NiOx Passivation in Perovskite Solar Cells: From Surface Reactivity to Device Performance.

Nonstoichiometric nickel oxide (NiOx) is one of the very few metal oxides successfully used as hole extraction layer in p-i-n type perovskite solar cells (PSCs). Its favorable optoelectronic properties and facile large-scale preparation methods are potentially relevant for future commercialization of PSCs, though currently low operational stability of PSCs is reported when a NiOx hole extraction layer is used in direct contact with the perovskite absorber. Poorly understood degradation reactions at this interface are seen as cause for the inferior stability, and a variety of interface passivation approaches have been shown to be effective in improving the overall solar cell performance. To gain a better understanding of the processes happening at this interface, we systematically passivated specific defects on NiOx with three different categories of organic/inorganic compounds. The effects on NiOx and the perovskite (MAPbI3) deposited on top were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Here, we find that the perovskite's structural stability and film formation can be significantly affected by the passivation treatment of the NiOx surface. In combination with density functional theory (DFT) calculations, a likely origin of NiOx-perovskite degradation interactions is proposed. The surface passivated NiOx layers were incorporated into MAPbI3-based PSCs, and the influence on device performance and operational stability was investigated by current-voltage (J-V) characterization, impedance spectroscopy (IS), and open circuit voltage decay (OCVD) measurements. Interestingly, we find that a superior structural stability due to interface passivation must not relate to high operational stability. The discrepancy comes from the formation of excess ions at the interface, which negatively impacts all solar cell parameters.

Influence of Redox Couple on the Performance of ZnO Dye Solar Cells and Minimodules with Benzothiadiazole-Based Photosensitizers.

ZnO-based dye-sensitized solar cells exhibit lower efficiencies than TiO2-based systems despite advantageous charge transport dynamics and versatility in terms of synthesis methods, which can be primarily ascribed to compatibility issues of ZnO with the dyes and the redox couples originally optimized for TiO2. We evaluate the performance of solar cells based on ZnO nanomaterial prepared by microwave-assisted solvothermal synthesis, using three fully organic benzothiadiazole-based dyes YKP-88, YKP-137, and MG-207, and alternative electrolyte solutions with the I-/I3 -, Co(bpy)3 2+/3+, and Cu(dmp)2 1+/2+ redox couples. The best cell performance is achieved for the dye-redox couple combination YKP-88 and Co(bpy)3 2+/3+, reaching an average efficiency of 4.7% and 5.0% for the best cell, compared to 3.7% and 3.9% for the I-/I3 - couple with the same dye. Electrical impedance spectroscopy highlights the influence of dye and redox couple chemistry on the balance of recombination and regeneration kinetics. Combined with the effects of the interaction of the redox couple with the ZnO surface, these aspects are shown to determine the solar cell performance. Minimodules based on the best systems in both parallel and series configurations reach 1.5% efficiency for an area of 23.8 cm2.

Characterization of Photochromic Dye Solar Cells Using Small-Signal Perturbation Techniques.

Photochromic dye-sensitized solar cells (DSSCs) are novel semi-transparent photovoltaic devices that self-adjust their optical properties to the irradiation conditions, a feature that makes them especially suitable for building integrated photovoltaics. These novel solar cells have already achieved efficiencies above 4%, and there are multiple pathways to improve the performance. In this work, we conduct a full characterization of DSSCs with the photochromic dye NPI, combining electrical impedance spectroscopy (EIS) and intensity-modulated photocurrent spectroscopy (IMPS). We argue that the inherent properties of the photochromic dye, which result in a modification of the functioning of the solar cell by the optical excitation that also acts as a probe, pose unique challenges to the interpretation of the results using conventional models. Absorption of light in the visible range significantly increases when the NPI dye is in the activated state; however, the recombination rate also increases, thus limiting the efficiency. We identify and quantify the mechanism of enhanced recombination when the photochromic dye is activated using a combination of EIS and IMPS. From the comparison to a state-of-the-art reference dye (RK1), we were able to detect a new feature in the IMPS spectrum that is associated with the optical activation of the photochromic dye, providing a useful tool for assessing the electronic behavior of the device under different conditions of light excitation. This study provides guidelines to adequate characterization protocols of photochromic solar cells and essential insights on the interfacial electronic processes.