Printed graphene and its composite with copper for electromagnetic interference shielding applications.

Advances in mobile electronics and telecommunication systems along with 5G technologies have been escalating the electromagnetic interference (EMI) problem in recent years. Graphene-based material systems such as pristine graphene, graphene-polymer composites and other graphene-containing candidates have been shown to provide adequate EMI shielding performance. Besides achieving the needed shielding effectiveness (SE), the method of applying the candidate shielding material onto the object in need of protection is of enormous importance due to considerations of ease of application, reduced logistics and infrastructure, rapid prototyping and throughput, versatility to handle both rigid and flexible substrates and cost. Printing readily meets all these criteria and here we demonstrate plasma jet printing of thin films of graphene and its composite with copper to meet the EMI shielding needs. SE over 30 dB is achieved, which represents blocking over 99.9% of the incoming radiation. Graphene and its composite with copper yield higher green index compared to pure copper shields, implying reduced reflection of incoming electromagnetic waves to help reduce secondary pollution.

Plasma Jet Printing and in Situ Reduction of Highly Acidic Graphene Oxide.

Miniaturization of electronic devices and the advancement of Internet of Things pose exciting challenges to develop technologies for patterned deposition of functional nanomaterials. Printed and flexible electronic devices and energy storage devices can be embedded onto clothing or other flexible surfaces. Graphene oxide (GO) has gained much attention in printed electronics due its solution processability, robustness, and high electrical conductivity in the reduced state. Here, we introduce an approach to print GO films from highly acidic suspensions with in situ reduction using an atmospheric pressure plasma jet. Low-temperature plasma of a He and H2 mixture was used successfully to reduce a highly acidic GO suspension (pH < 2) in situ during deposition. This technique overcomes the multiple intermediate steps required to increase the conductivity of deposited GO. X-ray spectroscopic studies confirmed that the reaction intermediates and the concentration of oxygen functionalities bonded to GO have been reduced significantly by this approach without any additional steps. Moreover, the reduced GO films showed enhanced conductivity. Hence, this technique has a strong potential for printing conducting patterns of GO for a range of large-scale applications.

Morphological and chemical changes of aerosolized E. coli treated with a dielectric barrier discharge.

This study presents the morphological and chemical modification of the cell structure of aerosolized Escherichia coli treated with a dielectric barrier discharge (DBD). Exposure to DBD results in severe oxidation of the bacteria, leading to the formation of hydroxyl groups and carbonyl groups and a significant reduction in amine functionalities and phosphate groups. Near edge x-ray absorption fine structure (NEXAFS) measurements confirm the presence of additional oxide bonds upon DBD treatment, suggesting oxidation of the outer layer of the cell wall. Electron microscopy images show that the bacteria undergo physical distortion to varying degrees, resulting in deformation of the bacterial structure. The electromagnetic field around the DBD coil causes severe damage to the cell structure, possibly resulting in leakage of vital cellular materials. The oxidation and chemical modification of the bacterial components are evident from the Fourier transform infrared spectroscopy and NEXAFS results. The bacterial reculture experiments confirm inactivation of airborne E. coli upon treating with DBD.

Plasma jet printing of electronic materials on flexible and nonconformal objects.

We present a novel approach for the room-temperature fabrication of conductive traces and their subsequent site-selective dielectric encapsulation for use in flexible electronics. We have developed an aerosol-assisted atmospheric pressure plasma-based deposition process for efficiently depositing materials on flexible substrates. Silver nanowire conductive traces and silicon dioxide dielectric coatings for encapsulation were deposited using this approach as a demonstration. The paper substrate with silver nanowires exhibited a very low change in resistance upon 50 cycles of systematic deformation, exhibiting high mechanical flexibility. The applicability of this process to print conductive traces on nonconformal 3D objects was also demonstrated through deposition on a 3D-printed thermoplastic object, indicating the potential to combine plasma printing with 3D printing technology. The role of plasma here includes activation of the material present in the aerosol for deposition, increasing the deposition rate, and plasma polymerization in the case of inorganic coatings. The demonstration here establishes a low-cost, high-throughput, and facile process for printing electronic components on nonconventional platforms.

Scalable low-cost fabrication of disposable paper sensors for DNA detection.

Controlled integration of features that enhance the analytical performance of a sensor chip is a challenging task in the development of paper sensors. A critical issue in the fabrication of low-cost biosensor chips is the activation of the device surface in a reliable and controllable manner compatible with large-scale production. Here, we report stable, well-adherent, and repeatable site-selective deposition of bioreactive amine functionalities and biorepellant polyethylene glycol-like (PEG) functionalities on paper sensors by aerosol-assisted, atmospheric-pressure, plasma-enhanced chemical vapor deposition. This approach requires only 20 s of deposition time, compared to previous reports on cellulose functionalization, which takes hours. A detailed analysis of the near-edge X-ray absorption fine structure (NEXAFS) and its sensitivity to the local electronic structure of the carbon and nitrogen functionalities. σ*, π*, and Rydberg transitions in C and N K-edges are presented. Application of the plasma-processed paper sensors in DNA detection is also demonstrated.

X-ray Absorption Study of Graphene Oxide and Transition Metal Oxide Nanocomposites.

The surface properties of the electrode materials play a crucial role in determining the performance and efficiency of energy storage devices. Graphene oxide and nanostructures of 3d transition metal oxides were synthesized for construction of electrodes in supercapacitors, and the electronic structure and oxidation states were probed using near-edge X-ray absorption fine structure. Understanding the chemistry of graphene oxide would provide valuable insight into its reactivity and properties as the graphene oxide transformation to reduced-graphene oxide is a key step in the synthesis of the electrode materials. Polarized behavior of the synchrotron X-rays and the angular dependency of the near-edge X-ray absorption fine structures (NEXAFS) have been utilized to study the orientation of the σ and π bonds of the graphene oxide and graphene oxide-metal oxide nanocomposites. The core-level transitions of individual metal oxides and that of the graphene oxide nanocomposite showed that the interaction of graphene oxide with the metal oxide nanostructures has not altered the electronic structure of either of them. As the restoration of the π network is important for good electrical conductivity, the C K edge NEXAFS spectra of reduced graphene oxide nanocomposites confirms the same through increased intensity of the sp2-derived unoccupied states π* band. A pronounced angular dependency of the reduced sample and the formation of excitonic peaks confirmed the formation of extended conjugated network.

Label-free detection of cardiac troponin-I using carbon nanofiber based nanoelectrode arrays.

A label-free biosensor is presented using carbon nanofiber (CNF) nanoelectrode arrays for the detection of cardiac troponin-I in the early diagnosis of myocardial infarction. Immobilization of anti-cTnI Ab on CNFs and the detection of human-cTnI were examined using electrochemical impedance spectroscopy and cyclic voltammetry techniques. Each step of the modification process was monitored, and the results show changes in electrical capacitance or resistance to charge transfer due to the specificity of corresponding adsorption of Ab-Ag interaction. The immunosensor demonstrates a good selectivity and high sensitivity against human-cTnI analytes and is capable of detecting cTnI at concentrations as low as ∼0.2 ng/mL, which is 25 times lower than that possible by conventional methods. Analysis of the electrode at various stages using atomic force microscopy and X-ray reflectivity provides information on the surface roughness and orientation of the antibody.

Simple approach to study biomolecule adsorption in polymeric microfluidic channels.

Herein a simple analytical method is presented for the characterization of biomolecule adsorption on cyclo olefin polymer (COP, trade name: Zeonor(®)) substrates which are widely used in microfluidic lab-on-a-chip devices. These Zeonor(®) substrates do not possess native functional groups for specific reactions with biomolecules. Therefore, depending on the application, such substrates must be functionalized by surface chemistry methods to either enhance or suppress biomolecular adsorption. This work demonstrates a microfluidic method for evaluating the adsorption of antibodies and oligonucleotides surfaces. The method uses centrifugal microfluidic flow-through chips and can easily be implemented using common equipment such as a spin coater. The working principle is very simple. The user adds 40 L of the solution containing the sample to the starting side of a microfluidic channel, where it is moved through by centrifugal force. Some molecules are adsorbed in the channel. The sample is then collected at the other end in a small reservoir and the biomolecule concentration is measured. As a pilot application, we characterized the adsorption of goat anti-human IgG and a 20-mer DNA on Zeonor(®), and on three types of functionalized Zeonor: 3-aminopropyltriethoxysilane (APTES) modified surface with mainly positive charge, negatively charged surface with immobilized bovine serum albumin (BSA), and neutral, hydrogel-like film with polyethylene glycol (PEG) characteristics. This simple analytical approach adds to the fundamental understanding of the interaction forces in real, microfluidic systems. This method provides a straightforward and rapid way to screen surface compositions and chemistry, and relate these to their effects on the sensitivity and resistance to non-specific binding of bioassays using them. In an additional set of experiments, the surface area of the channels in this universal microfluidic chip was increased by precision milling of microscale trenches. This modified surface was then coated with APTES and tested for its potential to serve as a unique protein dilution feature.

Reactive deposition of nano-films in deep polymeric microcavities.

We report the controlled diffusion of gas-phase high-reactivity chemical species into long polymeric microcavities to form glass-like, low-permeability barrier films on the interior surfaces of the microcavities. Reactive species created from fragmentation of O(2) and hexamethyldisiloxane (HMDSO) in a radio-frequency (RF) plasma environment are allowed to diffuse into the microcavities of polydimethylsiloxane (PDMS), where surface reactions lead to the formation of an effective, glass-like thin-film barrier. Reactive species including silicon radicals and elemental oxygen maintain their reactivity for sufficient times (up to 7000 s) and survive the random diffusional walk through the microcavities to form glass barriers as much as 65 mm from the cavity entrance. The barrier thickness and the growth length can be controlled by the reaction time and chamber operating pressure. Increasing the cross sectional area of the cavity inlet and/or decreasing the mean free path was found to increase the thickness of the barrier film. Optical emission spectroscopic analysis was used to characterize the reactive fragments formed from HMDSO, and energy-dispersive X-ray analysis revealed that the barrier composition is consistent with oxides of silicon (SiO(x)). Formed inside PDMS microcavities, the glass barrier blocks the penetration or absorption of small molecules such as rhodamine B (RhB) and biotin, and also resists permeation of organic solvents such as toluene, preventing the PDMS microfluidic structures from swelling and deforming. Moreover, formation of glass-like thin films in PDMS microcavities enhances the stability of electroosmotic flow (EOF) relative to uncoated PDMS devices, in which EOF instabilities are significant; this enables separation by electrophoresis with reproducibility (relative standard deviation 3%, n = 5) and baseline peak resolution (R:1.3) comparable to that obtained in conventional fused-silica capillaries.

Protection and functionalisation of silver as an optical sensing platform for highly sensitive SPR based analysis.

Silver thin films are well known as the most sensitive material for surface plasmon resonance (SPR) based analysis. However, the use of silver for this purpose is limited by three main issues, namely poor adhesion to plastic substrates, chemical instability in both air and aqueous environments and hence the difficulty in functionalizing the silver coated substrate for immobilizing biomolecular ligands by conventional liquid phase methods. In this work, we have successfully addressed these problems using gas-phase coating processes. We demonstrate highly adherent sputter-deposited silver coatings on low cost polymer substrates using a sputter-deposited thin gold adhesion layer. The problems of chemical instability and functionalisation have been addressed by using the gas phase process of plasma enhanced chemical vapour deposition (PECVD) to deposit thin films with a base SiO(x)C(y)H(z) layer (using tetraethyl orthosilicate precursor) functionalised with carboxylic acid (from sequential deposition with acrylic acid precursor). The resultant coating serves as a protective layer against degradation of the optical properties of silver under long term storage and use in ambient conditions. The reactive carboxyl functionality is used for the covalent immobilization of biomolecules. The successful stabilisation and functionalization of silver films on plastic sensor chips is demonstrated by mouse IgG immunoassays. The expected superior performance of the silver thin films over gold thin films for SPR analysis is demonstrated.

Improving the sensitivity of immunoassays with PEG-COOH-like film prepared by plasma-based technique.

Herein we report on a preparation and performance of stable, hydrophilic and biocompatible polymeric material suitable for functionalization of disposable substrates used in biosensors. This new material features COOH surface groups cross-linked with ethylene glycol molecules and was prepared in situ on disposable, plastic substrate by high-throughput and environmentally friendly technique called plasma-enhanced chemical vapor deposition (PECVD). The film is grafted to the plasma activated plastic by sequential deposition of tetraethylorthosilicate, forming a bonding layer, and mixed vapors of acrylic acid and diethyleneglycol dimethylether (AA/PEG) that provide the desired functional groups forming a sensing, contact layer. A superior performance of the AA/PEG coating as suitable material for substrates in biomedical devices was demonstrated in a model fluorescence linked immunosorbent assay. The results were compared with other commonly used surface materials prepared by wet chemistry methods. The unique characteristic of the AA/PEG film is that the immunoassay can be executed without the need for a blocking step, typically using albumins, without negative consequences on the bioassay results. In fact, the superior quality of the materials modified with AA/PEG film was highlighted by improving the sensitivity of an immunoassay by two orders of magnitude when compared with substrates prepared by standard surface chemistry methods.

Multi-layered plasma-polymerized chips for SPR-based detection.

The surface functionalization of a noble metal is crucial in a surface plasmon resonance-based biomolecular detection system because the interfacial coating must retain the activity of immobilized biomolecules while enhancing the optimal loading. We present here a one-step, room-temperature, high-speed, gas-phase plasma polymerization process for functionalizing gold substrates using siloxane as an adhesion layer and acrylic acid as a functional layer. Siloxane- and thiol-based coatings were compared for their performance as adhesion and the interfacial layer for subsequent functionalization. An in situ sequential deposition of siloxane and acrylic acid resulted in a 7-fold increase in carboxylic functionality surfacial content compared to films deposited with thiol-containing precursors. Grading of the layer composition achieved as a consequence of ion-induced mixing on the surface coating under the application of the plasma is confirmed through secondary ion mass spectroscopic studies. DNA hybridization assays were demonstrated on gold/glass substrates using surface plasmon enhanced ellipsometry and the applicability of this coating for protein immunoassays were demonstrated with plasma functionalized gold/plastic substrates in Biacore 3000 SPR instrument.

Evaluation of different nonspecific binding blocking agents deposited inside poly(methyl methacrylate) microfluidic flow-cells.

Poly(methyl methacrylate) (PMMA) flow-cells containing microwells were deposited with different nonspecific binding blocking agents, namely, bovine serum albumin (BSA), cationic lipid (DOTAP:DOPE) and diethylene glycol dimethyl ether (DEGDME). Water contact angle (WCA) and atomic force microscope (AFM) measurements were carried out to confirm the successful depositions of BSA, DOTAP, and DEGDME onto the PMMA surfaces. Fluorescent intensity measurements were performed to evaluate the degree of nonspecific adsorption of Cy5-labeled anti-IgG proteins onto plain and oxygen plasma-treated (PT) PMMA flow-cells as well as PMMA flow-cells deposited with different above-mentioned blocking agents. We then employed a label-free detection method called total internal reflection ellipsometry (TIRE) to evaluate the stability of the deposited blocking agents inside the PMMA flow-cells. It was found that, while DOTAP:DOPE was the best agent for blocking the nonspecific adsorption, it could be removed from the PMMA surfaces of the flow-cells upon rinsing with phosphate buffered saline (PBS) and later deposited back onto the Au-coated glass sensing substrate of the TIRE. The removal of the blocking agents from PMMA surfaces and their deposition onto the sensing substrate were further manifested by measuring the kinetics and the amount of adsorbed anti-α-hCG proteins. Overall, the dry DEGDME coating by plasma-enhanced chemical vapor deposition (PECVD) showed very good blocking and excellent stability for subsequent assay inside the microwells. Our results could be useful when one considers what blocking agents should be used for PMMA-based microfluidic immunosensor or biosensor devices by looking at both the blocking efficiency and the stability of the blocking agent.

TIRF microscopy as a screening method for non-specific binding on surfaces.

We report a method for studying nanoparticle-biosensor surface interactions based on total internal reflection fluorescence (TIRF) microscopy. We demonstrate that this simple technique allows for high throughput screening of non-specific adsorption (NSA) of nanoparticles on surfaces of different chemical composition. Binding events between fluorescent nanoparticles and functionalized Zeonor® surfaces are observed in real-time, giving a measure of the attractive or repulsive properties of the surface and the kinetics of the interaction. Three types of coatings have been studied: one containing a polymerized aminosilane network with terminal -NH(2) groups, a second film with a high density of -COOH surface groups and the third with sterically restraining branched poly(ethylene)glycol (PEG) functionality. TIRF microscopy revealed that the NSA of nanoparticles with negative surface charge on such modified coatings decreased in the following order -NH(2)>-branched PEG>-COOH. The surface specificity of the technique also allows discrimination of the degree of NSA of the same surface at different pH.

Functionalization of cyclo-olefin polymer substrates by plasma oxidation: stable film containing carboxylic acid groups for capturing biorecognition elements.

Many current designs in biomedical diagnostics devices are based on the use of low cost, disposable, easy-to-fabricate chips made of plastic material, typically a cyclo-olefin polymer (COP). Low autofluorescence properties of such material, among others, make it ideal substrate for fluorescence-based applications. Functionalization of this plastic substrate for biomolecule attachment is therefore of great importance and the quality of films produced on such surface have often a significant influence on the performance of the device. In this communication we discuss the surface chemistry and some other characteristics of hydrophilic films, containing carboxylic acid functional groups, formed by plasma oxidation of COP and also films containing cross-linked, polymerized acryclic acid produced by sequential deposition of tetraorthosilicate and acrylic acid by plasma enhanced chemical vapor deposition (PECVD). Immobilization of labeled, single stranded DNA revealed high binding capacity for both coatings. To our best knowledge, this is the first example of direct immobilization of biomolecules on just plasma oxidized COP. Furthermore, more sophisticated treatment of the oxidized plastic substrate by PECVD with other organic precursors increased the binding capacity by some 40% than that of just plasma oxidized COP. The carboxy functionalized surfaces, due to the negative charge of the carboxy groups, showed very positive trends towards increasing the signal to noise ratio when charged biomolecules such as DNA, are used.

Total internal reflection ellipsometry as a label-free assessment method for optimization of the reactive surface of bioassay devices based on a functionalized cycloolefin polymer.

We report a label-free optical detection technique, called total internal reflection ellipsometry (TIRE), which can be applied to study the interactions between biomolecules and a functionalized polymer surface. Zeonor (ZR), a cycloolefin polymer with low autofluorescence, high optical transmittance and excellent chemical resistance, is a highly suitable material for optical biosensor platforms owing to the ease of fabrication. It can also be modified with a range of reactive chemical groups for surface functionalization. We demonstrate the applications of TIRE in monitoring DNA hybridization assays and human chorionic gonadotrophin sandwich immunoassays on the ZR surface functionalized with carboxyl groups. The Ψ and Δ spectra obtained after the binding of each layer of analyte have been fitted to a four-layer ellipsometric model to quantitatively determine the amount of analytes bound specifically to the functionalized ZR surface. Our proposed TIRE technique with its very low analyte consumption and its microfluidic array format could be a useful tool for evaluating several crucial parameters in immunoassays, DNA interactions, adsorption of biomolecules to solid surfaces, or assessment of the reactivity of a functionalized polymer surface towards a specific analyte.

Plasma functionalization of AFM tips for measurement of chemical interactions.

In this paper, a new, fast, reproducible technique for atomic force microscopy (AFM) tips functionalization used for chemical interaction measurements is described. Precisely, the deposition of an aminated precursor is performed through plasma-enhanced chemical vapor deposition (PECVD) in order to create amine functional groups on the AFM tip and cantilever. The advantages of the precursor, aminopropyltriethoxysilane (APTES), were recently demonstrated for amine layer formation through PECVD deposition on polymeric surfaces. We extended this procedure to functionalize AFM probes. Titration force spectroscopy highlights the successful functionalization of AFM tips as well as their stability and use under different environmental conditions.

Functionalization of cycloolefin polymer surfaces by plasma-enhanced chemical vapour deposition: comprehensive characterization and analysis of the contact surface and the bulk of aminosiloxane coatings.

The surface science of bioassay devices is of great importance in the development of modern diagnostic platforms. The quality of surface is one of the most important elements of the device, often governing the background response, hence controlling the sensitivity of an assay. Detailed surface characterization and analysis are imperative for the preparation of reproducible coatings with desired properties. We performed a comprehensive characterization of 3-aminopropyl-triethoxysilane films prepared under two different deposition conditions on COP slides. Two sets of slides were prepared, by exposing them to plasma reaction for 30 seconds (A30 slide) and 4 minutes (A4 slide). While the variations in the deposition conditions seemed very subtle, the use of several powerful analytical tools helped us to reveal some fundamental differences between the studied films in terms of binding capacity, swelling and adhesion. Overall, the A30 films, with a thickness of 5.12 nm, showed up to 40% higher binding capacity and 25% better adhesion than the thicker A4 coatings (28.15 nm). Upon contact with aqueous media, a significant change was observed in terms of surface roughness. The A30 slides outperformed A4 slides, resulting in smoother surface, which is an important parameter for biomolecule immobilisation. The use of the techniques described in this article is aimed to set new standards for the characterization and analysis of the substrate surface of the future diagnostic devices.