Electron Paramagnetic Resonance Characterization of Sodium- and Carbonate-Containing Hydroxyapatite Cement.

Ionizing radiation-induced paramagnetic defects in calcified tissues like tooth enamel are indicators of irradiation dose. Hydroxyapatite (HA), the principal constituent in these materials, incorporates a variety of anions (CO32-, F-, Cl-, and SiO44-) and cations (Mn2+, Li+, Cu2+, Fe3+, Mg2+, and Na+) that directly or indirectly contribute to the formation of stable paramagnetic centers upon irradiation. Here, we used an underexploited synthesis method based on the ambient temperature setting reaction of a self-hardening calcium phosphate cement (CPC) to create carbonate-containing hydroxyapatite (CHA) and investigate its paramagnetic properties following γ-irradiation. Powder X-ray diffraction and IR spectroscopic characterization of the hardened CHA samples indicate the formation of pure B-type CHA cement. CHA samples exposed to γ-radiation doses ranging from 1 Gy to 150 kGy exhibited an electron paramagnetic resonance (EPR) signal from an orthorhombic CO2•- free radical. At γ-radiation doses from 30 to 150 kGy, a second signal emerged that is assigned to the CO3•- free radical. We observed that the formation of this second species is dose-dependent, which provided a means to extend the useful dynamic range of irradiated CHA to doses >30 kGy. These results indicate that CHA synthesized via a CPC cement is a promising substrate for EPR-based dosimetry. Further studies on the CHA cement are underway to determine the suitability of these materials for a range of biological and industrial dosimetry applications.

Physicochemical, Mechanical, and Antimicrobial Properties of Novel Dental Polymers Containing Quaternary Ammonium and Trimethoxysilyl Functionalities.

The aims of this study were to evaluate the physicochemical and mechanical properties, antimicrobial (AM) functionality, and cytotoxic potential of novel dental polymers containing quaternary ammonium and trimethoxysilyl functionalities (e.g., N-(2-(methacryloyloxy)ethyl)-N,N-dimethyl-3-(trimethoxysilyl)propan-1-aminium iodide (AMsil1) and N-(2-(methacryloyloxy)ethyl)-N,N-dimethyl-11-(trimethoxysilyl)undecan-1-aminium bromide (AMsil2)). AMsil1 or AMsil2 were incorporated into light-cured (camphorquinone + ethyl-4-N,N-dimethylamino benzoate) urethane dimethacrylate (UDMA)/polyethylene glycol-extended UDMA/ethyl 2-(hydroxymethyl)acrylate (EHMA) resins (hereafter, UPE resin) at 10 or 20 mass %. Cytotoxic potential was assessed by measuring viability and metabolic activity of immortalized mouse connective tissue and human gingival fibroblasts in direct contact with monomers. AMsil-UPE resins were evaluated for wettability by contact angle measurements and degree of vinyl conversion (DVC) by near infra-red spectroscopy analyses. Mechanical property evaluations entailed flexural strength (FS) and elastic modulus (E) testing of copolymer specimens. The AM properties were assessed using Streptococcus mutans (planktonic and biofilm forms) and Porphyromonas gingivalis biofilm. Neither AMsil exhibited significant toxicity in direct contact with cells at biologically relevant concentrations. Addition of AMsils made the UPE resin more hydrophilic. DVC values for the AMsil-UPE copolymers were 2%-31% lower than that attained in the UPE resin control. The mechanical properties (FS and E) of AMsil-UPE specimens were reduced (11%-57%) compared to the control. Compared to UPE resin, AMsil1-UPE and AMsil2-UPE (10% mass) copolymers reduced S. mutans biofilm 4.7- and 1.7-fold, respectively (p ≤ 0.005). Although not statistically different, P. gingivalis biofilm biomass on AMsil1-UPE and AM AMsil2-UPE copolymer disks were lower (71% and 85%, respectively) than that observed with a commercial AM dental material. In conclusion, the AM function of new monomers is not inundated by their toxicity towards cells. Despite the reduction in mechanical properties of the AMsil-UPE copolymers, AMsil2 is a good candidate for incorporation into multifunctional composites due to the favorable overall hydrophilicity of the resins and the satisfactory DVC values attained upon light polymerization of AMsil-containing UDMA/PEG-U/EHMA copolymers.

Synthesis, Purification and Characterization of Polymerizable Multifunctional Quaternary Ammonium Compounds.

Methacrylate analogs of quaternary ammonium salts functionalized with carboxylic (AMadh1 68.8% yield, AMadh2 53.2% yield) and methoxysilane (AMsil1 94.8% yield, AMsil2 36.0% yield) groups were synthesized via Menschutkin reaction. Fourier-transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (1H, 13C and 2D 1H-13C heteronuclear single quantum coherence (HSQC) NMR), mass spectrometry, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were utilized to validate structures and characterize thermal properties of the novel multifunctional quaternary ammonium salts synthesized. The potential adhesive, coupling and antimicrobial properties of these multifunctional monomers encourage their further comprehensive evaluation in conventional and experimental copolymers and composites.

Antimicrobial Monomers for Polymeric Dental Restoratives: Cytotoxicity and Physicochemical Properties.

A trend for the next generation of polymeric dental restoratives is to incorporate multifunctional capabilities to regulate microbial growth and remineralize tooth surfaces. Polymerizable 2-(methacryloyloxy)-N-(2-(methacryloyloxy)ethyl)-N,N-dimethylethan-1-aminium bromide (IDMA1) and N,N'-([1,1'-biphenyl]-2,2'-diylbis(methylene))bis(2-(methacryloyloxy)-N,N-dimethylethan-1-aminium) bromide (IDMA2), intended for utilization in bi-functional antimicrobial and remineralizing composites, were synthesized, purified with an ethanol-diethyl ether-hexane solvent system, and validated by nuclear magnetic resonance (¹H and 13C NMR) spectroscopy, mass spectrometry, and Fourier-transform infrared spectroscopy. When incorporated into light-curable urethane dimethacrylate (UDMA)/polyethylene glycol-extended UDMA (PEG-U)/ethyl 2-(hydroxymethyl)acrylate (EHMA) (assigned UPE) resins, IDMAs did not affect the overall resins' hydrophilicity/hydrophobicity balance (water contact angle: 60.8-65.5°). The attained degrees of vinyl conversion (DVC) were consistently higher in both IDMA-containing copolymers and their amorphous calcium phosphate (ACP) composites (up to 5% and 20%, respectively) reaching 92.5% in IDMA2 formulations. Notably, these high DVCs values were attained without an excessive increase in polymerization stress. The observed reduction in biaxial flexure strength of UPE-IDMA ACP composites should not prevent further evaluation of these materials as multifunctional Class V restoratives. In direct contact with human gingival fibroblasts, at biologically relevant concentrations, IDMAs did not adversely affect cell viability or their metabolic activity. Ion release from the composites was indicative of their strong remineralization potential. The above, early-phase biocompatibility and physicochemical tests justify further evaluation of these experimental materials to identify formulation(s) suitable for clinical testing. Successful completion is expected to yield a new class of restoratives with well-controlled bio-function, which will physicochemically, mechanically, and biologically outperform the conventional Class V restoratives.

A New Bioactive Polylactide-based Composite with High Mechanical Strength.

A new bioresorbable polylactide/calcium phosphate composite with improved mechanical strengths and a more basic filler, tetracalcium phosphate (TTCP), was prepared by melt compounding. N-(2-aminoethyl)-3-aminoproplytrimethoxysilane (AEAPS) and pyromellitic dianhydride (PMDA) were used to improve the interfacial adhesion between TTCP and polylactide (PLA). While AEAPS improved the dispersion of TTCP in the matrix, PMDA might react with the terminal hydroxyl group of PLA and the amino group on the surface of AEAPS modified TTCP, which could further enhance the interfacial strength. The tensile strength was improved to 68.4 MPa for the PLA/TTCP-AEAPS composite from 51.5 MPa for the PLA/TTCP composite (20 wt% of TTCP). Dynamic mechanical analysis suggested that there was a 51 % improvement in storage modulus compared to that of PLA alone, when PMDA (0.2 wt% of PMDA) was incorporated into the PLA/TTCP-AEAPS composite (5 wt% of TTCP). Using this new bioresorbable PLA composite incorporated with a more basic filler for biomedical application, the inflammation and allergic effect resulted from the degraded acidic product are expected to be reduced.

Improve the Strength of PLA/HA Composite Through the Use of Surface Initiated Polymerization and Phosphonic Acid Coupling Agent.

Bioresorbable composite made from degradable polymers, e.g., polylactide (PLA), and bioactive calcium phosphates, e.g., hydroxyapatite (HA), are clinically desirable for bone fixation, repair and tissue engineering because they do not need to be removed by surgery after the bone heals. However, preparation of PLA/HA composite from non-modified HA usually results in mechanical strength reductions due to a weak interface between PLA and HA. In this study, a calcium-phosphate/phosphonate hybrid shell was developed to introduce a greater amount of reactive hydroxyl groups onto the HA particles. Then, PLA was successfully grafted on HA by surface-initiated polymerization through the non-ionic surface hydroxyl groups. Thermogravimetric analysis indiated that the amount of grafted PLA on HA can be up to 7 %, which is about 50 % greater than that from the literature. PLA grafted HA shows significantly different pH dependent ζ-potential and particle size profiles from those of uncoated HA. By combining the phosphonic acid coupling agent and surface initiated polymerization, PLA could directly link to HA through covalent bond so that the interfacial interaction in the PLA/HA composite can be significantly improved. The diametral tensile strength of PLA/HA composite prepared from PLA-grafted HA was found to be over twice that of the composite prepared from the non-modified HA. Moreover, the tensile strength of the improved composite was 23 % higher than that of PLA alone. By varying additional variables, this approach has the potential to produce bioresorbable composites with improved mechanical properties that are in the range of natural bones, and can have wide applications for bone fixation and repair in load-bearing areas.

Preparation and Properties of Nanoparticles of Calcium Phosphates With Various Ca/P Ratios.

This study aimed at preparing and studying the properties of nanoparticles of calcium phosphate (nCaP) with Ca/P ratios ranging from 1.0 to 1.67 using a spray-drying technique. Micro-structural analyses suggested that the nCaPs with Ca/P ratios of 1.67 to 1.33 were nano-sized amorphous calcium phosphate (ACP) containing varying amounts of acid phosphate and carbonate. The nCaP with Ca/P ratio of 1 contained only nano-sized low crystalline dicalcium phosphate (DCP). BET measurements of the nCaPs showed specific surface areas of (12 ± 2 to 50 ± 1) m(2)/g, corresponding to estimated equivalent spherical diameters of (38 to 172) nm. However, dynamic light scattering measurements revealed much larger particles of (380 ± 49 to 768 ± 111) nm, owing to agglomeration of the smaller primary nano particles as revealed by Scanning Electron Microscopy (SEM). Thermodynamic solubility measurements showed that the nCaPs with Ca/P ratio of 1.33 - 1.67 all have similar solubility behavior. The materials were more soluble than the crystalline hydroxyapatite (HA) at pH greater than about 4.7, and more soluble than ß-tricalcium phosphate (ß-TCP), octacalcium phosphate (OCP) and DCP at pH above 5.5. Their solubility approached that of α-tricalcium phosphate (α-TCP) at about pH 7. These nCaPs, which cannot be readily prepared by other currently available methods for nanoparticle preparation, have potential biomedical applications.

Hydrolysis of tetracalcium phosphate under a near-constant-composition condition--effects of pH and particle size.

Tetracalcium phosphate (TTCP) is a component of a number of calcium phosphate cements used clinically for bone defect repairs. The strength, phase composition, and solubility of the set cement are highly dependent on the reactions of the cement components during setting. This study investigated hydrolysis reactions of TTCP under solution compositions chosen to mimic the compositions of the cement liquid during setting. The study utilized a pseudo-constant-composition technique that allowed both the rate and stoichiometry of the reaction to be determined while the reaction proceeded under a specific, constantly held solution pH, thereby keeping a constant calcium-to-phosphate ratio in solution. The hydrolysis experiments were conducted using either a fine (median particle size 3.5 microm) or coarse (median particle size 13.2 microm) TTCP powder at pH 7, 8 and 10. Low crystalline calcium (Ca)-deficient hydroxyapatite (HA) was the product in all experiments. Both the solution pH and TTCP particle size produced significant effects on all aspects of the hydrolysis reaction. At a given pH, the fine TTCP produced a HA product with a greater Ca deficiency than did the coarse TTCP. For a given particle size, the Ca deficiency generally decreased with increasing pH. Hydrolysis reaction rate generally decreased with increasing pH or TTCP particle size. At pH 7 and 8, the solution was undersaturated with respect to TTCP and supersaturated with respect to HA, suggesting that the reaction rate was limited by TTCP dissolution. In contrast, at pH 10, the solution was approximately saturated with respect to TTCP and highly supersaturated with respect to HA, suggesting that HA formation was the rate-determining step of the reaction. The findings provided useful insights into the setting reaction mechanisms of TTCP-containing calcium phosphate cements.