Effect of brushing simulation on the wear behavior of repaired CAD-CAM restorations.

OBJECTIVE: The aim of the present study was to evaluate the influence of multidirectional brushing on the surface roughness, morphology, and bonding interface of resin-repaired CAD-CAM ceramic and composite restorations. MATERIALS AND METHODS: Twelve (N = 12) blocks (4 mm × 4 mm × 2 mm for parallel axis; 5 mm × 4 mm × 2 mm for perpendicular axis) of lithium disilicate glass-ceramic (IPS e.max CAD, Ivoclar AG) and CAD-CAM resin composite (Tetric CAD, Ivoclar AG) were obtained and repaired with direct resin composite (Clearfil AP-X, Kuraray). An abrasive slurry was prepared and the brushing was performed according to each restorative material and axis of brushing (n = 6; perpendicular to repair interface and parallel to repair interface) during 3,650 cycles (240 strokes per minute) to simulate 3 years of brushing. The surface roughness (Ra) and the profile variation for each material (restoration and direct repair resin composite) were measured at the baseline condition and after brushing, and the mean roughness and presence of steps at the repair interface were evaluated through factorial analysis of Variance (ANOVA). Scanning Electron Microscopy (SEM) images were taken to evaluate the surface topography of the repaired materials after brushing. RESULTS: The mean roughness of the repaired CAD-CAM restorations was affected by the brushing (P < .05), mainly when evaluating the repair material and the interface (P < .05), while the restorative CAD-CAM materials presented more stable values. The profile evaluation showed higher steps at the interface when repairing lithium disilicate than for CAD-CAM resin composite. CONCLUSION: Repaired CAD-CAM restorations were susceptible to wear after brushing simulation. The surface roughness of the direct resin composite was the most affected leading to step development at the interface, particularly in the repaired lithium disilicate samples. Cinical maintenance recalls and polishing protocols must be considered to enhance the longevity of such restorations.

Repair protocols for indirect monolithic restorations: a literature review.

Despite the advancements in indirect monolithic restorations, technical complications may occur during function. To overcome this issues, intraoral repair using resin composite is a practical and low-cost procedure, being able to increase the restoration's longevity. This review aimed to evaluate the need for repair and suggest a standardized repair protocol to the main indirect restorative materials. For this, studies were surveyed from PubMed with no language or date restriction, to investigate the scientific evidence of indirect monolithic restoration repair with direct resin composite. A classification to guide clinical decisions was made based on the FDI World Dental Federation criteria about defective indirect restorations considering esthetic and functional standards, along with the patient's view, to decide when polishing, repairing or replacing a defective restoration. Based on 38 surveyed studies, different resin composite intraoral repair protocols, that included mechanical and chemical aspects, were defined depending on the substrate considering resin-based, glass-ceramic or zirconia restorations. The presented criteria and protocols were developed to guide the clinician's decision-making process regarding defective indirect monolithic restorations, prolonging longevity and increasing clinical success.

Effect of Surface Treatment and Resin Cement on the Bond Strength of an Advanced Lithium Disilicate.

OBJECTIVES: The aim of the study was to evaluate the effect of surface treatment and resin cement on the bond strength of conventional and advanced lithium disilicates (ALDs). MATERIALS AND METHODS: Ceramic slices (2 × 13 × 15 mm) of conventional lithium disilicate (LD) (IPS e.max CAD) and ALD (CEREC Tessera) were sectioned, polished, and divided into 16 groups (n = 10) according to the factors: ceramic, surface treatment, and resin cement (Panavia V5 and Variolink Esthetic DC). Surface treatments consisted of hydrofluoric acid 4.9% etching for 20 seconds (Hf20) or 30 seconds (Hf30), self-etching ceramic primer (Se), and sandblasting (Sb). Then, a resin cement cylinder (Ø = 2.5 mm) was manufactured on each specimen's surface. The specimens were then submitted to a shear bond strength (SBS) test. Surface roughness was evaluated through a contact profilometer, and surface morphology was evaluated under scanning electron microscopy for qualitative analysis. STATISTICAL ANALYSIS: Two-way analysis of variance (ANOVA) was used to analyze the data of SBS and surface roughness. For bond strength, the effects of surface treatment, resin cement, and the interaction were analyzed for each ceramic. For roughness, analyzed factors include ceramic and surface treatment. RESULTS: ANOVA revealed that ceramic (p = 0.047) and surface treatment (p < 0.001) factors affected the bond strength, while the cements performed similarly. Both materials showed adequate bond strength (ALD 19.1 ± 7.7 MPa; LD 17.1 ± 7.9 MPa). Sb protocol showed the lowest mean value (9.6 ± 2.9 MPa) compared with Hf20 (22.0 ± 7.1 MPa), Hf30 (21.7 ± 7.4 MPa), and Se (19.3 ± 6.0 MPa). CONCLUSION: For both ceramics, the highest performance was obtained after applying Se and Hf20 or Hf30. Therefore, longer etching time is unnecessary. Sb protocol must be avoided.

Effect of printing layer orientation and polishing on the fatigue strength of 3D-printed dental zirconia.

OBJECTIVE: The aim of the study was to evaluate the influence of surface polishing and printing layer orientation on the fatigue behaviour of 3 mol% yttria-stabilized zirconia (3Y-TZP) by stereolithography (SLA) in comparison with subtractive manufacturing. MATERIALS AND METHODS: 60 experimental zirconia bar-shaped specimens were 3D-printed (P) via SLA, and 30 specimens were milled (M) from commercial zirconia block (Lava™ Frame, 3 M ESPE AG). All specimens had the same dimensions (1 mm × 1 mm x 12 mm) after sintering. The 3D-printed specimens were randomly divided according to printing orientations: parallel or perpendicular to the tensile surface in the fatigue test. The specimens were subsequently submitted to two surface finishing protocols (n = 15/gr): unpolished or polished. Their phase compositions were analysed by X-ray diffraction. The fatigue behaviour was evaluated by a stepwise approach. RESULTS: The milled and both 3D-printed groups showed similar phase compositions for the as-sintered condition. Considerable amounts of rhombohedral phase were detected after polishing. Milled unpolished samples presented significantly higher fatigue strength than 3D-printed unpolished samples. Polishing did not improve the fatigue strength for milled zirconia but was advantageous for the 3D-printed specimens. 3D-printed specimens with parallel printing-layer orientation were significantly stronger than specimens with perpendicular layers regardless of surface finishing. CONCLUSION: The manufacturing techniques had a significant influence on the fatigue strength of 3Y-TZP, but not on the phase compositions of the surface. The polishing protocol showed different effects on 3Y-TZP fatigue strength and induced phase transition of the 3Y-TZP from Tetragonal to Rhombohedral. The best fatigue strength was achieved through milling using an unpolished surface and SLA-printed layers that were parallel to the tensile surface, followed by polishing.

Mechanical Behavior of Repaired Monolithic Crowns: A 3D Finite Element Analysis.

This study evaluated the mechanical behavior and risk of failure of three CAD-CAM crowns repaired with different resin composites through a three-dimensional (3D) finite element analysis. Three-dimensional models of different cusp-repaired (conventional nanohybrid, bulk-fill, and flowable resin composites) crowns made of zirconia, lithium disilicate, and CAD-CAM resin composite were designed, fixed at the cervical level, and loaded in 100 N at the working cusps, including the repaired one. The models were analyzed to determine the Maximum Principal and Maximum Shear stresses (MPa). Complementary, an in vitro shear bond strength test (n = 10) was performed to calculate the risk of failure for each experimental group. The stress distribution among the models was similar when considering the same restorative material. The crown material affected the stress concentration, which was higher for the ceramic models (±9 MPa for shear stress; ±3 MPa for tensile stress) than for the CAD-CAM composite (±7 MPa for shear stress; ±2 MPa for tensile stress). The shear bond strength was higher for the repaired CAD-CAM resin composite (±17 MPa) when compared to the ceramics (below 12 MPa for all groups), while the repair materials showed similar behavior for each substrate. The stress distribution is more homogenous for repaired resin composite crowns, and a flowable direct resin composite seems suitable to repair ceramic crowns with less risk of failure.

Does glaze firing affect the strength of advanced lithium disilicate after simulated defects?

OBJECTIVE: To study the influence of glazing on strength repair of lithium disilicate glass-ceramics after defect incorporation in different production processing phases. MATERIALS AND METHODS: Bar-shaped specimens (1 × 1 × 12 mm, n = 280; 20/group) made from different lithium disilicate ceramics (IPS e.max CAD, Ivoclar, "LD" or advanced lithium disilicate CEREC Tessera, Dentsply Sirona, "ALD") were exposed to 7 different protocols: crystallized without (c) and with glaze layer (cg), with a defect incorporated before crystallization without (ic) and with glaze layer (icg), with a defect after crystallization without (ci) or with glaze layer (cig), and defect incorporated after the glaze layer (cgi). The flexural strength was determined using the three-point bending test. Analysis of indented areas and fractured specimens was performed by scanning electron microscopy. Flexural strength data were evaluated by two-way ANOVA followed by Tukey tests (α = 5%). RESULTS: Two-way ANOVA revealed a significant influence of ceramic (p < 0.001; F = 55.45), protocol (p < 0.001; F = 56.94), and the interaction protocol*ceramic (p < 0.001; F = 13.86). Regardless of ceramics, defect incorporation as final step resulted in the worst strength, while defects introduced before crystallization did not reduce strength. Glaze firing after defect incorporation led to strength repair for ALD, whereas such an effect was not evident for LD. CONCLUSIONS: The advanced lithium disilicate must receive a glaze layer to achieve its highest strength. Defects incorporated in the pre-crystallized stage can be healed during crystallization. Defects should not be incorporated after glazing. CLINICAL RELEVANCE: Clinical adjustments should be performed on pre-crystallized or crystalized restorations that receive a glazer layer afterwards.

Endocrown fixed partial denture: Is it possible?

STATEMENT OF PROBLEM: Whether the replacement of a missing tooth with a fixed partial denture supported by an endodontically treated abutment could be improved with endocrowns is unclear. PURPOSE: The purpose of the study was to evaluate the mechanical behavior of a fixed partial denture (FPD) according to the preparation of the abutment teeth (endocrown or complete crown) in terms of stress magnitude in the prosthesis, cement layer, and tooth. MATERIAL AND METHODS: A posterior model with 2 abutment teeth (first molar and first premolar) was modeled with a computer-aided design (CAD) software program for conducting a 3-dimensional finite element analysis (FEA). To replace the missing second premolar, the model was replicated in different possible FPDs according to the abutment preparation design (complete crown [Conventional], 2 endocrowns [EC]) or an endocrown on one of the abutment teeth (first molar [ECM] and first premolar [ECP]) for a total of 4 designs. All FPDs were in lithium disilicate. The solids were imported to an analysis software program (ANSYS 19.2) in the standard for the exchange of product data (STEP) format. The mechanical properties were considered isotropic and the materials to show linear elastic and homogeneous behavior. An axial load (300 N) was applied at the occlusal surface of the pontic. The results were evaluated by colorimetric stress maps of von Mises and maximum principal stress in the prosthesis, maximum principal stress and shear stresses on the cement layer, and maximum principal stress in the abutment teeth. RESULTS: The von Mises stresses revealed that all FPD designs behaved similarly and that, considering the maximum principal stress criteria, the pontic was the most stressed region. For the cement layer, the combined designs presented an intermediate behavior, with the ECM more suitable to reducing the stress peak. The conventional preparation allowed less stress concentration in both teeth, and higher stress concentration in the premolar was observed with an endocrown. The endocrown decreased the risk of fracture failure. Considering the risk of debonding failure for the prosthesis, the endocrown preparation was only able to decrease the failure risk when the EC design was used and when only the shear stress was considered. CONCLUSIONS: Performing endocrown preparations to retain a 3-unit lithium disilicate FPD is an alternative to conventional complete crown preparations.

The ability of mouthguards to protect veneered teeth: A 3D finite element analysis.

BACKGROUND/AIMS: Professional and amateur athletes might have veneer restorations. The aim of this study was to investigate the protective effect of mouthguards on veneered anterior restorations. METHODS: A nonlinear dynamic analysis was performed to simulate conditions during an impact with or without a custom-made mouthguard. Using a computer-aided design (CAD) software, a slice of a human maxilla was designed containing an upper right central incisor. The model was composed of mucosa, cortical bone, trabecular bone, periodontal ligament, dentin, enamel, and pulp tissue. The enamel was prepared (feather design), restored with an indirect veneer (1.0 mm thickness), and duplicated to simulate both conditions with or without a mouthguard (4 mm thickness). Both models were subdivided into finite elements using the computer-aided engineering (CAE) software. Frictionless contacts were used, and an impact was simulated in which a rigid sphere hit the model at 1 m s-1 . Fixation was defined at the base of the bone. The elastic modulus of the veneer was assessed by using five different restorative materials (resin composite, hybrid ceramic, zirconia-reinforced lithium silicate, lithium disilicate, and zirconia). Von Mises stress, minimal principal stress, and maximum principal stress (in MPa) were obtained and plotted for visual comparison. RESULTS: Von-Mises results showed higher stress concentrations in the veneer's cervical labial region for models without a mouthguard. Observing the quantitative results for each model, the highest compressive (709 MPa) and tensile (58 MPa) stresses occurred in the situation without a mouthguard with a zirconia veneer, while the lowest occurred in resin composite veneer with a mouthguard (8 and 5 MPa). The mouthguard was able to reduce the stresses in the tooth structure and it also reduced the risk of fracture in all conditions. CONCLUSIONS: Mouthguards were beneficial in reducing the effects of dental trauma regardless of the restorative material used to manufacture the indirect veneer, since they act by dampening the generated stresses during the trauma event. Equal impact stresses on a mouthguard will lead to higher stresses in veneered teeth with more rigid restorative materials leading to a less protective effect.

Nickel allergy is associated with a broad spectrum cytokine response.

BACKGROUND: Nickel-induced proliferation or cytokine release by peripheral blood mononuclear cells may be used for in vitro diagnosis of nickel allergy. OBJECTIVES: Aim of this study was to explore the nickel-specific cytokine profile to further elucidate the pathogenesis of nickel allergic contact dermatitis (ACD) and to identify potential new biomarkers for nickel ACD. METHODS: Peripheral blood mononuclear cells from patients and controls were cultured with T-cell skewing cytokine cocktails and/or nickel. Cytokine and chemokine concentrations were assessed in culture supernatants using validated multiplex assays. Specific cytokine production was related to history of nickel allergy and patch-test results. RESULTS: Twenty-one of the 33 analytes included in the analysis were associated with nickel allergy and included type1 (TNF-α, IFN-γ, TNF-ß), type 2 (IL-3, IL-4, IL-5, IL-13), type 1/2 (IL-2, IL-10), type 9 (IL-9), type 17/1 (IL-17A[F], GM-CSF, IL-21) and type 22 (IL-22) derived cytokines as well as the T-cell/antigen presentation cell derived factors Thymus and activation regulated chemokine (TARC), IL-27 and IP-10. Receiver operator characteristics (ROC) analysis showed that IL-5 was the strongest biomarker for nickel allergy. CONCLUSIONS: A broad spectrum of 33 cytokines and chemokines is involved in the allergen-specific immune response in nickel allergic patients. IL-5 remains, next to the lymphocyte proliferation test, the strongest biomarker for nickel allergy.

Biomechanics of implant-supported restorations / Biomecânica das restaurações implantossuportadas

The rehabilitation of patients with dental implant-supported restorations is an ideal treatment option in contemporary dentistry. The aim of this review was to compile and to demonstrate the mechanical response during loading condition, on the stress distributions of implant-supported prostheses. The findings show that the majority of stresses were concentrated in the cervical region of the implant/abutment interface and that they can be affected by several clinical parameters and loading conditions. Finally, the final prosthetic design should combine superior mechanical response, long-term survival rate and allow patient satisfaction. (AU)

A reabilitação de pacientes com restaurações implanto-suportadas é uma opção de tratamento ideal na odontologia contemporânea. O objetivo desta revisão foi compilar e demonstrar a resposta mecânica durante a aplicação de carga, na distribuição de tensão de próteses implanto-suportadas. Os achados mostram que a maioria das tensões se concentram na região cervical da interface implante/pilar e pode ser afetada por diversos parâmetros clínicos e condições de carregamento. Por fim, o desenho protético final deve combinar uma melhor resposta mecânica, taxa de sobrevida a longo prazo e permitir a satisfação do paciente. (AU)

Dental biomechanics of root-analog implants in different bone types.

STATEMENT OF PROBLEM: When implants are applied to restore oral function, the masticatory load on the crown will lead to stress development in all parts of the crown-abutment-implant-bone system. An optimal design of the whole system will be important for sustained function. PURPOSE: The purpose of this 3-dimensional (3D) finite element analysis (FEA) study was to evaluate the influence of the root-analog implant (RAI) design in molar rehabilitation and bone type. MATERIAL AND METHODS: Twelve 3D models of single posterior implant-supported restorations were created according to the zirconia implant design (monotype, 2-piece, or RAI) and bone type (D1, D2, D3, and D4, according to the Misch classification). The models were composed of cortical bone, cancellous bone, implant, cement layers, and a monolithic ceramic crown. For the 2-piece zirconia implant model, the titanium base, prosthetic screw, and framework were also designed. All materials were assumed to behave elastically throughout the entire analysis. The bone was fixed, and an axial loading of 600 N was applied to the contacts on the occlusal surface of the crowns. Results for the crown and implant were obtained in maximum principal stress, as well as the von Mises stress for the model and bone microstrain. RESULTS: High stress concentration was observed at the intaglio surface of the crowns near the loading region. Regardless of the design, the stress trend in the implant was similar, increasing proportionally to the bone type (D1>D2>D3>D4). RAI showed a homogeneous stress field near the values calculated for the conventional designs, but with lower magnitudes. The 2-piece zirconia model showed the highest stress magnitude regardless of the bone type and, therefore, the highest failure risk. All models showed a higher strain in the cortical bone than in the cancellous bone, located predominantly in the cervical region. A strain analysis showed that both conventional implant models presented similar behavior for D1 and D2 bone types, with an increasing difference for D3 and D4. RAI showed the lowest strain regardless of the bone type. CONCLUSIONS: Root-analog zirconia implants present a promising biomechanical behavior for dissipating the masticatory load in comparison with conventional screw-shaped implants.

Cytotoxicity and anti-biofilm properties of novel hybrid-glass-based caries infiltrant.

OBJECTIVES: To assess the cytotoxicity of an experimental hybrid-glass-based infiltrant and its effect on biofilm attachment, growth and metabolic activity, and to compare it to the resin-based infiltrant Icon. METHODS: Cytotoxicity of hybrid-glass-based material (EXP) and resin-based infiltrant Icon (Icon) was tested in direct contact tests on freshly cured (direct_mat) and on materials kept for 24 h in cell culture medium (direct_exmat), and extract test with materials 24-h extracts (extract). Cell viability of L929 mouse fibroblast cell line was measured with MTT assay, according to ISO10993-5:2009. Biofilm attachment (5 h), growth (24 h and 48 h) and lactic-acid production (24 h and 48 h) on glass-disk specimens coated with EXP or Icon, or uncoated (control), were assessed using a microcosm biofilm model and Amsterdam Active Attachment system. At indicated time points, biofilms were harvested, plated, and CFU counts were determined, while lactic-acid production was measured colorimetrically. RESULTS: Cell viability reduction by EXP was below 30%-threshold in direct contact tests, while in extract test an increased cell viability was observed. Icon reduced cell viability substantially in all three tests. Significantly less bacteria attached to the surface of EXP after 5 h compared to Icon and control. Biofilm growth was significantly lower on EXP than on Icon and control after 24 h, but this difference was smaller and statistically insignificant after 48 h. There was no difference in lactic-acid production among groups. SIGNIFICANCE: Novel hybrid-glass-based infiltrant seems to have a better biocompatibility and accumulates on its surface less bacteria than resin-based infiltrant, which makes it an attractive resin-free alternative.

Effect of hydrothermal aging on the microhardness of high- and low-viscosity conventional and additively manufactured polymers.

STATEMENT OF PROBLEM: Studies on the microhardness of novel additively manufactured polymers compared with well-established low- and high-viscosity composite resins with regard to chemical composition are lacking. PURPOSE: The purpose of this in vitro study was to evaluate the effect of hydrothermal aging on the microhardness of various conventional and additively manufactured polymers. MATERIAL AND METHODS: Cylindrically shaped specimens (N=240, n=10 per group) (Ø10×2 mm) were either additively manufactured (6 groups) or conventionally (6 groups) manufactured by using 3D (Optiprint Temp [OP; Dentona]; C&B MFH [ND; NextDent]; Saremco print CROWNTEC [SA; Saremco Dental AG]; Temp Print [TP; GC]; 3DELTA ETEMP [DM; Deltamed]; MED690 [ST; Stratasys, Ltd]) or conventional low (Gradia Direct [GR; GC]; Clearfil Majesty [CM; Kuraray Noritake]; Tetric EvoCeram [TE; Ivoclar AG]) and high (Gradia Direct Flo [GR-F; GC]; Clearfil Majesty Flow [CM-F; Kuraray Noritake]; Tetric EvoFlow [TE-F; Ivoclar AG]) viscous materials. All specimens were randomly allotted to 2 different aging methods (no-aging [dry] or aging by thermocycling [TC], ×6000, 5 °C-55 °C) and Vickers hardness (VH) tested (ZHV30; Zwick). Three indentations were made on each specimen (0.98-N load, duration 15 seconds). The calculated average microhardness value of each specimen was statistically analyzed by using 2-way ANOVA and Tukey post hoc tests (α=.05). Two-parameter Weibull distribution was calculated to predict the reliability of material type and aging method on VH. RESULTS: The mean ±standard deviation VH ranged between 17 ±0.5 VHN and 68 ±0.5 VHN in the following ascending order: group STa.05). The mean ±standard deviation of HV for aged (37 ±1 VHN) and nonaged (35 ±1 VHN) specimens were statistically similar (P>.05). The Weibull distribution values presented the highest shape for the aged group SA (37.81). CONCLUSIONS: The choice of the material had a significant effect and resulted in lower hardness for the 3-dimensionally printed materials than for the conventional composite resins. Under fatigue conditions, the choice of the material showed no significant difference when the Vickers microhardness was evaluated.

Effect of light-curing time and direction on microhardness of a light-cured resin composite to cement CAD-CAM restorations.

PURPOSE: To evaluate the effect of light-curing exposure time and location on polymerization of a restorative bulk-fill resin composite to lute endocrowns. METHODS: A light-cured restorative bulk-fill resin composite (Filtek One Bulk Fill) was submitted to direct light-curing by a high-power LED light-curing unit for 20 seconds as the positive control group (n= 10). Five more groups (n= 10) were light-cured in a natural tooth mold from two sites (labial and lingual) through a nanohybrid resin composite CAD-CAM restoration (Lava Ultimate A2 LT), for different irradiation times: 90 seconds per site, 40 seconds per site, 30 seconds per site, 20 seconds per site and 10 seconds per site. Vickers microhardness measurements were made at two different depths and test/control ratios were calculated. Ratios of 0.8 were considered as an adequate level of curing. A quantile regression was run to identify the minimally sufficient time of light-curing, and a two-way ANOVA was used to compare the results to previous findings and evaluate the effect of curing location. RESULTS: Analysis showed that 40 seconds x 2 is the minimal irradiation time that presents a test/control ratio above 0.8. Quantile regressions showed that the required irradiation time to reach a test/control ratio of 0.8 at a confidence level of 95% is 41.5 seconds and 39.2 seconds at 200 µm and 500 µm depths in the luting agent, respectively. There was no statistically significant difference between microhardness of the two depths except for the irradiation time of 10 seconds. The two-site to three-site light curing comparison showed no statistically significant difference except for the 90-second time. CLINICAL SIGNIFICANCE: Systematic light-curing through the labial, lingual and occlusal surfaces of thick indirect restorations is not always required for sufficient polymerization and can even waste valuable clinical time especially in the case of multiple restorations luted with resin composites.

Side effects of sodium lauryl sulfate applied in toothpastes: A scoping review.

PURPOSE: To perform a scoping review on the available literature regarding the side effects of sodium lauryl sulfate (SLS) used in toothpastes. METHODS: A scoping review was performed according to the PRISMA extension using PubMed. The electronic search was supplemented with a manual search for a complete overview. A customized data collection form was used to map data which was developed to register the extracted relevant data. The results of the selected articles were classified according to effects in the mouth, on the mucous membrane or elsewhere in the body and the healing effects of SLS-free toothpaste on aphthous ulcers. The outcomes from each category were reported in separate data forms and the studies with incomplete information were excluded from the assessment. RESULTS: Possible harmful effects of SLS were reported as mucosal desquamation, irritation or inflammation of oral mucosa or the dorsal part of the tongue, ulcerations, and toxic reactions in the oral cavity. CLINICAL SIGNIFICANCE: There is limited evidence that patients with recurrent aphthous ulcers can benefit from the use of SLS-free toothpastes in terms of decrease in the number of ulcerations, duration of the ulcerations and the intensity of the pain caused by the ulcerations. It is essential to create awareness for the side effects of SLS in toothpastes but further research is needed on its effect on oral and gastrointestinal systems when used in toothpastes.

Novel hybrid-glass-based material for infiltration of early caries lesions.

OBJECTIVES: To assess the effectiveness of two experimental, hybrid-glass-based infiltrants in arresting artificial white spot lesions (WSLs) in vitro, and to compare it with resin-based infiltrant Icon. METHODS: Artificial WSLs were formed on bovine enamel specimens (n = 68). Specimens were divided into four groups according to WSLs treatment: 1) no-treatment control (NTC), 2) infiltration with Icon (Icon), 3) infiltration with experimental hybrid-glass material (EXP), and 4) infiltration with experimental hybrid-glass material containing hydroxyapatite (HAp) nanoparticles (1%) (EXP-HAp). Half of the specimens from each group were subjected to cariogenic challenge using pH-cycling, consisting of a 7-day alternate incubation (37°C) in demineralization (4 h/day, pH=4.6) and remineralization solutions (20 h/day, pH=7.2). Another half of the specimens was incubated in distilled water (control). Caries progression was assessed by measuring surface micro-hardness (SMH), roughness (Ra) and average surface level, and by analyzing WSLs morphology. Non-cycled and pH-cycled specimens were compared with Man-Whitney U test, while different treatment groups were compared with Kruskal-Wallis test with pairwise comparisons (p < 0.05). RESULTS: In all groups (NTC, Icon and EXP-HAp) except EXP, SMH decreased significantly after pH cycling. In addition, SMH increased in EXP upon pH cycling and was significantly higher than in other pH-cycled groups (<0.001). Ra increased considerably, while surface level decreased after pH cycling in all groups except in EXP. Signs of demineralization and roughness increase in NTC, Icon and EXP-HAp were also observed with the SEM. SIGNIFICANCE: Experimental hybrid-glass-based material without HAp-nanoparticles could completely arrest the progression of WSLs, unlike its version with HAp-nanoparticles and resin-based infiltrant Icon.

Accuracy of a patient 3-dimensional virtual representation obtained from the superimposition of facial and intraoral scans guided by extraoral and intraoral scan body systems.

STATEMENT OF PROBLEM: A patient 3-dimensional virtual representation aims to facilitate the integration of facial references into treatment planning or prosthesis design procedures, but the accuracy of the virtual patient representation remains unclear. PURPOSE: The purpose of the present observational clinical study was to determine and compare the accuracy (trueness and precision) of a virtual patient obtained from the superimposition procedures of facial and intraoral digital scans guided by 2 scan body systems. MATERIAL AND METHODS: Ten participants were recruited. An intraoral digital scan was completed (TRIOS 4). Four fiduciary markers were placed in the glabella (Gb), left (IOL) and right infraorbital canal (IOR), and tip of the nose (TN). Two digitizing procedures were completed: cone beam computed tomography (CBCT) (i-CAT FLX V-Series) and facial scans (Face Camera Pro Bellus) with 2 different scan body systems: AFT (ScanBodyFace) and Sat 3D (Sat 3D). For the AFT system, a reference facial scan was obtained, followed by a facial scan with the participant in the same position as when capturing the CBCT scan. For the Sat 3D system, a reference facial scan was recorded, followed by a facial scan with the patient in the same position as when capturing the CBCT scan. The patient 3-dimensional representation for each scan body system was obtained by using a computer program (Matera 2.4). A total of 14 interlandmark distances were measured in the CBCT scan and both 3-dimensional patient representations. The discrepancies between the CBCT scan (considered the standard) and each 3-dimensional representation of each patient were used to analyze the data. The Kolmogorov-Smirnov test revealed that trueness and precision values were not normally distributed (P<.05). A log10 transformation was performed with 1-way repeated-measures MANOVA (α=.05). RESULTS: The accuracy of the virtual 3-dimensional patient representations obtained by using AFT and Sat 3D systems showed a trueness ranging from 0.50 to 1.64 mm and a precision ranging from 0.04 to 0.14 mm. The Wilks lambda detected an overall significant difference in the accuracy values between the AFT and Sat 3D systems (F=3628.041, df=14, P<.001). A significant difference was found in 12 of the 14 interlandmark measurements (P<.05). The AFT system presented significantly higher discrepancy values in Gb-IOL, TN-IOR, IOL-IOR, and TN-6 (P<.05) than in the Sat 3D system. The Sat 3D system had a significantly higher discrepancy in Gb-TN, TN-IOL, IOL-3, IOL-6, TN-8, TN-9, TN-11, IOR-11, and IOR-14 (P<.05) than in the AFT system. The Wilcoxon signed-rank test did not detect any significant difference in the precision values between the AFT and Sat 3D systems (Z=-0.838, P=.402). CONCLUSIONS: The accuracy of the patient 3-dimensional virtual representations obtained using AFT and Sat 3D systems showed trueness values ranging from 0.50 to 1.64 mm and precision values ranging from 0.04 to 0.14 mm. The AFT system obtained higher trueness than the Sat 3D system, but both systems showed similar precision values.

Patch test-relevant concentrations of metal salts cause localized cytotoxicity, including apoptosis, in skin ex vivo.

BACKGROUND: Metal alloys containing contact sensitizers (nickel, palladium, titanium) are extensively used in medical devices, in particular dentistry and orthopaedic surgery. The skin patch test is used to test for metal allergy. OBJECTIVE: To determine whether metal salts, when applied to freshly excised skin at patch test-relevant concentrations and using a method which mimics skin patch testing, cause in changes in the epidermis and dermis. METHODS: Tissue histology, apoptosis, metabolic activity, and inflammatory cytokine release were determined for two nickel salts, two palladium salts, and four titanium salts. RESULTS: Patch test-relevant concentrations of all metal salts caused localized cytotoxicity. This was observed as epidermis separation at the basement membrane zone, formation of vacuoles, apoptotic nuclei, decreased metabolic activity, and (pro)inflammatory cytokine release. Nickel(II) sulfate hexahydrate, nickel(II) chloride hexahydrate, titanium(IV) bis(ammonium lactato)dihydroxide, and calcium titanate were highly cytotoxic. Palladium(II) chloride, sodium tetrachloropalladate(II), titanium(IV) isopropoxide, and titanium(IV) dioxide showed mild cytotoxicity. CONCLUSION: The patch test in itself may be damaging to the skin of the patient being tested. These results need further verification with biopsies obtained during clinical patch testing. The future challenge is to remain above the elicitation threshold at noncytotoxic metal concentrations.

Fracture strength of non-invasively reinforced MOD cavities on endodontically treated teeth.

The purpose of this in-vitro study was to evaluate the fracture resistance and failure mode of non-invasively reinforced endodontically treated mandibular molars. Sixty freshly extracted defect-free mandibular molars were divided into four experimental groups with extensive MOD cavities on endodontically treated teeth with different restoration types and one control group with intact teeth (n = 12). The groups were as follows: "Normal": direct resin composite; "Ring": glass fiber-reinforced strip (Dentapreg) wrapped around buccal and lingual walls followed by direct resin composite; "Inlay": indirect CAD/CAM resin composite inlay; "Onlay": indirect CAD/CAM resin composite onlay; "Intact": Intact teeth (Control). Tetric EvoCeram and Adhese Universal (Ivoclar Vivadent) were used for direct restorations and Tetric CAD (Ivoclar Vivadent) adhesively luted with Adhese Universal and Variolink Esthetic LC (Ivoclar Vivadent) were used for indirect restorations. All teeth were submitted to thermo-mechanical cyclic loading. All samples were then submitted to a compressive load until fracture. Fracture load was noted and teeth were analyzed to classify the failure mode as either catastrophic (C) or non-catastrophic (NC). No statistically significant difference was found between fracture strength of the five groups when all specimens were considered (p = 0.1461). Intact group showed the lowest percentage of catastrophic failures (41.67%). Ring group presents less catastrophic failures (75%) than Normal group (83.34%), and failures of indirect restorations-Inlay and Onlay-were almost all catastrophic (91.67% and 100%, respectively).

Titanium salts tested in reconstructed human skin with integrated MUTZ-3-derived Langerhans cells show an irritant rather than a sensitizing potential.

BACKGROUND: The nature of clinically related adverse reactions to titanium is still unknown. OBJECTIVE: To determine whether titanium salts have irritant or sensitizing potential in a reconstructed human skin (RHS) model with integrated Langerhans cells (LCs). METHODS: RHS-LCs (ie, reconstructed epidermis) containing primary differentiated keratinocytes and CFSE+ CD1a+ -LCs generated from the MUTZ-3 cell line on a primary fibroblast-populated collagen hydrogel (dermis) were topically exposed to titanium(IV) bis(ammonium lactato)dihydroxide (TiALH). LC migration and plasticity were determined. RESULTS: TiALH resulted in CFSE+ CD1a+ -LC migration out of the epidermis. Neutralizing antibodies to CCL5 and CXCL12 showed that LC migration was CCL5 and not CXCL12 mediated. LCs accumulating within the dermis after TiALH exposure were CFSE+ Lang+ CD68+ which is characteristic of a phenotypic switch of MUTZ-LC to a macrophage-like cell. Furthermore, TiALH did not result in increased interleukin (IL)-1ß or CCR7 messenger RNA (mRNA) in the dermis, but did result in increased IL-10 mRNA. In addition, monocultures of MUTZ-LCs failed to increase LC maturation biomarkers CD83, CD86, and CXCL-8 when exposed to noncytotoxic concentrations of four different titanium salts. CONCLUSION: These results classify titanium salts as irritants rather than sensitizers and indicate that titanium implant-related complaints could be due to localized irritant-mediated inflammation arising from leachable agents rather than a titanium metal allergy.