Prevalence of middle mesial and middle distal canals in mandibular molars in an Egyptian subpopulation using micro-computed tomography.

OBJECTIVES: To study the prevalence of middle mesial and middle distal canals in permanent mandibular molars in Egyptian subpopulation using micro-computed tomography. MATERIALS AND METHODS: Two hundred and forty extracted mandibular permanent molars of Egyptian patients were scanned using micro-computed tomography, then the images were reconstructed to allow for the detection of the middle mesial (MM) and middle distal (MD) canals of the molars examined. The path of each extra canal was studied to determine the configuration of each canal. Data were analyzed statistically using the Chi-square test with a level of significance set at P< 0.05. RESULTS: The evaluation of three-dimensional (3D) images of this study showed that no significant difference was found between the percentage of MM (27.5%) and MD canals (22.5%) (P = 0.2064); however, there was a significant difference between the percentage of teeth having both extra canals (10%) and teeth having only one of these canals (P < 0.05). The confluent configuration (71%) was significantly higher than the other configurations (P < 0.05). CONCLUSION: A higher percentage of MM canal was detected followed by the MD canal. The least significant was both canals occurring within the same molar. The percentage of the confluent configuration was the highest. The apt knowledge of the variations of the root canal system anatomy and the respect of the discrepancies associated with diverse demographic areas will ensure the proper management of each tooth with endodontic involvement and its long-term success.

Apical extrusion of debris after canal shaping with three single-file systems.

OBJECTIVES: The aim of this study was to evaluate the quantity of apically extruded debris after canal shaping with three single-file systems. MATERIALS AND METHODS: Sixty mesiobuccal canals of mandibular molars were divided into three experimental groups according to the used file systems-WaveOne Gold, RECIPROC Blue, and HyFlex EDM One file. Debris extruded during canal shaping were collected in preweighed vials. Each canal was irrigated with 5 mL of distilled water via a 30 G side-vented needle. The amount of the debris extruded from each canal was calculated by subtracting the preinstrumentation from postinstrumentation measurement. The preparation times were recorded. Data were analyzed using analysis of variance (ANOVA) and posthoc Tukey tests with α = 0.05. RESULTS: WaveOne Gold extruded the least amount of debris. Results between WaveOne Gold and HyFlex EDM were significantly different. No significant differences in canal shaping time were detected among the three groups (P > 0.05). CONCLUSION: WaveOne Gold showed the best results regarding apical debris extrusion. Difference between WaveOne Gold and HyFlex EDM suggests that file design and motion kinematics affect the quantity of debris extrusion.

From manual periodontal probing to digital 3-D imaging to endoscopic capillaroscopy: Recent advances in periodontal disease diagnosis.

Deepened periodontal pockets exert a significant pathological burden on the host and its immune system, particularly in a patient with generalized moderate to severe periodontitis. This burden is extensive and longitudinal, occurring over decades of disease development. Considerable diagnostic and prognostic successes in this regard have come from efforts to measure the depths of the pockets and their contents, including level of inflammatory mediators, cellular exudates and microbes; however, the current standard of care for measuring these pockets, periodontal probing, is an analog technology in a digital age. Measurements obtained by probing are variable, operator dependent and influenced by site-specific factors. Despite these limitations, manual probing is still the standard of care for periodontal diagnostics globally. However, it is becoming increasingly clear that this technology needs to be updated to be compatible with the digital technologies currently being used to image other orofacial structures, such as maxillary sinuses, alveolar bone, nerve foramina and endodontic canals in 3 dimensions. This review aims to summarize the existing technology, as well as new imaging strategies that could be utilized for accurate evaluation of periodontal pocket dimensions.

Application of radiopaque micro-particle fillers for 3-D imaging of periodontal pocket analogues using cone beam CT.

BACKGROUND: Periodontitis is an infectious/inflammatory disease most often diagnosed by deepening of the gingival sulcus, which leads to periodontal pockets (PPs) conventional manual periodontal probing does not provide detailed information on the three-dimensional (3-D) nature of PPs. OBJECTIVES: To determine whether accurate 3-D analyses of the depths and volumes of calibrated PP analogues (PPAs) can be obtained by conventional cone beam computed tomography (CBCT) coupled with novel radiopaque micro-particle fillers (described in the companion paper) injected into the PPAs. METHODS: Two PPA models were employed: (1) a human skull model with artificial gingiva applied to teeth with alveolar bone loss and calibrated PPAs, and (2) a pig jaw model with alveolar bone loss and surgically-induced PPAs The PPAs were filled with controlled amounts of radiopaque micro-particle filler using volumetric pipetting Inter-method and intra-method agreement tests were then used to compare the PPA depths and volumes obtained from CBCT images with values obtained by masked examiners using calibrated manual methods. RESULTS: Significant inter-method agreement (0.938-0.991) and intra-method agreement (0.94-0.99) were obtained when comparing analog manual data to digital CBCT measurements enabled by the radiopaque filler. SIGNIFICANCE: CBCT imaging with radiopaque micro-particle fillers is a plausible means of visualizing and digitally assessing the depths, volumes, and 3-D shapes of PPs This approach could transform the diagnosis and treatment planning of periodontal disease, with particular initial utility in complex cases Efforts to confirm the clinical practicality of these fillers are currently in progress.

Development of radiopaque, biocompatible, antimicrobial, micro-particle fillers for micro-CT imaging of simulated periodontal pockets.

OBJECTIVES: Approximately 109 bacteria can be harbored within periodontal pockets (PP) along with inflammatory byproducts implicated in the pathophysiology of systemic diseases linked to periodontitis (PD). Calculation of this inflammatory burden has involved estimation of total pocket surface area using analog data from conventional periodontal probing which is unable to determine the three-dimensional (3-D) nature of PP. The goals of this study are to determine the radiopacity, biocompatibility, and antimicrobial activity of transient micro-particle fillers in vitro and demonstrate their capability for 3-D imaging of artificial PP (U.S. Patent publication number: 9814791 B2). METHODS: Relative radiopacity values of various metal oxide fillers were obtained from conventional radiography and micro-computed tomography (µCT) using in vitro models. 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays were used to measure the biocompatibility of calcium tungstate (CaWO4) particles by determination of viable keratinocytes percentage (%) after exposure. After introducing an antibacterial compound (K21) to the radiopaque agent, antimicrobial tests were conducted using Porphyromonas gingivalis (P. gingivalis) and Streptococcus gordonii (S. gordonii) strains and blood agar plates. RESULTS: CaWO4 micro-particle-bearing fillers exhibited an X-ray radiopacity distinct from tooth structures that enabled 3-D visualization of an artificial periodontal pocket created around a human tooth. MTT assays indicated that CaWO4 micro-particles are highly biocompatible (increasing the viability of exposed keratinocytes). Radiopaque micro-particle fillers combined with K21 showed significant antimicrobial activity for P. gingivalis and S. gordonii. SIGNIFICANCE: The plausibility of visualizing PP with 3-D radiographic imaging using new radiopaque, biocompatible, transient fillers was demonstrated in vitro. Antibacterial (or other) agents added to this formula could provide beneficial therapeutic features along with the diagnostic utility.