Effect of short glass fibers on the polymerization shrinkage stress of dental composite.

This study examines contraction stresses of seven short fiber reinforced composites (sFRC) exhibiting different volume loads and aspect ratios (AR)* of fibres. The shift towards a greater utilization of posterior resin composites in dentistry has seen increased interest in the use of randomly oriented short glass fibers in these restorative materials. While the effect of these fibers on modulus, strength, and toughness has been studied, very little information exists on their effect on polymerization shrinkage and even less on shrinkage stress. S2-glass fibers with an average AR of 68 were used to form three experimental groups with 5%, 10%, and 20% volume loads. Commercial sFRC with ARs of 20 and 100 were also tested. A tensilometer set up was used with moderate compliance, 5.4 J/cm2 irradiance, and a C-factor of 2.75. Data was statistically analyzed using ANOVA followed by post hoc Tukey's test. The addition of 5% of the experimental fiber did not significantly increase stress while the 10% and 20% groups resulted in 36.3% and 39.1% higher stress values, respectively, compared to the non-fiber control group (p < 0.05). Of all the sFRC groups, the very low AR material exhibited the lowest stress [0.682 MPa (p = 0.001)] while another commercial material with higher AR fibers exhibited the highest overall value [1.822 MPa (p < 0.001)] when compared to the control group. The results indicate that both short fiber volume and AR are important variables to consider with regards to setting stresses of sFRC. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1930-1937, 2017.

Effect of aluminum oxide addition on the flexural strength and thermal diffusivity of heat-polymerized acrylic resin.

PURPOSE: This work was undertaken to investigate the effect of adding from 5% to 20% by weight aluminum oxide powder on the flexural strength and thermal diffusivity of heat-polymerized acrylic resin. MATERIALS AND METHODS: Seventy-five specimens of heat-polymerized acrylic resin were fabricated. The specimens were divided into five groups (n = 15) coded A to E. Group A was the control group (i.e., unmodified acrylic resin specimens). The specimens of the remaining four groups were reinforced with aluminum oxide (Al2O3) powder to achieve loadings of 5%, 10%, 15%, and 20% by weight. Specimens were stored in distilled water at 37 degrees C for 1 week before flexural strength testing to failure (5 mm/min crosshead speed) in a universal testing machine. Results were analyzed by one-way analysis of variance and post hoc Tukey paired group comparison tests (p < 0.05). Weibull analysis was used to calculate the Weibull modulus, characteristic strength, and the required stress for 1% and 5% probabilities of failure. Cylindrical test specimens (5 specimens/group) containing an embedded thermocouple were used to determine thermal diffusivity over a physiologic temperature range (0 to 70 degrees C). RESULTS: The mean flexural strength values of the heat-polymerized acrylic resin were (in MPa) 99.45, 119.92, 121.19, 130.08, and 127.60 for groups A, B, C, D, and E, respectively. The flexural strength increased significantly after incorporation of 10% Al2O3. The mean thermal diffusivity values of the heat-polymerized acrylic resin (in m(2)/sec) were 6.8, 7.2, 8.0, 8.5, and 9.3 for groups A, B, C, D, and E, respectively. Thermal diffusivities of the composites were found to be significantly higher than the unmodified acrylic resin. Thermal diffusivity was found to increase in proportion to the weight percentage of alumina filler, which suggested that the proper distribution of alumina powders through the insulating polymer matrix might form a pathway for heat conduction. CONCLUSION: Al2O3 fillers have potential as added components in denture bases to provide increased flexural strength and thermal diffusivity. Increasing the flexural strength and heat transfer characteristics of the acrylic resin base material could lead to more patient satisfaction.

Effect of chemical disinfectants and repair materials on the transverse strength of repaired heat-polymerized acrylic resin.

PURPOSE: The purpose of this study was to evaluate both the effects of immersion in different chemical disinfectant solutions and the type of repair material on the transverse strength of repaired heat-polymerized acrylic resin. MATERIALS AND METHODS: A total of 110 rectangular specimens (65 x 10 x 3 mm) of heat-polymerized acrylic resin (Triplex) were fabricated. After polymerization, the specimens were polished, then stored in distilled water at 37 degrees C for 1 week. The specimens were divided into 11 groups (n = 10) coded A to K. Specimens of Group A remained intact (control). The specimens of Groups C to F and Groups H to K were immersed in the following chemical disinfectant solutions (1%, 2.5%, and 5.25% sodium hypochlorite and 2% glutaraldehyde, respectively) for 10 minutes. The specimens of all groups except those of Group A were sectioned in the middle to create 10 mm gaps and repaired with the same resin (Groups B to F) and autopolymerizing acrylic resin (Groups G to K). The specimens of Groups C to F and Groups H to K were again immersed in the disinfectant solutions in the same sequence. The transverse strength (N/mm(2)) was tested for failure in a universal testing machine, at a crosshead speed of 5 mm/min. Two-way analysis of variance (ANOVA) was performed to evaluate the effects of both the disinfectant solutions and repair materials on the transverse strength of repaired specimens. All data were statistically analyzed using one-way analysis of variance followed by Tukey's test at 95% confidence level. RESULTS: The repaired specimens treated with/without disinfectant solutions showed similar (p > 0.05) transverse strength values. No differences (p > 0.05) were detected among the repaired specimens either with heat-polymerized or autopolymerizing acrylic resins. The intact specimens showed transverse strength values (86.9 +/- 11.8) significantly higher (p < 0.05) than the values of the repaired specimens. CONCLUSIONS: Among the repaired specimens, transverse strength was not affected after immersion in the disinfectants for the immersion period tested (10 min). The repair material, either heat-polymerized or autopolymerizing acrylic resin, had no effect on the transverse strength of the repaired acrylic resin specimens.

Influence of Different Techniques of Laboratory Construction on the Fracture Resistance of Fiber-Reinforced Composite (FRC) Bridges.

The aim of the current investigation is to evaluate optimal pontic and retainer fiber positions for Polyethylene fiber-reinforced composite (FRC) restorations. In series I notch disc specimens were used to mimic loading cuspal regions of pontics. Four groups (n=15/group; codes A to D) were prepared from Artglass composite. Groups A to C were reinforced with polyethylene fibers, and group D was an unreinforced control. Fibers were positioned either around (A), beneath the notch (B), or at the disc base (C). Specimens were stored in distilled water at 37 degrees C for 24 h before testing to failure (CHS=1mm/min) in a universal testing machine. Mean torque to failure values ranked [P< 0.05; one-way analysis of variance (ANOVA)] as follows A = B > C = D. In series II five groups of three unit bridges (n =5/group; codes A to E) were prepared from Artglass dental composite without (group A) or with (groups B to E) different Connect fiber reinforcement locations/techniques. Bridges were cemented using 2 bond resin cement to a standardized substructure. After storage, as per series I, bridges were loaded mid-pontic region to failure. One-way ANOVA showed no significant (P=0.08) difference between test groups. The research hypothesis was that notched disc and 3 unit bridge test techniques would discriminate equally between fiber-reinforced specimens and an unreinforced composite control was rejected.

Fibre-reinforced composites in restorative dentistry.

Restorative dentistry is constantly evolving as a result of innovative treatment solutions based on new materials, treatment techniques and technologies, with composite materials being a prime example. The advent of fibre reinforcement has further increased the potential uses of composites within restorative dentistry. This paper discusses fibre types, structure and the physical properties of fibre-reinforced composites, in addition to outlining some of the potential clinical applications of this exciting group of materials, thus updating the reader on the new treatment possibilities offered by these developments.

Effects of grit blasting and silanization on bond strengths of a resin luting cement to Belleglass HP indirect composite.

PURPOSE: To investigate the extent of bonding possible of a resin luting cement with three opacities of Belleglass HP, representing different filler type and loading levels in a highly cross-linked resin matrix. MATERIALS AND METHODS: Belleglass HP (3 opacities: opaque dentin, translucent dentin, cuspal enamel) was prepared as solid notched discs (Group A) or luted halves to create notched discs (Groups B-F). Luted samples were split through the notch on the Instron for conditions: as-is after molding (B), grit blasted with 50 microm Al2O3 (C), grit blasted and silanated (D) grit blasted, silanated, and stored 1 week (E), and grit blasted and treated with Artglass liquid (F). All the samples were stored in distilled water at 37 degrees C for 24 hours before testing. The fractured surfaces were examined by light and scanning electron microscopy (SEM) to assess the effect of the surface treatments. RESULTS: The mean fracture resistance (+/- S.D) of the tested groups ranged from 7.6 (+/- 1.9 N mm(-1)) for Group A to 13.9 (+/- 5.4 N mm(-1)) for Group D. Two-way analysis of variance showed no significant interaction (P>0.05) between product opacities & surface treatments. The bonded inlay test halves in Groups B and C failed adhesively between the inlay test halves and the luting cement whereas the other three test groups (D,E,F) failed cohesively in the luting cement. One-way analysis of variance with post-hoc paired group Tukey testing revealed that Group D (13.9 +/- 5.4 N mm(-1)) performed significantly better (P<0.05) than Groups A (7.6 +/- 1.9 N mm(-1), B (9.2 +/- 3.7 N mm(-1)) or C (7.8 +/- 1.6 N mm(-1)). No statistical difference was found between Groups D to F (P>0.05).

Influence of fiber type and wetting agent on the flexural properties of an indirect fiber reinforced composite.

STATEMENT OF PROBLEM: Different fiber types are available for reinforcing composite restorations. Little information exists regarding optimal fiber type/bonding agent combinations. PURPOSE: This in vitro study examined the influence of storage time and 2 fiber wetting agents on the flexural properties of an indirect dental composite reinforced by 3 fiber types. MATERIAL AND METHODS: Three types of fiber (ultra-high molecular weight polyethylene, Kevlar, and Glass fiber) were used to reinforce samples of an indirect composite (Artglass) prepared to test flexural properties. Each fiber type was used to prepare 3 groups of 10 specimens after fiber wetting with an unfilled or a filled resin bonding agent. All fibers were weighed to an accuracy of 0.01 mg to standardize the amount of fiber placed in the base (tensile side) of the specimen preparation mold (2 x 2 x 25 mm). Fiber-reinforced samples wetted with the unfilled resin were stored for 24 hours before flexural testing, whereas separate groups of fiber-reinforced samples wetted with the filled resin were tested after both 24 hours and 6 months storage in water at 37 degrees C. Two additional groups of unreinforced composite control specimens (10 samples per group) were prepared, one for each of the 2 storage times, resulting in 11 groups total. Mean flexural strengths (MPa) and flexural modulus (GPa) values were determined in a 3-point bend test at a crosshead speed of 1 mm/min by use of a universal testing machine. Comparisons between means were performed with 2- and 1-way analysis of variance tests (alpha=.01) to demonstrate the influence of storage time, fiber wetting agent, and fiber type on the flexural properties of the indirect dental composite tested. RESULTS: Significant increases (124% to 490%) in mean flexural strength (P<.01) were found for all fiber-reinforced groups in comparison to the unreinforced controls at both storage time intervals. The silane containing unfilled bonding agent gave the greatest reinforcing effect (364%) when used with the glass fiber material. After 6 months storage in water, a significant decline (28%) occurred in the mean flexural strength of the glass fiber-reinforced specimens (P<.01) when the filled bonding agent was used. CONCLUSION: Within the limitations of this study, the choice of fiber type and wetting agent was shown to have a significant positive influence on the flexural properties of the fiber-reinforced composite. When used with the silane containing unfilled bonding agent, the glass fiber increased the mean flexural strength of the unreinforced indirect composite by 364%.