Matrix stiffening and ß1 integrin drive subtype-specific fibroblast accumulation in lung cancer.

UNLABELLED: The crucial role of tumor-associated fibroblasts (TAF) in cancer progression is now clear in non-small cell lung cancer (NSCLC). However, therapies against TAFs are limited due to a lack of understanding in the subtype-specific mechanisms underlying their accumulation. Here, the mechanical (i.e., matrix rigidity) and soluble mitogenic cues that drive the accumulation of TAFs from major NSCLC subtypes: adenocarcinoma (ADC) and squamous cell carcinoma (SCC) were dissected. Fibroblasts were cultured on substrata engineered to exhibit normal- or tumor-like stiffnesses at different serum concentrations, and critical regulatory processes were elucidated. In control fibroblasts from nonmalignant tissue, matrix stiffening alone increased fibroblast accumulation, and this mechanical effect was dominant or comparable with that of soluble growth factors up to 0.5% serum. The stimulatory cues of matrix rigidity were driven by ß1 integrin mechano-sensing through FAK (pY397), and were associated with a posttranscriptionally driven rise in ß1 integrin expression. The latter mechano-regulatory circuit was also observed in TAFs but in a subtype-specific fashion, because SCC-TAFs exhibited higher FAK (pY397), ß1 expression, and ERK1/2 (pT202/Y204) than ADC-TAFs. Moreover, matrix stiffening induced a larger TAF accumulation in SCC-TAFs (>50%) compared with ADC-TAFs (10%-20%). In contrast, SCC-TAFs were largely serum desensitized, whereas ADC-TAFs responded to high serum concentration only. These findings provide the first evidence of subtype-specific regulation of NSCLC-TAF accumulation. Furthermore, these data support that therapies aiming to restore normal lung elasticity and/or ß1 integrin-dependent mechano regulation may be effective against SCC-TAFs, whereas inhibiting stromal growth factor signaling may be effective against ADC-TAFs. IMPLICATIONS: This study reveals distinct mechanisms underlying the abnormal accumulation of tumor-supporting fibroblasts in two major subtypes of lung cancer, which will assist the development of personalized therapies against these cells.

A spectrophotometer-based diffusivity assay reveals that diffusion hindrance of small molecules in extracellular matrix gels used in 3D cultures is dominated by viscous effects.

The design of 3D culture studies remains challenging due to the limited understanding of extracellular matrix (ECM)-dependent hindered diffusion and the lack of simple diffusivity assays. To address these limitations, we set up a cost-effective diffusivity assay based on a Transwell plate and the spectrophotometer of a Microplate Reader, which are readily accessible to cell biology groups. The spectrophotometer-based assay was used to assess the apparent diffusivity D of FITC-dextrans with molecular weight (4-70kDa) spanning the physiological range of signaling factors in a panel of acellular ECM gels including Matrigel, fibrin and type I collagen. Despite their technical differences, D data exhibited ∼15% relative difference with respect to FRAP measurements. Our results revealed that diffusion hindrance of small particles is controlled by the enhanced viscosity of the ECM gel in conformance with the Stokes-Einstein equation rather than by geometrical factors. Moreover, we provided a strong rationale that the enhanced ECM viscosity is largely contributed to by unassembled ECM macromolecules. We also reported that gels with the lowest D exhibited diffusion hindrance closest to the large physiologic hindrance of brain tissue, which has a typical pore size much smaller than ECM gels. Conversely, sparse gels (≤1mg/ml), which are extensively used in 3D cultures, failed to reproduce the hindered diffusion of tissues, thereby supporting that dense (but not sparse) ECM gels are suitable tissue surrogates in terms of macromolecular transport. Finally, the consequences of reduced diffusivity in terms of optimizing the design of 3D culture experiments were addressed in detail.

Oxygen diffusion and consumption in extracellular matrix gels: implications for designing three-dimensional cultures.

Three-dimensional (3D) cultures are increasingly used as tissue surrogates to study many physiopathological processes. However, to what extent current 3D culture protocols provide physiologic oxygen tension conditions remains ill defined. To address this limitation, oxygen tension was measured in a panel of acellular or cellularized extracellular matrix (ECM) gels with A549 cells, and analyzed in terms of oxygen diffusion and consumption. Gels included reconstituted basement membrane, fibrin and collagen. Oxygen diffusivity in acellular gels was up to 40% smaller than that of water, and the lower values were observed in the denser gels. In 3D cultures, physiologic oxygen tension was achieved after 2 days in dense (≥3 mg/mL) but not sparse gels, revealing that the latter gels are not suitable tissue surrogates in terms of oxygen distribution. In dense gels, we observed a dominant effect of ECM composition over density in oxygen consumption. All diffusion and consumption data were used in a simple model to estimate ranges for gel thickness, seeding density and time-window that may support physiologic oxygen tension. Thus, we identified critical variables for oxygen tension in ECM gels, and introduced a model to assess initial values of these variables, which may short-cut the optimization step of 3D culture studies.

Collective epithelial cell invasion overcomes mechanical barriers of collagenous extracellular matrix by a narrow tube-like geometry and MMP14-dependent local softening.

Collective cell invasion (CCI) through interstitial collagenous extracellular matrix (ECM) is crucial to the initial stages of branching morphogenesis, and a hallmark of tissue repair and dissemination of certain tumors. The collagenous ECM acts as a mechanical barrier against CCI. However, the physical nature of this barrier and how it is overcome by cells remains incompletely understood. To address these questions, we performed theoretical and experimental analysis of mammary epithelial branching morphogenesis in 3D type I collagen (collagen-I) gels. We found that the mechanical resistance of collagen-I is largely due to its elastic rather than its viscous properties. We also identified two strategies utilized by mammary epithelial cells that can independently minimize ECM mechanical resistance during CCI. First, cells adopt a narrow tube-like geometry during invasion, which minimizes the elastic opposition from the ECM as revealed by theoretical modeling of the most frequent invasive shapes and sizes. Second, the stiffness of the collagenous ECM is reduced at invasive fronts due to its degradation by matrix metalloproteinases (MMPs), as indicated by direct measurements of collagen-I microelasticity by atomic force microscopy. Molecular techniques further specified that the membrane-bound MMP14 mediates degradation of collagen-I at invasive fronts. Thus, our findings reveal that MMP14 is necessary to efficiently reduce the physical restraints imposed by collagen-I during branching morphogenesis, and help our overall understanding of how forces are balanced between cells and their surrounding ECM to maintain collective geometry and mechanical stability during CCI.