Pluronic F-127 Enhances the Antifungal Activity of Fluconazole against Resistant Candida Strains.

Candida strains as the most frequent causes of infections, along with their increased drug resistance, pose significant clinical and financial challenges to the healthcare system. Some polymeric excipients were reported to interfere with the multidrug resistance mechanism. Bearing in mind that there are a limited number of marketed products with fluconazole (FLU) for the topical route of administration, Pluronic F-127 (PLX)/FLU formulations were investigated in this work. The aims of this study were to investigate (i) whether PLX-based formulations can increase the susceptibility of resistant Candida strains to FLU, (ii) whether there is a correlation between block polymer concentration and the antifungal efficacy of the FLU-loaded PLX formulations, and (iii) what the potential mode of action of PLX assisting FLU is. The yeast growth inhibition upon incubation with PLX formulations loaded with FLU was statistically significant. The highest efficacy of the azole agent was observed in the presence of 5.0 and 10.0% w/v of PLX. The upregulation of the CDR1/CDR2 genes was detected in the investigated Candida strains, indicating that the efflux of the drug from the fungal cell was the main mechanism of the resistance.

Screening of Fenofibrate-Simvastatin Solid Dispersions in the Development of Fixed-Dose Formulations for the Treatment of Lipid Disorders.

The combination of statins and fibrates in the treatment of lipid abnormalities effectively regulates individual lipid fraction levels. In this study, the screening and assessment of the physicochemical properties of simvastatin-fenofibrate solid dispersions were performed. Fenofibrate and simvastatin were processed using the kneading method in different weight ratios, and the resulting solid dispersions were assessed using differential scanning calorimetry (DSC), X-ray powder diffractometry (XRPD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), contact angle, as well as dissolution tests. The obtained results confirmed the formation of a simple eutectic phase diagram, with a eutectic point containing 79 wt% fenofibrate and 21 wt% simvastatin, lack of chemical interactions between the ingredients, and simvastatin impact on improving fenofibrate dissolution profile, due to the formation of crystalline solid dispersions by the kneading method.

The Effect of High-Pressure Homogenization Conditions on the Physicochemical Properties and Stability of Designed Fluconazole-Loaded Ocular Nanoemulsions.

The growing interest in high-energy emulsification is a result of its scalability, which is important from an industrial perspective and allows for a more reproducible and efficient production of pharmaceutical formulations. The aim of this study was to evaluate the effect of composition, mainly a fixed surfactant/cosurfactant (Smix) ratio, their concentration, and the parameters of high-pressure homogenization (HPH) processing on the quality and stability of ophthalmic fluconazole-loaded nanoemulsions. After a physicochemical analysis of nanoemulsions containing 20% w/w of oil, as optimal conditions for the HPH process, three cycles at a pressure of 1000 bar were established, obtaining formulations with an average droplet diameter size in the range of 80.63-129.68 nm and PDI values below 0.25. While it was expected that an increasing cosurfactant concentration decreased the droplet size, in the case of formulations containing Tween 20 and 10% w/w of cosurfactants, "over-processing" was observed, identified by the droplet size and polydispersity index increase. Consecutively, the selected formulations were evaluated for in vitro drug release in Franz's cell, antifungal activity, and 30-day stability using NMR spectroscopy. An antifungal activity test showed no significant difference in the antifungal activity between optimal fluconazole-loaded nanoemulsions and a 0.3% aqueous drug solution, but previously, research showed that prepared formulations were characterized by a higher viscosity and satisfactory prolonged release compared to a control. In a 30-day stability study, it was observed that higher HLB values of the used surfactants decreased the stability of the formulations in the following order: Kolliphor EL, Tween 80, Tween 20. The NMR spectra confirmed that Kolliphor EL-based formulations ensured the higher stability of the nanoemulsion composition in comparison to Tween 80 and a better stabilizing effect of propylene glycol as a cosurfactant in comparison to PEG 200. Therefore, the optimization of HPH technology should be focused on the selection of Smix and the Smix:oil ratio in order to prepare stable formulations of high quality.

Ophthalmic Nanoemulsions: From Composition to Technological Processes and Quality Control.

Nanoemulsions are considered as the most promising solution to improve the delivery of ophthalmic drugs. The design of ophthalmic nanoemulsions requires an extensive understanding of pharmaceutical as well as technological aspects related to the selection of excipients and formulation processes. This Review aims at providing the readers with a comprehensive summary of possible compositions of nanoemulsions, methods for their formulation (both laboratory and industrial), and differences between technological approaches, along with an extensive outline of the research methods enabling the confirmation of in vitro properties, pharmaceutical performance, and biological activity of the obtained product. The composition of the formulation has a major influence on the properties of the final product obtained with low-energy emulsification methods. Increasing interest in high-energy emulsification methods is a consequence of their scalability important from the industrial perspective. Considering the high-energy emulsification methods, both the composition and conditions of the process (e.g., device power level, pressure, temperature, homogenization time, or number of cycles) are important for the properties and stability of nanoemulsions. It is advisible to determine the effect of each parameter on the quality of the product to establish the optimal process parameters' range which, in turn, results in a more reproducible and efficient production.