Soldering in Dentistry: An Updated Technical Review.

INTRODUCTION: The need to permanently join two or more pieces of metal using heat is a frequent condition in various fields of medicine such as dentistry. Welding, brazing and soldering are permanent joining techniques between different metals that require in-depth background knowledge in order to obtain predictable results. AIM: This review examines the different methods of joining metals using heat and their fields of application. DISCUSSION: It is possible to create permanent metal joints in various phases of the creation of final products that will be used on the patient. In several cases, welds are also made directly by the manufacturer during industrial processing. In dentistry, dental laboratories perform complex welds mainly on dental prostheses and orthodontic appliances during the production process. It is also possible to obtain intraoral welding carried out by the clinician inside the patient's oral cavity. Welding can be carried out using combustible gases, electric current, infrared light and laser light through different technical procedures which must be chosen according to the specific needs and the metals to be joined. CONCLUSIONS: It is useful for the dentist and dental technician to know the different welding methods, including those carried out in the factory by the manufacturer, to better understand the physical properties and mechanical resistance of the components marketed for the construction of prostheses and orthodontic appliances. The enormous variety of conditions in which those who practice welding can find themselves therefore presupposes in-depth knowledge in this field in order to apply the most suitable technique.

Filter Masks during the Second Phase of SARS-CoV-2: Study on Population.

During the SARS-CoV-2 pandemic, the most common countermeasure are the use of masks, which are supposed to filter inhaled and exhaled air to reduce the spread of the virus. The masks, which are medical devices, must be used by providing appropriate instructions for correct use. This study, which examined the population during the advanced stage of the pandemic, highlighted a substantial improvement in the management and choice of masks, even though the information disseminated to the population probably should be even more detailed and precise in order to avoid incorrect behavior that could compromise the effectiveness of these devices; in fact a high percentage of subjects had behaviors that can facilitate the spread of the virus, such as the continuous attempts to correct the incorrect positioning of the mask on the face or the need to move it because it is annoying.

Alternative Methods of Sterilization in Dental Practices Against COVID-19.

SARS-CoV-2, and several other microorganisms, may be present in nasopharyngeal and salivary secretions in patients treated in dental practices, so an appropriate clinical behavior is required in order to avoid the dangerous spread of infections. COVID-19 could also be spread when patients touches a contaminated surface with infected droplets and then touch their nose, mouth, or eyes. It is time to consider a dental practice quite similar to a hospital surgery room, where particular attention should be addressed to problems related to the spreading of infections due to air and surface contamination. The effectiveness of conventional cleaning and disinfection procedures may be limited by several factors; first of all, human operator dependence seems to be the weak aspect of all procedures. The improvement of these conventional methods requires the modification of human behavior, which is difficult to achieve and sustain. As alternative sterilization methods, there are some that do not depend on the operator, because they are based on devices that perform the entire procedure on their own, with minimal human intervention. In conclusion, continued efforts to improve the traditional manual disinfection of surfaces are needed, so dentists should consider combining the use of proper disinfectants and no-touch decontamination technologies to improve sterilization procedures.

Retention strength of ball-attachment titanium post for removable partial denture or overdenture

Aim: To evaluate the retention of an endodontic titanium postwith a spherical head for removable partial denture or overdentureattachment according to surface treatment type. Methods: Sixtyhealthy single-rooted teeth, sectioned at the enamel/cementumjunction, were treated endodontically and steadily fixed in theembedding acrylic resin. The titanium posts were subdivided intofour groups: control, no surface treatment (Ctrl); posts with macroretentivegrooves (MR); air abrasion of the post surface (AB); andposts with macro-retentive grooves and air abrasion of the postsurface (MR+AB). The posts were luted in the root canal usingself-adhesive dual resin cement. Pull-out testing was performedusing a universal testing machine until complete detachment wasachieved. After pull-out testing, the metallic posts were examinedunder an optical microscope and the failures were classifiedbased on the cement distribution pattern on the extracted posts:0, no cement left on the post (cement/post failure); 1, postsurface partially covered by adhered cement (post/cement anddentin/cement mixed failure); 2, post surface completely coveredby cement (dentin/cement failure). The retention data wereanalyzed by one-way ANOVA, Bonferroni­Dunn test (p<0.05)and Weibull analysis. Results: AB showed the highest retentionvalue (485.37±68.36), followed by MR+AB (355.80±118.47), MR(224.63±42.54) and Ctrl (113.12 ± 51.32). AB and MR showedthe highest Weibull moduli. Conclusions: The data indicatedthat air abrasion alone could significantly increase the retentionof titanium posts/attachments for use with overdentures orremovable partial denture

Monitoring blood biomarkers to predict nivolumab effectiveness in NSCLC patients.

BACKGROUND: We investigated whether early dynamic changes of circulating free (cfDNA) levels as well as the neutrophil to lymphocyte ratio (NLR) could predict nivolumab effectiveness in pretreated patients with advanced non-small cell lung cancer (NSCLC). METHODS: A total of 45 patients receiving nivolumab 3 mg/kg every 2 weeks were enrolled. Patients underwent a computed tomography scan and responses were evaluated by the response evaluation criteria in solid tumors. Peripheral blood samples were obtained from the patients and the cfDNA level as well as the NLR were assessed. Time to progression (TTP) and overall survival (OS) were determined. RESULTS: Patients with increased cfDNA >20% at the sixth week reported significantly worse survival outcomes (median OS: 5.7 versus 14.2 months, p < 0.001; median TTP: 3.3 versus 10.2 months, p < 0.001), as well as patients with increased NLR >20% (median OS: 8.7 versus 14.6 months, p = 0.035; median TTP: 5.2 versus 10.3 months, p = 0.039). The combined increase of cfDNA and NLR >20% was associated with significantly worse survival outcomes as compared with the remained population (median OS: 5.8 versus 15.5 months, p = 0.012; median TTP: 3.2 versus 11.9 months, p = 0.028). Multivariable analysis identified three significant factors associated with worse OS: combined cfDNA/NLR increase >20% [hazard ratio (HR): 5.16; 95% confidence interval (CI), 1.09-24.29; p = 0.038], liver metastasis (HR: 0.44; 95% CI, 0.20-0.96; p = 0.038), and extra-thoracic disease (HR: 0.33; 95% CI, 0.12-0.89; p = 0.029). CONCLUSION: An early combined increase of both cfDNA and NLR over the course of the first 6 weeks of nivolumab therapy predicted worse survival in pretreated patients with advanced NSCLC, suggesting a potential role in the real-time monitoring of immunotherapy resistance.

Evaluation of marginal leakage after mechanical fatigue cycling of composite inlays luted with different cements.

This in vitro study evaluated the marginal microleakage of composite inlays luted with 3 different cement systems. The null hypothesis was that the luting materials would not influence dye penetration, showing the same degree of microleakage. Thirty-six sound molars were selected, mesio-occlusodistal cavities were prepared, and the teeth were randomly divided into 3 groups (n = 12). Composite resin inlay restorations were made and cemented using a dual-curing resin cement (Calibra), a light-curing flowable composite (Charisma Flow), or a self-adhesive resin cement (RelyX Unicem). The restored teeth were subjected to fatigue cycles and immersed in 0.5% basic fuchsin dye for 24 hours. Two orthogonal cuts were made to enable evaluation of dye penetration at the cervical and occlusal margins. The sections were evaluated with a 4-point scale ranging from 0 (no penetration) to 3 (penetration up to the cavity floor [occlusal margins] or axial wall [cervical margins]). The Calibra and Charisma Flow groups showed greater microleakage, notably at the cervical margins, whereas RelyX Unicem specimens showed the least dye penetration. Significant differences were found between the Calibra and Charisma Flow groups and between the Charisma Flow and RelyX Unicem groups (P < 0.05). No statistically significant differences were detected between the Calibra and RelyX Unicem groups. The microleakage associated with the flowable composite was significantly greater than that associated with both resin cements, results that discourage its use for luting of Class II composite inlays.

Assessment of root canal enlargement using Mtwo and BioRace rotary files.

OBJECTIVE: To evaluate root canal enlargement following mechanical shaping using 2 nickel titanium rotary systems. MATERIAL AND METHODS: Forty single-rooted teeth were immersed in resin and sectioned perpendicular to the long axis at 4, 8, and 12 mm from the apex. Digital capture of sections was performed before and after canal instrumentation using Mtwo and BioRace instruments. The area increase of endodontic space was calculated by subtraction. RESULTS: The use of both instruments has allowed the removal of great amounts of dentin from the canal walls, even when the endodontic morphology is characterized by awkwardness to reach recesses. CONCLUSIONS: Both procedures seem to be valid and no differences were found between Mtwo and BioRaCe considering the amount of dentin removed at different distances from the apex.

Short-term response of three resin-based materials as desensitizing agents under oral environmental exposure.

OBJECTIVE: This paper focuses on clinical responses after 7 days of oral exposure to two resin-based materials as desensitizing agents compared to a fluoride varnish and on morphological and analytical study as a means to elucidate the mechanism of action. MATERIALS AND METHODS: The elemental composition of Vertise™ Flow (VF), Universal Dentine Sealant (UDS) and Flor-Opal® Varnish (FOV) were investigated by using an X-ray energy dispersive spectrometer (EDX) in conjunction with a scanning electron microscope (SEM). SEM morphology of the material-treated dentine surfaces and pain reduction ability according to the Visual Analogue Scale (VAS) were evaluated in selected hypersensitive teeth. Post treatments and 7 day controls were recorded with SEM and VAS measurements. Clinical data was analysed with the Student's t-test for paired data, with a 5% significance level. RESULTS: Silicon, ytterbium and alumina were the most present elements in VF, whilst calcium, chloride, silicon and alumina were highest in UDS. Within a 7 day oral environment all the tested materials modified the treated-dentine surfaces showing tubular occlusion of different morphology. Clinically, the efficacy of all materials was similar after a 7-day examination. However, VAS scores were significantly reduced if compared with the baseline (p < 0.05). CONCLUSIONS: Within the limits of this study, data indicate that both resins are effective in sealing tubules and reducing VAS. A resin-related effect on the dentine's morphology was observed, which may influence the long-term response of the resins in the treatment of dental hypersensitivity, which requires further investigation.

System B, Endo-Twinn and E-Fill. True temperatures inside the canal.

BACKGROUND: The aim of this study is to verify the variations of the temperature inside the root canal with three different gutta-percha heating systems. MATERIALS AND METHODS: A split-tooth model was built with a lateral groove at 3.5-mm from working length (WL) in order to insert a Chromel-Alumel K-type thermocouple placed in contact with gutta-percha. The thermocouple was connected to a digital thermometer. Sixty obturations were made with medium gutta-percha points. For 20 specimens the System B was used with the Buchanan fine plugger and the temperature was set at 200°C; for other 20 specimens the Endo-Twinn with a fine plugger was used and for the last 20 specimens we used the E-Fill with a 40.04 plugger. All pluggers were pushed to 3.5 mm from WL so that the tips were in contact to the probe. RESULTS: The analysis of 60 samples showed the highest temperature average using the System B after 10 seconds (86.85°C), after 15 seconds (94.9°C), after 20 seconds (100.4°C) and after 25 seconds (104.5°C). The Endo-Twinn average values are similar to System-B ones. The E-Fill average values are lower (69.9°C) than the other two systems evaluated only after 10 seconds due to limited working time. The temperatures average obtained using different systems of warm vertical compaction are lower than what was declared by the producing companies. CONCLUSION: Time is one the most important parameters to consider using these systems. Temperatures reached from the System B and Endo-Twinn after 25 seconds; however, seem to be sufficient to ensure an optimal adaptation of the gutta-percha in the anatomical complexity of root canals. The temperatures obtained from the E-Fill, only after 10 seconds, instead seems to be insufficient to assure the rheological characteristics of gutta-percha.

Current dental adhesives systems. A narrative review.

Adhesive dentistry is based on the development of materials which establish an effective bond with the tooth tissues. In this context, adhesive systems have attracted considerable research interest in recent years. Successful adhesive bonding depends on the chemistry of the adhesive, on appropriate clinical handling of the material as well as on the knowledge of the morphological changes caused on dental tissue by different bonding procedures. This paper outlines the status of contemporary adhesive systems, with particular emphasis on chemical characteristics and mode of interaction of the adhesives with enamel and dentinal tissues. Dental adhesives are used for several clinical applications and they can be classified based on the clinical regimen in "etch-and-rinse adhesives" and "self-etch adhesives". Other important considerations concern the different anatomical characteristics of enamel and dentine which are involved in the bonding procedures that have also implications for the technique used as well as for the quality of the bond. Etch-and-rinse adhesive systems generally perform better on enamel than self-etching systems which may be more suitable for bonding to dentine. In order to avoid a possible loss of the restoration, secondary caries or pulp damage due to bacteria penetration or due to cytotoxicity effects of eluted adhesive components, careful consideration of several factors is essential in selecting the suitable bonding procedure and adhesive system for the individual patient situation.

Innovations in endodontic filling materials: guttapercha vs Resilon.

One of the goals of endodontic treatment is to achieve a complete, tridimensional, hermetic sealing of the root canal system to prevent the entry of microorganisms or their products through both the coronal and apical pathways. Gutta-percha is the most widely used material for root canal filling and despite its numerous properties, such as biocompatibility and thermoplasticity, it has however an important limit: the lack of adhesion to the canal walls. Attempts to address this problem have been made over the years by using endodontic cements capable of bonding to canal dentine but their tendency to resorption in time can compromise the quality of treatment. The first step towards a real adhesive endodontic filling(4) is rather recent; in fact, it goes back to 2003 when, on the occasion of the American Dental Association (ADA) Annual Session, Resilon Research LLC introduced a new canal filling adhesive system based on a thermoplastic synthetic resin material called Resilon™. The real innovation of this system is its capacity of creating a core made of Resilon™ bonded to the cement which adheres to dentine walls previously conditioned with a self-etching primer(4) so no changes in the techniques of canal preparation are required. The aim of this study was to evaluate the capacity of two filling materials (gutta-percha and Resilon) to adapt to the canal anatomy, especially on the apical third, using the continuous wave of condensation technique. Our data suggest that in the third apical the gutta-percha best shows rheological properties that are as important as the bond capability.

TEM morphological characterization of a one-step self-etching system applied clinically to human caries-affected dentin and deep sound dentin.

PURPOSE: To examine morphologically the hybrid layer of one-step self-etching adhesive, Clearfil S3 Bond (S3bond), in caries-affected dentin (CAD) and deep sound dentin (DSD) cavities performed clinically. For a comparative group, the two-step self etching adhesive Clearfil Protect Bond (Pbond) was used in a similar clinical situation. METHODS: This study was carried out on carious and sound teeth clinically selected for extraction. In carious teeth, CAD was obtained by way of subjective criteria by removing infected tissue to form a cavity bottom. DSD was obtained at a depth of 4 mm in the dentin cavity of sound teeth. S3bond and Pbond were applied in the CAD and DSD cavities as indicated by the manufacturer, followed by a composite restoration. Teeth were extracted about 20 minutes after the bonding procedure, and processed for TEM analysis. RESULTS: Expression of S3bond in CAD was morphologically highly variable. When affected tubules were occluded by intratubular mineralized deposits, the interface displayed a dense poly-HEMA hydrogel as water sorption by the hydrophilic S3bond toward the porous affected collagen. Conversely, when tubules appeared empty, voids of various sizes were formed by tubular fluid shift. In DSD, S3bond clearly exhibited voids and water channels as signs of the high permeability of the sub-surface. Although porosities were somewhat retained, Pbond expression showed a hermetic character which was independent of the dentin substrate.

In vitro evaluation of the antibacterial activity of cured dentin/enamel adhesive incorporating the antimicrobial agent MDPB.

The aim of this study was to investigate in vitro the antibacterial effect of a dentin/enamel adhesive containing MDPB (Clearfil Protect Bond) after curing and to compare it with an adhesive not containing MDPB (Clearfil SE Bond). The antibacterial effect of the cured adhesives was tested on Enterococcus faecalis by the evaluation of growth inhibition in a 48-h microplate direct contact test (DCT). The presence of antibacterial activity due to soluble components was also investigated by an agar diffusion test (ADT) performed with the adhesives cured on the surface of dentin disks. In the DCT, both the tested materials showed complete inhibition of bacterial growth until the 7-h reading, regardless of whether direct contact with the bacterial inoculum was continued or limited to 1 h. Stationary growth phase turbidity levels were observed at 24 or 48-h incubation. The ADT produced no inhibition areas around the dentin disks. Both adhesives tested in vitro under conditions simulating those encountered in the restorative treatment of dental caries were equally able to delay bacterial growth demonstrating a similar bacteriostatic effect. As suggested by both the DCT and the ADT, the antibacterial effect of the two adhesives depends on direct contact and does not seem to be related to the diffusion of soluble components.

How can droplet formation occur in endodontically treated teeth during bonding procedures?

PURPOSE: The aim of this in vivo study was to clarify how blistering formation occurs along intraradicular dentin bonded interfaces. MATERIALS AND METHODS: Patients were selected and post space was prepared in vivo in endodontically treated teeth. Post space was etched, dried with ethanol, and bonded with one of the following adhesive systems: All Bond 2, XP-Bond, Clearfil SE Bond, Xeno III. The four adhesives were considered as representative of each bonding system class. An additional group was prepared with phosphoric acid treatment + application of Pre-Bond unfilled resin of All Bond 2, without the use of the primer agent. Etching was avoided for self-etching materials. Replicas of the post space were taken (1) after post space preparation; (2) after etching, rinsing, and drying; (3) after ethanol drying, and (4) after adhesive application. Replicas were analyzed with SEM and blisters were counted by independent observers. Statistical analysis was performed with Kruskal-Wallis ANOVA and Dunn's multiple comparison tests at p = 0.05. RESULTS: No blister formation occurred on replicas taken prior to adhesive application, while blister formation was evident in all replicas of bonded interfaces, irrespective of the adhesive system. No statistical difference in the number of droplets was found between All Bond 2, XP-Bond, and Clearfil SE Bond. Xeno III exhibited the highest number of blisters. Specimens bonded with Pre-Bond unfilled resin of All Bond 2 without primer application showed no blister formation. CONCLUSION: This study revealed that blister formation occurs only if the priming agent of the adhesive system was applied, thus supporting the hypothesis that blistering occurs due to adhesive phase separation or insufficient solvent evaporation.

Ultrasound effects after post space preparation: An SEM study.

The aim of this study was to evaluate the effect of ultrasonic treatment on occlusion of dentine tubules in root canal walls after post space preparation in endodontically treated teeth. Twenty-four premolars were instrumented and filled using warm vertical condensation; after post space preparation, they were divided into two groups. The control group was treated using the etching procedure. The experiment samples were treated with EDTA irrigation and ultrasound activation for 30 s before the etching procedure. The roots were divided and the canal walls were examined under SEM at 1000x magnification. The debris and open tubule marks were observed at 2, 6, and 10 mm levels using a three-step scale and the differences in marks among the groups were tested for statistical significance. The following were observed: (a) A decrease in debris and open tubule marks in the samples treated with ultrasounds and the control group (p < 0.05), (b) no significant differences between the three levels of post space in debris and open tubule marks in the experiment samples, and (c) significant differences between the apical and coronal levels in debris and open tubule marks in the control group.

In vitro antibacterial activity of endodontic sealers.

OBJECTIVES: To evaluate the antibacterial activity of four endodontic sealers: one epoxy resin sealer (AH Plus), two zinc oxide eugenol (ZOE)-based sealers (Endomèthasone, Pulp Canal Sealer), and one sealer containing both ZOE and orthophenilphenol (Vcanalare). METHODS: A direct contact test (DCT) was performed. A 10 microl suspension of Enterococcus faecalis was placed on the test material 20 min, 24 h and 7 days after mixing. Bacteria were allowed to directly contact the sealers for 1h at 37 degrees C. Bacterial growth was then spectrophotometrically measured every 30 min for 7 h, and again after 24 h as well. RESULTS: All freshly mixed sealers showed complete inhibition of bacterial growth. Similar results were obtained with the 24-h-old samples, with the exception of AH Plus. Vcanalare was the only sealer still inhibiting bacterial growth 7 days after mixing. CONCLUSIONS: The antimicrobial activity of the tested sealers depends on the time interval between mixing and testing. All sealers exhibit bactericidal effect when freshly mixed, but only Vcanalare extended this effect until 7 days after setting.

Surface debris of canal walls after post space preparation in endodontically treated teeth: a scanning electron microscopic study.

PURPOSE: To evaluate surface cleanliness of root canal walls along post space after endodontic treatment using 2 different irrigant regimens, obturation techniques, and post space preparation for adhesive bonding. STUDY DESIGN: Forty teeth, divided into 4 groups, were instrumented, using Ni-Ti rotary files, irrigated with NaOCl or NaOCl+EDTA and obturated with cold lateral condensation (CLC) or warm vertical condensation (WVC) of gutta-percha. After post space preparation, etching, and washing procedure, canal walls were observed using a scanning electron microscope (SEM). Amount of debris, smear layer, sealer/gutta-percha remnants, and visibility of open tubules were rated. RESULTS: Higher amounts of rough debris, large sealer/gutta-percha remnants, thick smear layer, and no visibility of tubule orifices were recorded in all the groups at apical level of post space. At middle and coronal levels areas of clean dentin, alternating with areas covered by thin smear layer, smaller debris, gutta-percha remnants, and orifices of tubules partially or totally occluded by plugs were frequently observed. CONCLUSIONS: After endodontic treatment, obturation, and post space preparation SEM analysis of canal walls along post space shows large areas (covered by smear layer, debris, and sealer/gutta-percha remnants) not available for adhesive bonding and resin cementation of fiber posts.