International Interlaboratory Comparison of Thermogravimetric Analysis of Graphene-Related Two-Dimensional Materials.

Research on graphene-related two-dimensional (2D) materials (GR2Ms) in recent years is strongly moving from academia to industrial sectors with many new developed products and devices on the market. Characterization and quality control of the GR2Ms and their properties are critical for growing industrial translation, which requires the development of appropriate and reliable analytical methods. These challenges are recognized by International Organization for Standardization (ISO 229) and International Electrotechnical Commission (IEC 113) committees to facilitate the development of these methods and standards which are currently in progress. Toward these efforts, the aim of this study was to perform an international interlaboratory comparison (ILC), conducted under Versailles Project on Advanced Materials and Standards (VAMAS) Technical Working Area (TWA) 41 "Graphene and Related 2D Materials" to evaluate the performance (reproducibility and confidence) of the thermogravimetric analysis (TGA) method as a potential new method for chemical characterization of GR2Ms. Three different types of representative and industrially manufactured GR2Ms samples, namely, pristine few-layer graphene (FLG), graphene oxide (GO), and reduced graphene oxide (rGO), were used and supplied to ILC participants to complete the study. The TGA method performance was evaluated by a series of measurements of selected parameters of the chemical and physical properties of these GR2Ms including the number of mass loss steps, thermal stability, temperature of maximum mass change rate (Tp) for each decomposition step, and the mass contents (%) of moisture, oxygen groups, carbon, and impurities (organic and non-combustible residue). TGA measurements determining these parameters were performed using the provided optimized TGA protocol on the same GR2Ms by 12 participants across academia, industry stakeholders, and national metrology institutes. This paper presents these results with corresponding statistical analysis showing low standard deviation and statistical conformity across all participants that confirm that the TGA method can be satisfactorily used for characterization of these parameters and the chemical characterization and quality control of GR2Ms. The common measurement uncertainty for each parameter, key contribution factors were identified with explanations and recommendations for their elimination and improvements toward their implementation for the development of the ISO/IEC standard for chemical characterization of GR2Ms.

New insights on energetic properties of graphene oxide (GO) materials and their safety and environmental risks.

Graphene oxide (GO) has been recognized as a thermally unstable and energetic material, but surprisingly its environmental and safety risks were not fully explored, defined, and regulated. In this study, systematic explosivity and flammability characterizations of commercial GO materials were conducted to evaluate the influence of key parameters such as physical forms (paste, powders, films, and aerogels), temperature, heating rate, mass, and heating environment, as well as their potential safety and environmental impacts. Results based on thermogravimetric analysis (TGA) showed that GO in paste and powder forms have lower temperature thresholds (>180-192 °C) to initiate micro-explosions compared to GO film and aerogels (> 205 °C and 213 °C) regardless of the environment (inert, air, or oxygen). The observed explosive behavior can be explained by thermal runaway reactions as a result of thermal deoxygenation and decomposition of oxygen functional groups. Flammability rating and limiting oxygen index (LOI) results confirmed that GO films are flammable materials that can spontaneously propagate flame in a low oxygen environment (~11 %). These results provided new insights about potential safety and environmental risks of GO materials, which somehow were not considered, suggesting urgent actions to improve current safety protocols for labeling, handling, transporting, and storage practices from manufacturers to the end-users.

Accounting Carbonaceous Counterfeits in Graphene Materials Using the Thermogravimetric Analysis (TGA) Approach.

Counterfeits in the supply chain of high-value advanced materials such as graphene and their derivatives have become a concerning problem with a potential negative impact on this growing and emerging industry. Recent studies have revealed alarming facts that a large percentage of manufactured graphene materials on market are not graphene, raising considerable concerns for the end users. The common and recommended methods for the characterization of graphene materials, such as transmission electron microscopy (TEM), atomic force microscopy (AFM), and Raman spectroscopy based on spot analysis and probing properties of individual graphene particles, are limited to provide the determination of the properties of "bulk" graphene powders at a large scale and the identification of non-graphene components or purposely included additives. These limitations are creating counterfeit opportunities by adding low-cost black carbonaceous materials into manufactured graphene powders. To address this problem, it is critical to have reliable characterization methods, which can probe the specific properties of graphene powders at bulk scale, confirm their typical graphene signature, and detect the presence of unwanted additional compounds, where the thermogravimetric analysis (TGA) method is one of the most promising methods to perform this challenging task. This paper presents the evaluation of the TGA method and its ability to detect low-cost carbon additives such as graphite, carbon black, biochar, and activated carbon as potential counterfeiting materials to graphene materials and their derivatives such as graphene oxide (GO) and reduced GO. The superior performance of the TGA method is demonstrated here, showing its excellent capability to successfully detect these additives when mixed with graphene materials, which is not possible by two other comparative methods (Raman spectroscopy and powder X-ray diffraction (XRD)), which are used as the common characterization methods for graphene materials.

Highly Water Dispersible Functionalized Graphene by Thermal Thiol-Ene Click Chemistry.

Functionalization of pristine graphene to achieve high water dispersibility remains as a key obstacle owing to the high hydrophobicity and absence of reactive functional groups on the graphene surface. Herein, a green and simple modification approach to prepare highly dispersible functionalized graphene via thermal thiol-ene click reaction was successfully demonstrated on pristine graphene. Specific chemical functionalities (-COO, -NH2 and -S) on the thiol precursor (L-cysteine ethyl ester) were clicked directly on the sp2 carbon of graphene framework with grafting density of 1 unit L-cysteine per 113 carbon atoms on graphene. This functionalized graphene was confirmed with high atomic content of S (4.79 at % S) as well as the presence of C-S-C and N-H species on the L-cysteine functionalized graphene (FG-CYS). Raman spectroscopy evidently corroborated the modification of graphene to FG-CYS with an increased intensity ratio of D and G band, ID/IG ratio (0.3 to 0.7), full-width at half-maximum of G band, FWHM [G] (20.3 to 35.5) and FWHM [2D] (64.8 to 90.1). The use of ethanol as the reaction solvent instead of common organic solvents minimizes the chemical hazards exposure to humans and the environment. This direct attachment of multifunctional groups on the surface of pristine graphene is highly demanded for graphene ink formulations, coatings, adsorbents, sensors and supercapacitor applications.

Graphene ink for 3D extrusion micro printing of chemo-resistive sensing devices for volatile organic compound detection.

Printed electronic sensors offer a breakthrough in the availability of low-cost sensor devices for improving the quality of human life. Conductive ink is the core of printing technology and also one of the fastest growing sector among all ink industries. Among many developed conductive inks, graphene-based inks are especially recognized as very promising for future fabrication of devices due to their low cost, unique properties, and compatibility with various platforms such as plastics, textiles, and paper. The development of graphene ink formulations for achieving high conductivity and high resolution printing is highly realized in 2D inkjet printing. Unfortunately, the ongoing development of graphene inks is possibly hampered by the non-uniform particle size and structures (e.g., different shapes and number of layers), which adversely affect printing resolution, conductivity, adhesion, and structural integrity. This study presents an environmentally sustainable route to produce graphene inks specifically designed for 3D extrusion-printing. The application of the prepared ink is demonstrated by mask-free automatic patterning of sensing devices for the detection of volatile organic compounds (VOCs). The sensing devices fabricated with this new ink display high-resolution patterning (average height/thickness of ∼12 µm) and a 10-fold improvement in the surface area/volume (SA/V) ratio compared to a conventional drop casting method. The extrusion printed sensors show enhanced sensing characteristics in terms of sensitivity and selectivity towards trace amount of VOC (e.g. 5 ppm ethanol) at room temperature (20 °C), which highlights that our method has highly promising potential in graphene printing technology for sensing applications.

Facile Multistep Synthesis of ZnO-Coated ß-NaYF4:Yb/Tm Upconversion Nanoparticles as an Antimicrobial Photodynamic Therapy for Persistent Staphylococcus aureus Small Colony Variants.

Antibacterial treatment strategies using functional nanomaterials, such as photodynamic therapy, are urgently required to combat persistent Staphylococcus aureus small colony variant (SCV) bacteria. Using a stepwise approach involving thermolysis to form ß-NaYF4:Yb/Tm upconversion nanoparticles (UCNPs) and surface ligand exchange with cetyltrimethylammonium bromide (CTAB), followed by zeolite imidazolate framework-8 (ZIF-8) coating and conversion to zinc oxide (ZnO), ß-NaYF4:Yb/Tm@ZnO nanoparticles were synthesized. The direct synthesis of ß-NaYF4:Yb/Tm@ZIF-8 UCNPs proved problematic due to the hydrophobic nature of the as-synthesized material, which was shown by zeta potential measurements using dynamic light scattering (DLS). To facilitate deposition of a ZnO coating, the zeta potentials of (i) as-synthesized UCNPs, (ii) calcined UCNPs, (iii) polyvinylpyrrolidone (PVP), and (iv) CTAB-coated UCNPs were measured, which revealed the CTAB-coated UCNPs to be the most hydrophilic and the better-dispersed form in water. ß-NaYF4:Yb/Tm@ZIF-8 composites formed using the CTAB-coated UCNPs were then converted into ß-NaYF4:Yb/Tm@ZnO nanoparticles by calcination under carefully controlled conditions. Photoluminescence analysis confirmed the upconversion process for the UCNP core, which allows the ß-NaYF4:Yb/Tm@ZnO nanoparticles to photogenerate reactive oxygen species (ROS) when activated by near-infrared (NIR) radiation. The NIR-activated UCNPs@ZnO nanoparticles demonstrated potent efficacy against both Staphylococcus aureus (WCH-SK2) and its associated SCV form (0.67 and 0.76 log colony forming unit (CFU) reduction, respectively), which was attributed to ROS generated from the NIR activated ß-NaYF4:Yb/Tm@ZnO nanoparticles.

Investigating the reinforcing mechanism and optimized dosage of pristine graphene for enhancing mechanical strengths of cementitious composites.

The proposed reinforcing mechanism and optimized dosage of pristine graphene (PRG) for enhancing mechanical, physicochemical and microstructural properties of cementitious mortar composites are presented. Five concentrations of PRG and two particle sizes are explored in this study. The results confirmed that the strength of the mortars depends on the dosage of PRG. The PRG sizes have a significant influence on the enhancement rate of mechanical strengths of the mortars, whereas they do not have a significant influence on the optimized PRG dosage for mechanical strengths. The PRG dosage of 0.07% is identified as the optimized content of PRG for enhancing mechanical strengths. The reinforcing mechanism of PRG for cement-based composites is mostly attributed to adhesion friction forces between PRG sheets and cementitious gels, which highly depends on the surface area of PRG sheets. The larger surface area of PRG sheets has a larger friction area associated with cementitious gels suggested to be one of favorable parameters for enhancing mechanical strengths with graphene additives.

Heat-induced conformational unfolding of fatty acid-free and fatted camel serum albumin: a comparative study.

Albumin is a multifunctional non-glycosylated, negatively charged plasma protein, with extraordinary ligand-binding and transport properties, antioxidant functions, and enzymatic activities. Physiologically, albumin transports free fatty acids in plasma and contributes in maintaining colloid osmotic pressure. Recent progresses in using albumin as a versatile protein carrier for drug targeting and for improving the pharmacokinetic profile of peptide or protein-based drugs, increased the attempts for improving albumin stability. Studying the thermal stability of camel albumin may provide us not only new clues for designing recombinant albumins, but also molecular insights on camel physiology. This study aims to determine the thermal stability of camel albumin. Fatted camel serum albumin (FCSA) was purified from blood via combination of Cohn's method and anion-exchange chromatography. Activated charcoal treatment was used to obtain defatted camel serum albumin (CSA). Fluorescence spectroscopy and differential scanning calorimetry (DSC) were used to study thermal denaturation of this protein. The set of fluorescence spectra were deconvoluted using the convex constraint analysis method (CCA). The results from deconvolution of fluorescence spectroscopy and DSC showed three and two components for CSA and FCSA, respectively. The bimodal DSC transition can be attributed to a crevice between domains I and II and formation of two independent thermodynamic domains. The crevice formation can be prevented by fatty acid binding between domains I and II. The calculated values of ∆H v/∆H cal, approximately 0.4 for CSA and near 1 for FCSA, confirmed the presence of at least one intermediate in thermal unfolding of CSA and the absence of the intermediate for FCSA. The obtained midpoint transition temperature (T m) of FCSA was about 20 °C higher than that of CSA. Such enormous stabilizing effect may be attributed to the fact that fatty acid serves as glue which preserves different domains beside each other and prevents formation of the mentioned intermediate.