RESUMO
Cathodoluminescence mapping is used as a contactless method to probe the electron concentration gradient of Te-doped GaAs nanowires. The room temperature and low temperature (10 K) cathodoluminescence analysis method previously developed for GaAs:Si is first validated on five GaAs:Te thin film samples, before extending it to the two GaAs:Te NW samples. We evidence an electron concentration gradient ranging from below 1 × 1018cm-3to 3.3 ×1018cm-3along the axis of a GaAs:Te nanowire grown at 640 °C, and a homogeneous electron concentration of around 6-8 × 1017cm-3along the axis of a GaAs:Te nanowire grown at 620 °C. The differences in the electron concentration levels and gradients between the two nanowires is attributed to different Te incorporation efficiencies by vapor-solid and vapor-liquid-solid processes.
RESUMO
Advanced van der Waals (vdW) heterostructure devices rely on the incorporation of high quality dielectric materials which need to possess a low defect density as well as being atomically smooth and uniform. In this work we explore the use of talc dielectrics as a potentially clean alternative substrate to hexagonal boron nitride (hBN) for few-layer transition metal dichalcogenide (TMDC) transistors and excitonic TMDC monolayers. We find that talc dielectric transistors show small hysteresis which does not depend strongly on sweep rate and show negligible leakage current for our studied dielectric thicknesses. We also show narrow photoluminescence linewidths down to 10 meV for different TMDC monolayers on talc which highlights that talc is a promising material for future van der Waals devices.
RESUMO
Precise control and broad tunability of the growth parameters are essential in engineering the optical and electrical properties of semiconductor nanowires (NWs) to make them suitable for practical applications. To this end, we report the effect of As species, namely As2 and As4, on the growth of self-catalyzed GaAs based NWs. The role of As species is further studied in the presence of Te as n-type dopant in GaAs NWs and Sb as an additional group V element to form GaAsSb NWs. Using As4 enhances the growth of NWs in the axial direction over a wide range of growth parameters and diminishes the tendency of Te and Sb to reduce the NW aspect ratio. By extending the axial growth parameter window, As4 allows growth of GaAsSb NWs with up to 47% in Sb composition. On the other hand, As2 favors sidewall growth which enhances the growth in the radial direction. Thus, the selection of As species is critical for tuning not only the NW dimensions, but also the incorporation mechanisms of dopants and ternary elements. Moreover, the commonly observed dependence of twinning on Te and Sb remains unaffected by the As species. By exploiting the extended growth window associated with the use of As4, enhanced Sb incorporation and optical emission up to 1400 nm wavelength range is demonstrated. This wavelength corresponds to the telecom E-band, which opens new prospects for this NW material system in future telecom applications while simultaneously enabling their integration to the silicon photonics platform.
RESUMO
The performance of Ohmic contacts applied to semiconductor nanowires (NWs) is an important aspect for enabling their use in electronic or optoelectronic devices. Due to the small dimensions and specific surface orientation of NWs, the standard processing technology widely developed for planar heterostructures cannot be directly applied. Here, we report on the fabrication and optimization of Pt/Ti/Pt/Au Ohmic contacts for p-type GaAs nanowires grown by molecular beam epitaxy. The devices were characterized by current-voltage (IV) measurements. The linearity of the IV characteristics curves of individual nanowires was optimized by adjusting the layout of the contact metal layers, the surface treatment prior to metal evaporation, and post-processing thermal annealing. Our results reveal that the contact resistance is remarkably decreased when a Pt layer is deposited on the GaAs nanowire prior to the traditional Ti/Pt/Au multilayer layout used for p-type planar GaAs. These findings are explained by an improved quality of the metal-GaAs interface, which was evidenced by grazing incidence X-ray diffraction measurements in similar metallic thin films deposited on GaAs (110) substrates. In particular, we show that Ti exhibits low degree of crystallinity when deposited on GaAs (110) surface which directly affects the contact resistance of the NW devices. The deposition of a thin Pt layer on the NWs prior to Ti/Pt/Au results in a 95% decrease in the total electrical resistance of Be-doped GaAs NWs which is associated to the higher degree of crystallinity of Pt than Ti when deposited directly on GaAs (110).
RESUMO
Effective and controllable doping is instrumental for enabling the use of III-V semiconductor nanowires (NWs) in practical electronics and optoelectronics applications. To this end, dopants are incorporated during self-catalyzed growth via vapor-liquid-solid mechanism through the catalyst droplet or by vapor-solid mechanism of the sidewall growth. The interplay of these mechanisms together with the competition between axial elongation and radial growth of NWs can result in dopant concentration gradients along the NW axis. Here, we report an investigation of Be-doped p-type GaAs NWs grown by the self-catalyzed method on lithography-free Si/SiO x templates. The influence of dopant incorporation on the structural properties of the NWs is analyzed by scanning and transmission electron microscopy. By combining spatially resolved Raman spectroscopy and transport characterization, we are able to estimate the carrier concentration, mobility and resistivity on single-NW level. We show that Be dopants are incorporated predominantly by vapor-solid mechanism for low Be flux, while the relative contribution of vapor-liquid-solid incorporation is increased for higher Be flux, resulting in axial dopant gradients that depend on the nominal doping level.