When solid recovered fuel (SRF) production and consumption maximize environmental benefits? A life cycle assessment.

Solid recovered fuel (SRF) from non-recyclable waste obtained from source separation and mechanical treatments can replace carbon coke in cement plants, contributing to the carbon neutrality. A life cycle assessment (LCA) of the SRF production from non-recyclable and selected waste was conducted in an Italian mechanical treatment plant to estimate the potential environmental impacts per ton of SRF produced. The analysis would contribute to evaluate the benefits that can be obtained due to coke substitution in best- and worst-case scenarios. The avoided impacts achieved were assessed, together with an evaluation of the variables that can affect the environmental benefits: SRF biogenic carbon content (in percentage of paper and cardboard); transportation distances travelled from the treatment plant to the cement kiln; the renewable energy used in the mechanical facility. On average, about 35.6 kgCO2-eq are generated by the SRF transportation and production phase. These impacts are greatly compensated by coke substitution, obtaining a net value of about -1.1 tCO2-eq avoided per ton of SRF. On balance, the global warming potential due to SRF production and consumption ranges from about -542 kgCO2-eq to about -1729 kgCO2-eq. The research recommended the use of SRF to substitute coke in cement kilns also in low densely-populated areas to mitigate environmental impacts and achieve carbon neutrality at a global level.

Social, economic and environmental benefits of organic waste home composting in Iran.

Organic waste management is challenging in low-middle income countries. Environmental impacts and high management costs affect the sustainable development of cities, an issue that is exacerbated by the lack of social involvement. The research conducted in Iran aims to assess the benefits of organic waste home composting in Shiraz to improve solid waste management (SWM) sustainability. The introduction of a pilot project to assess home composting systems was described, together with an economic, social and environmental analysis. The current SWM system (S0) has been compared with the new strategy proposed (S1), where home composting is considered to be introduced to collect about 10% of the municipal solid waste generated in a 10-year horizon. An economic balance related to the capital costs and operational costs of both systems was introduced, in parallel with a life cycle assessment (LCA) of the SWM system, and a questionnaire survey of the local population. Results showed that S1 leads to around 5% economic savings for the municipality due to the avoidance of organic waste transportation and disposal. Environmental benefits include a lowering of CO2-Eq emissions of about 19,076 tonnes year-1. In addition, about 28% of the interviewed (n = 319) agreed to employ the home composting system at home (CI 5.5%, 95% of confidence level) supporting the theory that about 10% of the organic waste can be segregated and home-composted. The research underlines that home composting can contribute to improve the sustainability of SWM systems in developing countries.

Social acceptance, emissions analysis and potential applications of paper-waste briquettes in Andean areas.

The research assessed waste-based briquettes consumption compared to conventional fuels in the Andes. Laboratory tests were conducted together with on-field analysis in Colquencha (Bolivia). The laboratory study shows that the performances of briquettes are better in terms of PM2.5 (933.4 ± 50.8 mg kg-1) and CO emissions (22.89 ± 2.40 g kg-1) compared to animal dung (6265.7 ± 1273.5 mgPM2.5 kg-1 and 48.10 ± 12.50 gCO kg-1), although the boiling time increased due to the lower fuel consumption rate and firepower compared to shrubs. The social survey organized with 150 Bolivian citizens suggested that low-income households are not able to pay for an alternative fuel: about 40% would pay less than 4 USD per month, while methane use for cooking is positively correlated with the income level (r = 0.244, p < 0.05). On field analysis suggested that local cookstoves are not appropriate for briquettes combustion since indoor air pollution overcomes 30 ppm of CO and 10 mgPM2.5 m-3. On balance, local small manufactures can be the main target for selling waste-based briquettes to reduce shrubs and wood consumption. However, briquettes production costs seem not yet competitive to natural easy-to-obtain fuels (i.e., animal dung). The research encourages the use of cellulosic and biomass waste-based briquettes in the Andean area for cooking, heating, or manufacturing and strongly advises policy-makers to introduce economic incentives for the recovery of secondary raw materials.

Environmental impact scenarios of organic fraction municipal solid waste treatment with Black Soldier Fly larvae based on a life cycle assessment.

Biowaste treatment with Black Soldier Fly (BSF) larvae is an alternative option for organic waste valorization. Its environmental impacts should be assessed and compared with conventional treatment options. The research aims to evaluate the treatment of organic fraction of municipal solid waste (OFMSW) with BSF larvae through a life cycle assessment (LCA). This study employed data inventories from literature and aimed to provide a wide range of production parameter values to identify the potentialities of BSF treatment in the best-case and worst-case scenarios. The SimaPro9, the database Ecoinvent3.5, and the impact assessment method IMPACT 2002+ have been employed for the analysis. A sensitivity analysis of relevant parameters was conducted, considering the avoided impacts that can be obtained thanks to the exploitation of larvae proteins for bioplastics or fishmeal production. Research findings highlight six main environmental impact indicators: respiratory inorganics (kg PM2.5-eq), ozone layer depletion (kg CFC-11-eq), terrestrial ecotoxicity (kg TEG soil), land occupation (m2 organic arable), global warming (kg CO2-eq), and non-renewable energy (MJ primary). The most relevant process generating impacts is BSF breeding, followed by boiling, storage, and OFMSW treatment. The environmental performance is better when the conventional fishmeal substituted, thanks to BSF larvae production, is made from areas 10,000 km far, implementing a 100% renewable energy scenario, reducing the energy consumption by 50%, increasing the lifespan of the equipment to 15 years, and products are employed locally. The current study represents the first attempt to evaluate the global higher or lower environmental impact scenario related to OFMSW treatment through BSF larvae.

A review of plastic waste circular actions in seven developing countries to achieve sustainable development goals.

Plastic waste circularity is a priority at a global level. Sustainable development goals (SDGs) set the ways to go, and the circular economy principles underlined the 'green' strategies to be employed. However, in practice, there is still much to do, especially in developing countries, where open burning and open dumping still represent the common way of plastic waste disposal. This review aims to analyse current plastic waste circular approaches in low-middle income settings. Seven countries were selected based on the economic level and data availability from the authors, and analysed to collect and critically discuss the actions implemented at a city level. Examples of waste minimization and recycling strategies, selective collection systems and public campaigns are reported from Africa, Asia and Latin America. First, a background analysis related to physical and governance aspects of municipal solid waste management systems of the chosen settings was conducted. The assessment was focused on the treatment processes or minimization actions. Then, the applicability of the projects to achieve the SDGs was commented on. The outcomes of the research underline the need to: (1) scale up small-scale and pilot projects, (2) disseminate good practices in more low- to middle-income settings, (3) create synergies among international partners for further replications in cities. Urgent solutions to plastic waste pollution are needed. The review presented practical actions to be implemented now to boost plastic waste circularity in developing cities.

Can tourism support resource circularity in small islands? On-field analysis and intervention proposals in Madagascar.

Open dumping and burning of solid waste are common practices in low-income countries. On small and touristic islands, the problem is exacerbated due to the additional volume of waste amount generated by tourists. This article presents how, using Nosy Be island in Madagascar as a case study, waste recovery and recycling can be fostered by tourism to tackle the waste challenge. About 95% of the waste of Nosy Be is openly dumped, discarded to sea or openly burned. Field analysis, interviews with local stakeholders and waste flow analysis served as methodological tools to assess the current solid waste management (SWM) system of Nosy Be. Stakeholder mapping and involvement as well as first exchange among local and international actors provided the basis to identify key practice and opportunities. Research findings highlight the importance of active participation and involvement of local partners supported by international experts, to suggest how touristic centres can serve as core of circular approaches. The article presents potential circular models to be implemented in Nosy Be, taking tourism as the entry point including the aspects of financial support, separated waste flows and the interest in 'green tourism marketing'. This case study underlines how international cooperation, touristic activities and common efforts can potentially help low-income communities improve their SWM practices.

Microbial Enzyme Biotechnology to Reach Plastic Waste Circularity: Current Status, Problems and Perspectives.

The accumulation of synthetic plastic waste in the environment has become a global concern. Microbial enzymes (purified or as whole-cell biocatalysts) represent emerging biotechnological tools for waste circularity; they can depolymerize materials into reusable building blocks, but their contribution must be considered within the context of present waste management practices. This review reports on the prospective of biotechnological tools for plastic bio-recycling within the framework of plastic waste management in Europe. Available biotechnology tools can support polyethylene terephthalate (PET) recycling. However, PET represents only ≈7% of unrecycled plastic waste. Polyurethanes, the principal unrecycled waste fraction, together with other thermosets and more recalcitrant thermoplastics (e.g., polyolefins) are the next plausible target for enzyme-based depolymerization, even if this process is currently effective only on ideal polyester-based polymers. To extend the contribution of biotechnology to plastic circularity, optimization of collection and sorting systems should be considered to feed chemoenzymatic technologies for the treatment of more recalcitrant and mixed polymers. In addition, new bio-based technologies with a lower environmental impact in comparison with the present approaches should be developed to depolymerize (available or new) plastic materials, that should be designed for the required durability and for being susceptible to the action of enzymes.

Organic waste valorization in remote islands: Analysis of economic and environmental benefits of onsite treatment options.

Solid waste management (SWM) represents an important issue for small islands. This research evaluates the municipal SWM system of the Pelagian archipelago, in Italy. The research aims to evaluate environmental and econoemic benefits of onsite treatment plants for the valorization of the organic fraction of municipal solid waste. The sizing of the anaerobic digestion (AD) and composting plant was developed, and the characteristics of the plant were used to conduct a cost analysis and an environmental life cycle assessment. The current waste management system (S0) has been compared with the new strategy proposed (S1). Results showed that S1 leads to save more than 250,000 € y-1 due to the avoidance of organic waste final disposal and shipping, determining a payback time of about 7 years. Environmental benefits include a lowering of CO2-eq emission of more than 1100 tonnes per year and a reduction of all the six environmental impacts analysed. The outcomes represent a novel contribution to the scientific literature since the research provides the first comparison of quantitative data about environmental and cost benefits of onsite AD plants in small islands. The research underlines that onsite waste treatment systems are viable options to improve SWM systems in isolated regions.

Construction and demolition waste recycling in developing cities: management and cost analysis.

In Bolivia, construction and demolition waste (CDW) is unmanaged. The current research implemented a CDW flow analysis and a cost assessment in the city of La Paz, aiming to compare future recycling scenarios. Lack of data is challenging; therefore, a review of 31 international studies has been conducted. Results report that the waste generation rate (WGR) of concrete residential buildings can be of about 91.9-113.3 kg m-2 for construction and about 867.2-1064.8 kg m-2 for demolition. In addition, positive correlation was found in national WGR with number of inhabitants and the GDP. By these results, it was estimated that about 271,051-349,418 tonnes of CDW are potentially generated yearly in La Paz, about two times more than the CDW projected by local authorities. By the scenarios analysis, it was estimated that 56.1-71.1% of the inert aggregates can be recycled. The cost of the system is estimated between 7.8 and 31.1 USD tCDW-1, for a total annual cost (20 years horizon) of about 2.3-9 million USD y-1 depending on the management scenario. In the best scenario, an average fee of less than 1% of the current costs of a flat in La Paz can be required, potentially affordable for the local economy. The most attractive scenario involves the source separation of recyclable materials and the hybrid organization of stationary and mobile recycling facilities. Results show that a CDW management can be implemented in La Paz to foster a circular economy in developing cities.

Comparison of environmental impacts related to municipal solid waste and construction and demolition waste management and recycling in a Latin American developing city.

Construction and demolition waste (CDW) and municipal solid waste (MSW) are the waste flows mostly generated at a global level. In developing countries, most of these waste streams are disposed of in open dumps. Policy-makers should be informed in which priorities should be established in order to improve the quality of the environment. The current research compares the environmental impacts generated by the MSW and CDW management system of La Paz (Bolivia). The aim is to evaluate (1) which environmental impact indicators are more important per waste flow and (2) if recycling can be considered a good option for mitigating such environmental footprint. A life cycle assessment (LCA) of the formal MSW management and the CDW mismanagement (i.e., open dumping) were conducted. The analysis of the management system (2019) is compared with future developments in recycling that counts with the support of an international cooperative project financed by the Italian cooperation. Results reported that, at a municipal level, CDW mismanagement contributes more than 60% to the freshwater aquatic ecotoxicity, which represents the most relevant impact generated by this waste stream. Recycling allows achieving avoided impacts higher than the ones produced for three of six environmental impacts, suggesting MSW and CDW recovery as an important option for preventing environmental degradation. The research is the first attempt to highlight the importance of organizing appropriate CDW management systems into an integrated waste management scheme for mitigating environmental impacts in developing cities.

Perspectives in solid recovered fuel production in Bolivia: Analysis of characteristics and potential benefits.

Solid recovered fuels (SRF) can provide another treatment option to the solid waste management (SWM) sector. However, in developing countries, to date, this system approach has not found considerable application. In Bolivia, SRF is not deemed within the national regulation and the final disposal in open dumping areas is still a reality. This research article provides the first attempt in evaluating the SRF characteristics and its potentialities in Bolivia, taking La Paz as a case study. Laboratory analysis of the rejects produced after selective collection and sorting has been conducted, focusing on non-hazardous and non-recyclable waste fractions. The international standards related to EN 15359:2011 for the classification of the SRF were employed, assessing the most feasible mix of materials to provide the highest classification of SRF in terms of low calorific value (LCV), chlorine, and mercury concentration. Results reported that the SRF made of 80% plastics (85% PE and 15% PP) and 20% cellulosic (blend 2), as well as 30% plastics (50% PP and 50% PE) and 70% cellulosic (blend 1), can be considered an alternative fuel in Bolivia. On balance, it has been estimated that the use of non-recyclable plastics and cardboard from municipal solid waste can provide, on average, about 0.9-2.7 billion MJ of energy for cement kilns, solving about 1.4-5.3% of the SWM issues and covering about 8-23.4% of the energy demand for cement production in Bolivia. These results are novel for the scientific literature for estimating the potentialities of SRF in Latin America.

Environmental assessment of construction and demolition waste recycling in Bolivia: Focus on transportation distances and selective collection rates.

Construction and demolition waste (CDW) management in developing countries is a global concern. The analysis of scenarios and the implementation of life cycle assessment (LCA) support decision-makers in introducing integrated CDW management systems. This paper introduces the application of an LCA in La Paz (Bolivia), where CDW is mainly dumped in open areas. The aim of the research is to evaluate the benefits of inert CDW recycling in function of the selective collection rate, defined as the amount of waste (%wt.) sorted at the source in relation to the total waste amount produced, and the distances from the CDW generation to the material recycling facility. The outcomes of the research suggest that increasing the selective collection rates (5% to 99%) spread the importance of transportation distances planning since it affects the magnitude of the environmental impacts (1.05 tCO2-eq to 20.7 tCO2-eq per km traveled). Transportation limits have been found to be lower than about 40 km in order to make recycling beneficial for all environmental impacts and for all selective collection rate, with the eutrophication potential as the limiting indicator. The theoretical analysis suggests implementing LCA with primary data and involving statistics related to the transportation of virgin materials avoided thanks to recycling. The outcomes of the research support the implementation of CDW recycling in developing countries since it has been found that material recovery is always beneficial.

Sensitivity analysis and improvements of the recycling rate in municipal solid waste life cycle assessment: Focus on a Latin American developing context.

The life cycle assessment (LCA) of municipal solid waste (MSW) systems in developing countries is a matter of research. Obtain reliable results is challenging since field data and local databases are not always available. The research presented in this paper explores this issue in La Paz (Bolivia), where six environmental impact categories were assessed. The LCA, related to the formal MSW management system of the city, involves a sensitivity analysis of ten parameters and the scenario assessment in relation to the increase of the recycling rate. Results report that the environmental impacts are mostly sensitive in relation to landfill gas collection efficiency, use of plastic bags, the transportation distances of collected waste, and the replacement rate of virgin materials. Global warming potential is the impact category most variable (341.38-551.95 kg CO2-eq tMSW-1), although it is not considerably reduced by recycling, which contributed mostly to the human toxicity and freshwater aquatic ecotoxicity. Doubling the amount of MSW recycled, from 235 t to about 473 t per year, human toxicity potential reduces of about 18% while freshwater aquatic ecotoxicity of about 12%. This research contributes for evaluating the most sensitive parameters in an MSW-LCA and to support policymakers towards waste recycling and sustainable development in Latin America developing cities.

Zooming on light packaging waste differences by scanning electron microscopy.

In the present paper, different types of pure and commercial plastic waste from different EU countries (UK, France, Italy, and Romania) were investigated for microstructure surface morphology and chemical properties by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDXS). The goal of the current investigation was to determine the chemical composition of selected packaging materials and compare these measurements with data obtained through a carbon-hydrogen-nitrogen-sulfur-oxygen (CHNS-O) elemental analyzer, which is conventionally used to characterize waste materials. The capabilities of the experimental approach are discussed in connection with their application to the study of waste sample materials and in comparison with alternative experimental methods such as elemental analysis. The CHNS-O comparison is made between the present data obtained with SEM-EDXS instrument and EA 3000 elemental analyzer used in previews studies conducted by the authors. Results show a difference of composition among packaging from different countries that can affect the treatment adopted for its valorization and the strategies of circular economy.

Formal and informal waste selective collection in developing megacities: Analysis of residents' involvement in Bolivia.

The implementation of waste selective collection (SC) schemes in low-income countries is a challenge although it is one important way for improving environmental sustainability. The inclusion of the population is necessary for gaining effective results, and social surveys are support methods for understanding citizens' involvement and behaviour. The aim of the research is to assess the support of the citizens concerning the formal and informal recycling in a low-middle income country. The study presents a questionnaire survey conducted in 2018 in La Paz, Bolivia, where 774 citizens were interviewed for evaluating their support to the formal and informal SC systems. Two questionnaires were submitted to two different users' categories: users of the formal recyclable waste gathering points; and citizens of the neighbourhoods. Evidence of the survey shows that about 8% of the population supports the formal SC while about 48% are used to selecting their waste at home. About 79.2% of them bring the waste to the informal recycling shops or provide it to waste pickers, throwing the waste into or nearby the mixed containers in order to facilitate their collection. This research demonstrates how social inclusion is important for planning recycling systems within a developing big city, starting from the SC. Results suggest that the informal sector can be an effective means for improving the recycling behaviour of the citizens. The study can be of interest to stakeholders involved in introducing recycling policies in developing cities where the SC rate is still low, and informal waste collection exists.

Application of a life cycle assessment for assessing municipal solid waste management systems in Bolivia in an international cooperative framework.

Using a life cycle assessment (LCA) to evaluate municipal solid waste management (MSWM) systems is strongly recommended and the approach has been used in high-income contexts. However, stakeholders in low to middle income countries are not aware of the potential of this approach, mainly due to a lack of financial resources and technical ability. The present work introduces a LCA of MSWM system scenarios into a developing city using an academic licence for the LCA software that is available for use exclusively by researchers. The MSWM system in place in 2018 in La Paz (Bolivia) was assessed according to seven scenarios. The novelty of the research is twofold: the use of LCA academic licensing in a low to middle income region where LCA is unknown as planning tool; and discussing the potential of the approach in conjunction with local and international stakeholders with a view to starting MSWM projects. The results of the analysis allow for the consideration of energy recovery and materials recycling as the main methods by which the environmental impact of MSW can be reduced, as has also been reported by other LCA studies conducted with full licensing of the relevant software. Moreover, the research is the basis for cooperative development projects that will adopt the LCA approach as the main assessment tool. The study discusses the importance of cooperation between universities and local governments for implementing new strategies for MSWM assessment and planning. The research is a contribution towards improving technical knowledge in developing countries for boosting sustainable development.

Selective collection of recyclable waste in Universities of low-middle income countries: Lessons learned in Bolivia.

The implementation of solid waste selective collection (SC) systems is quite difficult in low-middle income countries. Lack of awareness, infrastructure, administrative support and knowledge about recycling are the main barriers for its operation, reducing the possibility of successes. This paper introduces the methodological approach for assessing a recyclable waste SC project in a Bolivian public University. The waste fractions generated before (2016) and after (2019) the action were assessed, as well as the opinion and knowledge of the students, providing reliable indicators of the improvements and benefits obtained. Results of the waste characterization analysis reported that, after one month of implementation of the system, about 15 kg of plastic and 37.1 kg of paper and cardboard were collected, about 8 wt% and 42.9 wt% of the recyclable waste produced. At the same time, the questionnaire survey allows demonstrating that the SC behavior of the students improved considerably from 2018 to 2019, (t[608] = -7.654, p < 0.05***), as well as the satisfaction about the waste collection service provided (t[608] = -6.6224, p < 0.05***) and about the diffusion of information with awareness campaigns (t[608] = -8.708, p < 0.05***). The project and the phases followed for its implementation can be of reference for other local and international stakeholders, for replicating the study in other Universities and public areas. The novelty of the study is the introduction of a step by step methodology for assessing the SC of recyclable waste for supporting the recycling policies of developing cities in low-middle income countries and for boosting sustainable development according to the principle of the circular economy.

Application of healthcare waste indicators for assessing infectious waste management in Bolivia.

In the developing world, healthcare waste management is a human health and environmental burden that should be solved for improving sustainability. Solutions should be introduced in the short term, concerning management, planning, financial assistance and expertise. The paper introduces an indicator set for assessing healthcare waste management in developing cities, implemented in La Paz (Bolivia) as a case study. The objective is to suggest an integrated management tool as a first assessment technique to identify the prevailing problems with a healthcare waste management system. Results suggest that, in La Paz, the application of such indicators is useful for evaluating which priorities should be addressed for improving the healthcare waste management system. The tool was applied for introducing a study necessary for the application of new management plans, especially concerning healthcare waste treatment. The method can be replicated in other contexts worldwide, with a focus on the developing world, for comparing cities, management solutions and improvements carried out along the years. The approach is of interest for boosting sustainability and human health, improving the awareness of the actors and policy-makers involved in waste management.

Assessment of municipal solid waste selective collection scenarios with geographic information systems in Bolivia.

The analysis of municipal solid waste (MSW) selective collection (SC) scenarios is compulsory for planning future policies and actions towards circular economy. The use of geographic information system (GIS) is appropriated for obtaining reliable data about SC yields and management costs. However, in low-middle income countries, advanced assessments are difficult to introduce due to the lack of technical knowledge, financial support and the presence of the informal recycling sector. This research aims to assess the main potentialities of the introduction of SC systems in a Bolivian developing city taking into account the informal SC system in place. The study was conducted with QGIS3.8 software in order to evaluate the main advantages of the implementation of formal and informal recycling chains. Results reported that, comparing the implementation of formal SC of MSW with the scenario that considered the inclusion of the informal recycling, the activity of waste pickers allows reducing the expenses of about 10%, increasing the recycling rate of about 3.5%, and reducing the distances traveled with compactor trucks of about 7%. It means that, the annual path traveled by the collection trucks for gathering about 16,000ty-1, is reduced by 2734kmy-1, reducing the waste disposed to landfill of about 543.6ty-1 and the expenses of about €59,000 per year. The presentation of these results to policy-makers can support decision-making boosting the implementation of recycling activities including waste pickers. The study provided a contribution to the scientific literature assessing the main challenges and opportunities for implementing the circular economy in developing regions.