlated with the level of demineralization. 3D SS-OCT is a valuable diagnostic tool for comprehensive assessment of microstructural changes related to enamel demineralization and crack development.

Effect of lights with various wavelengths on bleaching by 30% hydrogen peroxide.

The objective of this study was to evaluate the bleaching effect of light sources with various wavelengths using 30% hydrogen peroxide (HP) in vitro. The hematoporphyrin-stained paper was bleached with HP and irradiated for 10 min using LED light sources with 265, 310, 365, 405, or 450 nm respectively. In control group, HP was applied for 10 min without light irradiation. The bleaching procedure was repeated two times. The L*a*b* values of the samples before bleaching and after each bleaching step were measured using a colorimeter. Color changes of specimens were then calculated and statistically analyzed. There was an interaction between light sources and time of irradiation in the color change (p < 0.05). Time and light sources significantly affected ΔE and ΔL (p < 0.05). The light source of 256 nm showed the highest bleaching effect over time followed by that of 310 nm, which were statistically different from other groups (p < 0.001). The 365 nm, 450 nm groups, and control group showed low bleaching effect visually with no significant differences in ΔE and ΔL (p > 0.05). It was concluded that the wavelengths of the light sources affected the bleaching by HP. The 310-nm light can be a potential source for bleaching.

Comparison of resin-based and glass ionomer sealants with regard to fluoride-release and anti-demineralization efficacy on adjacent unsealed enamel.

This study compared resin-based and glass ionomer sealants with regard to their fluoride-release behavior and anti-demineralization potential on adjacent unsealed enamel surfaces. Sealant cavities prepared on bovine enamel blocks were filled with fluoride-containing resin sealants [TeethmateF-1 (TF), ClinproTM (CP)], and glass ionomer sealant [Fuji VII (FVII)]. Specimens were then incubated in artificial saliva for 14 days to measure fluoride. Thereafter, demineralization was performed for 10 days, and the anti-demineralization efficacy was assessed by Swept Source Optical Coherence Tomography (SS-OCT), and cross-sectional nanohardness. All data were statistically analyzed by using ANOVA. FVII exhibited the highest fluoride release. SS-OCT and nanohardness findings indicated that anti-demineralization efficacy of TF was the greatest, whereas FVII was not significantly different from that of CP. Resin sealants released a lower amount of fluoride but exhibited anti-demineralization effects on the adjacent unsealed enamel surfaces that were comparable to that of a glass ionomer sealant.