AMnO3 (A = Sr, La, Ca, Y) Perovskite Oxides as Oxygen Reduction Electrocatalysts.

A series of perovskite-type manganites AMnO3 (A = Sr, La, Ca and Y) particles were investigated as electrocatalysts for the oxygen reduction reaction. AMnO3 materials were synthesized by means of an ionic-liquid method, yielding phase pure particles at different temperatures. Depending on the calcination temperature, particles with mean diameter between 20 and 150 nm were obtained. Bulk versus surface composition and structure are probed by X-ray photoelectron spectroscopy and extended X-ray absorption fine structure. Electrochemical studies were performed on composite carbon-oxide electrodes in alkaline environment. The electrocatalytic activity is discussed in terms of the effective Mn oxidation state, A:Mn particle surface ratio and the Mn-O distances.

Observation of antisite domain boundaries in Cu2ZnSnS4 by atomic-resolution transmission electron microscopy.

Atomic resolution transmission electron microscopy has been used to examine antisite defects in Cu2ZnSnS4 (CZTS) kesterite crystals grown by a hot injection method. High angle annular dark field (HAADF) imaging at sub-0.1 nm resolution, and lower magnification dark field imaging using reflections sensitive to cation ordering, are used to reveal antisite domain boundaries (ADBs). These boundaries, typically 5-20 nm apart, and extending distances of 100 nm or more into the crystals, lie on a variety of planes and have displacements of the type ½[110] or »[201], which translate Sn, Cu and Zn cations into antisite positions. It is shown that some ADBs describe a change in the local stoichiometry by removing planes of S and either Cu or Zn atoms, implying that these boundaries can be electrically charged. The observations also showed a marked increase in cation disorder in regions within 1-2 nm of the grain surfaces suggesting that growth of the ordered crystal takes place at the interface with a disordered shell. It is estimated that the ADBs contribute on average ∼0.1 antisite defect pairs per unit cell. Although this is up to an order of magnitude less than the highest antisite defect densities reported, the presence of high densities of ADBs that may be charged suggests these defects may have a significant influence on the efficiency of CZTS solar cells.

Over 75% incident-photon-to-current efficiency without solid electrodes.

The efficiency of photoelectrochemical reactions is conventionally defined in terms of the ratio between the current responses arising from the collection of carriers at electrical contacts and the incident photon flux at a given wavelength, i.e. the incident-photon-to-current-efficiency (IPCE). IPCE values are determined by a variety of factors such as the absorption constant of the active layer, bulk and surface recombination of photogenerated carriers, as well as their characteristic diffusion length. These parameters are particularly crucial in nanostructured photoelectrodes, which commonly display low carrier mobility. In this article, we examine the photoelectrochemical responses of a mesoporous TiO2 film in which the IPCE is enhanced by fast extraction of carriers via chemical reactions. TiO2 films are spontaneously formed by destabilisation of colloidal particles at the polarisable interface between two immiscible electrolyte solutions. The photocurrent arises from hole-transfer to redox species confined to the organic electrolyte, which is coupled to the transfer of electrons to oxygen in the aqueous electrolyte. The dynamic photocurrent responses demonstrate that no coupled ion transfer is involved in the process. The interplay of different interfacial length scales, molecularly sharp liquid/liquid boundary and mesoporous TiO2 film, promotes efficiencies above 75% (without correction for reflection losses). This is a significant step change in values reported for these interfaces (below 1%), which are usually limited to sub-monolayer coverage of photoactive molecular or nanoscopic materials.

Diamond-coated 'black silicon' as a promising material for high-surface-area electrochemical electrodes and antibacterial surfaces.

This report describes a method to fabricate high-surface-area boron-doped diamond (BDD) electrodes using so-called 'black silicon' (bSi) as a substrate. This is a synthetic nanostructured material that contains high-aspect-ratio nano-protrusions, such as spikes or needles, on the Si surface produced via plasma etching. We now show that coating a bSi surface composed of 15 µm-high needles conformably with BDD produces a robust electrochemical electrode with high sensitivity and high electroactive area. A clinically relevant demonstration of the efficacy of these electrodes is shown by measuring their sensitivity for detection of dopamine (DA) in the presence of an excess of uric acid (UA). Finally, the nanostructured surface of bSi has recently been found to generate a mechanical bactericidal effect, killing both Gram-negative and Gram-positive bacteria at high rates. We will show that BDD-coated bSi also acts as an effective antibacterial surface, with the added advantage that being diamond-coated it is far more robust and less likely to become damaged than Si.

Porous boron-doped diamond/carbon nanotube electrodes.

Nanostructuring boron-doped diamond (BDD) films increases their sensitivity and performance when used as electrodes in electrochemical environments. We have developed a method to produce such nanostructured, porous electrodes by depositing BDD thin film onto a densely packed "forest" of vertically aligned multiwalled carbon nanotubes (CNTs). The CNTs had previously been exposed to a suspension of nanodiamond in methanol causing them to clump together into "teepee" or "honeycomb" structures. These nanostructured CNT/BDD composite electrodes have been extensively characterized by scanning electron microscopy, Raman spectroscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. Not only do these electrodes possess the excellent, well-known characteristics associated with BDD (large potential window, chemical inertness, low background levels), but also they have electroactive areas and double-layer capacitance values ∼450 times greater than those for the equivalent flat BDD electrodes.

Charge transport across high surface area metal/diamond nanostructured composites.

High surface area composites featuring metal nanostructures and diamond particles have generated a lot of interest in the fields of heterogeneous catalysis, electrocatalysis, and sensors. Diamond surfaces provide a chemically robust framework for active nanostructures in comparison with sp(2) carbon supports. The present paper investigates the charge transport properties of high surface area films of high-pressure, high-temperature diamond particles in the presence and absence of metal nanostructures, employing electrochemical field-effect transistors. Oxygen- and hydrogen-terminated surfaces were generated on 500 nm diamond powders. Homogeneously distributed metal nanostructures, with metal volume fractions between ca. 5 and 20%, were either nucleated at the diamond particles by impregnation or incorporated from colloidal solution. Electrochemical field-effect transistor measurements, employing interdigitated electrodes, allowed the determination of composite conductivity as a function of electrode potential, as well as in air. In the absence of metal nanostructures, the lateral conductivity of the diamond assemblies in air is increased by over one order of magnitude upon hydrogenation of the particle surface. This observation is consistent with studies at diamond single crystals, although the somewhat modest change in conductivity suggests that charge transport is not only determined by the intrinsic surface conductivity of individual diamond particles but also by particle-to-particle charge transfer. Interestingly, the latter contribution effectively controls the assembly conductivity in the presence of an electrolyte solution as the difference between hydrogenated and oxygenated particles vanishes. The conductivity in the presence of metal nanoparticles is mainly determined by the metal volume fraction, while diamond surface termination and the presence of electrolyte solutions exert only minor effects. The experimental trends are discussed in terms of the electrochemical formation of charge carriers in the diamond particles, percolation theory, and charge screening at the double layer.