A NiS2/C composite as an innovative anode material for sodium-ion batteries: ex situ XANES and EXAFS studies to investigate the sodium storage mechanism.

The successful deployment of sodium-ion batteries (SIBs) requires high-performance sustainable and cost-effective anode materials having a high current density. In this regard, sodium disulphide (NiS2) has been prepared as a composite with activated carbon (C) using a facile hydrothermal synthesis route in the past. The X-ray diffraction pattern of the as-prepared NiS2/C composite material shows well-defined diffraction peaks of NiS2. Most carbonaceous materials are amorphous, and the Brunauer-Emmett-Teller (BET) study shows that the surface area is close to 148 m2 g-1. At a current density of 50 mA g-1, the NiS2/C composite exhibits a high capacity of 480 mA h g-1 during the initial cycle, which subsequently decreases to 333 mA h g-1 after the completion of the 100th cycle. The NiS2/C composite electrode provides an exceptional rate capability by delivering a capacity of 270 mA h g-1 at a high current density of 2000 mA g-1, suggesting the suitability of the NiS2/C composite for SIBs. Ex situ X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) analyses at the Ni K-edge have been used to examine the type of chemical bonding present in the anode and also how it changes during electrochemical redox cycling. The understanding of the sodium storage mechanism is improved by the favorable results, which also offer insights for developing high-performance electrode materials for rechargeable SIBs.

Effect of Pd-Sensitization on Poisonous Chlorine Gas Detection Ability of TiO2: Green Synthesis and Low-Temperature Operation.

Ganoderma lucidum mushroom-mediated green synthesis of nanocrystalline titanium dioxide (TiO2) is explored via a low-temperature (≤70 °C) wet chemical method. The role of Ganoderma lucidum mushroom extract in the reaction is to release the ganoderic acid molecules that tend to bind to the Ti4+ metal ions to form a titanium-ganoderic acid intermediate complex for obtaining TiO2 nanocrystallites (NCs), which is quite novel, considering the recent advances in fabricated gas sensing materials. The X-ray powder diffraction, field emission scanning electron microscopy, Raman spectroscopy, and Brunauer-Emmett-Teller measurements etc., are used to characterize the crystal structure, surface morphology, and surface area of as-synthesized TiO2 and Pd-TiO2 sensors, respectively. The chlorine (Cl2) gas sensing properties are investigated from a lower range of 5 ppm to a higher range of 400 ppm. In addition to excellent response-recovery time, good selectivity, constant repeatability, as well as chemical stability, the gas sensor efficiency of the as-synthesized Pd-TiO2 NC sensor is better (136% response at 150 °C operating temperature) than the TiO2 NC sensor (57% at 250 °C operating temperature) measured at 100 ppm (Cl2) gas concentration, suggesting that the green synthesized Pd-TiO2 sensor demonstrates efficient Cl2 gas sensing properties at low operating temperatures over pristine ones.

Author Correction: Low-Temperature Ionic Layer Adsorption and Reaction Grown Anatase TiO2 Nanocrystalline Films for Efficient Perovskite Solar Cell and Gas Sensor Applications.

A correction to this article has been published and is linked from the HTML and PDF versions of this paper. The error has not been fixed in the paper.

Low-Temperature Ionic Layer Adsorption and Reaction Grown Anatase TiO2 Nanocrystalline Films for Efficient Perovskite Solar Cell and Gas Sensor Applications.

A low-temperature (90 °C) and directly grown anatase titanium dioxide (TiO2) nanocrystalline film using successive ionic layer adsorption and reaction (SILAR) for perovskite solar cell and gas sensor applications. TiO2 nanocrystalline electron transfer layer (ETL) improves the power conversion efficiency (PCE) of perovskite solar cells due to faster charge transport kinetics as well as slower charge recombination process. The optimized TiO2 nanocrystalline ETL (15 L) demonstrates as high as ~10% PCE with a short circuit current density of 18.0 mA/cm2, open circuit voltage of 0.81 V and fill factor of 66.3% in perovskite solar cells. Furthermore, room-temperature ammonia sensing characteristics of TiO2 nanocrystalline film (25 L) were  demonstrated for various concentration levels of ammonia in dry air conditions. A high room-temperature response of 80% was achieved at 100 ppm of ammonia with rapid response and recovery signatures of 30 and 85 s, and nearly fifteen days stability, respectively. The response of the sensor to other gases such as formaldehyde, petrol, ethanol acetone, and ammonia etc, indicated a high selectivity towards volatile organic compounds of ammonia gas. The room temperature operation, with high selectivity, repeatability and fast transition times, suggests potentially useful in flexible and cost-effective production in optoelectrochemical device technology.

Natural Carbonized Sugar as a Low-Temperature Ammonia Sensor Material: Experimental, Theoretical, and Computational Studies.

Carbonized sugar (CS) has been synthesized via microwave-assisted carbonization of market-quality tabletop sugar bearing in mind the advantages of this synthesis method, such as being useful, cost-effective, and eco-friendly. The as-prepared CS has been characterized for its morphology, phase purity, type of porosity, pore-size distribution, and so on. The gas-sensing properties of CS for various oxidizing and reducing gases are demonstrated at ambient temperature, where we observe good selectivity toward liquid ammonia among other gases. The highest ammonia response (50%) of a CS-based sensor was noted at 80 °C for 100 ppm concentration. The response and recovery times of the CS sensor are 180 and 216 s, respectively. This unveiling ammonia-sensing study is explored through a plausible theoretical mechanism, which is further well-supported by computational modeling performed using density function theory. The effect of relative humidity on the CS sensor has also been studied at ambient temperature, which demonstrated that the minimum and maximum (20-100%) relative humidity values revealed 16 and 62% response, respectively.