Enhancement of properties of a cell-laden GelMA hydrogel-based bioink via calcium phosphate phase transition.

To improve the properties of the hydrogel-based bioinks, a calcium phosphate phase transition was applied, and the products were examined. We successfully enhanced the mechanical properties of the hydrogels by adding small amounts (< 0.5 wt%) of alpha-tricalcium phosphate (α-TCP) to photo-crosslinkable gelatin methacrylate (GelMA). As a result of the hydrolyzing calcium phosphate phase transition involvingα-TCP, which proceeded for 36 h in the cell culture medium, calcium-deficient hydroxyapatite was produced. Approximately 18 times the compressive modulus was achieved for GelMA with 0.5 wt%α-TCP (20.96 kPa) compared with pure GelMA (1.18 kPa). Although cell proliferation decreased during the early stages of cultivation, both osteogenic differentiation and mineralization activities increased dramatically when the calcium phosphate phase transition was performed with 0.25 wt%α-TCP. The addition ofα-TCP improved the printability and fidelity of GelMA, as well as the structural stability and compressive modulus (approximately six times higher) after three weeks of culturing. Therefore, we anticipate that the application of calcium phosphate phase transition to hydrogels may have the potential for hard tissue regeneration.

142Development of an alginate-gelatin bioink enhancing osteogenic differentiation by gelatin release.

Hydrogels are natural bioink options for cellular printing due to their high-water content and permeable three-dimensional (3D) polymeric structure, which are favorable for cellular anchoring and metabolic activities. To increase the functionality of hydrogels as bioinks, biomimetic components are often incorporated, such as proteins, peptides, and growth factors. In this study, we aimed to enhance the osteogenic activity of a hydrogel formulation by integrating both the release and retention of gelatin so that gelatin serves as both an indirect support for released ink component on cells nearby and a direct support for encapsulated cells inside a printed hydrogel, thereby fulfills two functions. Methacrylate-modified alginate (MA-alginate) was chosen as the matrix because it has a low cell adhesion effect due to the absence of ligands. The gelatin-containing MA-alginate hydrogel was fabricated, and gelatin was found to remain in the hydrogel for up to 21 days. The gelatin remaining in the hydrogel had positive effects on encapsulated cells, especially on cell proliferation and osteogenic differentiation. The gelatin released from the hydrogel affected the external cells, showing more favorable osteogenic behavior than the control sample. It was also found that the MA-alginate/gelatin hydrogel could be used as a bioink for printing with high cell viability. Therefore, we anticipate that the alginate-based bioink developed in this study could potentially be used to induce osteogenesis in bone tissue regeneration.

Fabrication of color-graded feldspathic dental prosthetics for aesthetic and restorative dentistry.

OBJECTIVE: Feasibility investigation of natural teeth shades replication on dental prosthetics fabricated via functionally graded additive manufacturing (FGAM) using combination of feldspathic porcelain (FP) and yttrium aluminum garnet cerium (Y3Al5O12:Ce, YAG:Ce) as a promising esthetic restoration option. METHODS: Color-graded feldspathic crown fabrication parameter through FGAM method was comprehensively examined from the slurry rheology, cure depth, debinding to sintering temperature. Effect of light absorbent also checked towards overcuring reaction during UV exposure by the shape comparison. Lastly, the flexural bending strength measured following ISO 6872:2015 to assure the applicability. Applying the studied parameter, natural teeth shades then imitated and investigated by alteration of FP and FP + 0.1 wt% YAG:Ce (Y-FP). Generated color across the structure captured through mobile camera, interpreted through the CIELAB coordinate and the gradation confirmed by the color differences (ΔE00) calculated using CIEDE2000 formula. RESULT: Parameter study indicated that 70 wt% of FP slurry with 3 wt% dispersant and 0.2 wt% light absorbent is favored. It produces excellent flowability in our FGAM system with less overcuring justified by edge margin reduction from 95.65° to 90.00° after UV exposure on rectangle shapes masking. The obtain structure also offers adequate flexural bending strength of 106.26 MPa (FP) and 101.36 MPa (Y-FP) after sintering at 780 °C. This validated the materials as class 2 dental prosthetics citing ISO 6872:2015. Color gradation was verified by the yellow b* value reduction (14.8 to -3.33) as it shifted from cervical to incisal area while ΔE00 further affirmed the differences from each segment in comparison with the FP and Y-FP. SIGNIFICANCE: Color gradation was successfully replicated by FP and YAG:Ce composition shift via FGAM technique. This result highlights the potential of FGAM as an alternative for fabricating dental prosthetics with high efficiency and improved esthetic appeal.

Support-less ceramic 3D printing of bioceramic structures using a hydrogel bath.

Volumetric bone tissue defects are beyond the intrinsic regenerative capacity of bone tissue. With the recent development of ceramic 3D printing, various bioceramic scaffolds that can induce bone regeneration are being actively developed. However, hierarchical bone is complex, with overhanging structures that require additional sacrificial support during ceramic 3D printing. Not only can this increase the overall process time and material consumption, but breaks and cracks may occur when sacrificial supports are removed from fabricated ceramic structures. In this study, a support-less ceramic printing (SLCP) process using a hydrogel bath was developed to facilitate the manufacture of complex bone substitutes. A hydrogel bath, consisting of pluronic P123 with temperature-sensitive properties, mechanically supported the fabricated structure when the bioceramic ink was extruded into the bath and promoted the cement reaction to cure the bioceramic. SLCP enables the fabrication of complex bone constructs with overhanging structures, such as the mandible and maxillofacial bones, with reduced overall processing time and material consumption. Scaffolds fabricated by SLCP showed more cell adhesion, higher cell growth rate, and osteogenic protein expression due to their rougher surface than conventionally printed scaffolds. Hybrid scaffolds were fabricated by SLCP to co-print cells and bioceramics, and SLCP provided a cell-friendly environment, exhibiting high cell viability. SLCP enables control of the shape of various cells, bioactive substances, and bioceramics and thus can be used as an innovative 3D bioprinting technique to manufacture complex hierarchical bone structures.