Influence of advanced wood-fired appliances for residential heating on indoor air quality.

This work was aimed at studying particulate matter (PM) in the indoor atmosphere of two flats where airtight biomass systems were used for domestic heating. PM10 and PM2.5 samples were collected by means of nine parallel sampling units, located in the outdoor and indoor areas of each flat. The samples were analyzed for PM macro-components (organic carbon, elemental carbon, macro-elements and inorganic ions) and for the soluble and residual fractions of micro-elements; the influence of the main PM sources on the indoor air quality was evaluated. The results confirm that infiltration from outdoor represents the main source of fine particles, while dust re-suspension, enhanced by the movements of the inhabitants, is one of the most important sources of coarse particles. Biomass-fueled heating systems are a significant source of indoor pollution, mainly due to the cleaning operations required for the removal of residual ash, which release particles in both the fine and the coarse size range. The impact of these operations resulted in indoor to outdoor ratios higher than one for most of the considered PM components. Very high amounts of copper and manganese, elements likely involved in the generation of oxidative stress, were released into the environment during ash removal from the pellet stove. Although this operation was very limited in time (about 15 min), the average concentration of Cu and Mn in PM10 and PM2.5 during the study period (18 days) was more than six times (Cu) and about twice (Mn) the concentration values measured outdoors.

Relationship between domestic smoking and metals and rare earth elements concentration in indoor PM2.5.

Cigarette smoke is the main source of indoor chemical and toxic elements. Cadmium (Cd), Thallium (Tl), Lead (Pb) and Antimony (Sb) are important contributors to smoke-related health risks. Data on the association between Rare Earth Elements (REE) Cerium (Ce) and Lanthanum (La) and domestic smoking are scanty. To evaluate the relationship between cigarette smoke, indoor levels of PM2.5 and heavy metals, 73 children were investigated by parental questionnaire and skin prick tests. The houses of residence of 41 "cases" and 32 "controls" (children with and without respiratory symptoms, respectively) were evaluated by 48-h PM2.5 indoor/outdoor monitoring. PM2.5 mass concentration was determined by gravimetry; the extracted and mineralized fractions of elements (As, Cd, Ce, La, Mn, Pb, Sb, Sr, Tl) were evaluated by ICP-MS. PM2.5 and Ce, La, Cd, and Tl indoor concentrations were higher in smoker dwellings. When corrected for confounding factors, PM2.5, Ce, La, Cd, and Tl were associated with more likely presence of respiratory symptoms in adolescents. We found that: i) indoor smoking is associated with increased levels of PM2.5, Ce, La, Cd, and Tl and ii) the latter with increased presence of respiratory symptoms in children.

Ultrasound plus low-level laser therapy for knee osteoarthritis rehabilitation: a randomized, placebo-controlled trial.

This study evaluated the synergistic effects of ultrasound (US) and low-level laser therapy (LLLT) with or without therapeutic exercises (TE) in women with knee osteoarthritis. Forty-two Caucasian women with knee osteoarthritis were allocated into three groups: (1) the placebo group who did not perform TE, but the prototype without emitting light or ultrasonic waves was applied, (2) the US + LLLT group in which only the prototype was applied and (3) the TE + US + LLLT group that performed TE before the prototype was applied. However, 35 women completed the full clinical trial. Pressure pain thresholds (PPT) using an algometer and functional performance during the sit-to-stand test were carried out. The average PPT levels increased for US + LLLT (41 ± 9 to 54 ± 15 N, p < 0.01) and TE + US + LLLT (32 ± 8 to 45 ± 9 N, p < 0.01) groups. The number of sit-to-stands was significantly higher for all groups. However, the change between pre-treatment and post-treatment (delta value) was greater for the US + LLLT (4 ± 1) and TE + US + LLLT groups (5 ± 1) than for the placebo group (2 ± 1) with a significant intergroup difference (p < 0.05). This study showed reduced pain and increased physical functionality after 3 months of US + LLLT with and without TE.

Multilayer Graphene/Carbon Black/Chlorine Isobutyl Isoprene Rubber Nanocomposites.

High loadings of carbon black (CB) are usually used to achieve the properties demanded of rubber compounds. In recent years, distinct nanoparticles have been investigated to replace CB in whole or in part, in order to reduce the necessary filler content or to improve performance. Multilayer graphene (MLG) is a nanoparticle made of just 10 graphene sheets and has recently become commercially available for mass-product nanocomposites. Three phr (part for hundred rubbers) of MLG are added to chlorine isobutyl isoprene rubber (CIIR)/CB composites in order to replace part of the CB. The incorporation of just 3 phr MLG triples the Young's modulus of CIIR; the same effect is obtained with 20 phr CB. The simultaneous presence of three MLG and CB also delivers remarkable properties, e.g. adding three MLG and 20 phr CB increased the hardness as much as adding 40 phr CB. A comprehensive study is presented, showing the influence on a variety of mechanical properties. The potential of the MLG/CB combination is illustrated to reduce the filler content or to boost performance, respectively. Apart from the remarkable mechanical properties, the CIIR/CB/MLG nanocomposites showed an increase in weathering resistance.