RESUMO
Holographic phase-shifting surfaces (PSSs) have been proven to offer a cost-effective solution for enabling passive arrays to mechanically steer their beams toward desired directions. However, even though the principle of operation of PSSs is straightforward, designing a PSS is very challenging, because it involves an extremely high computational time, which in turn limits their usage and development. Notably, traditional design approaches of PSSs, with N number of layers that have M different variations of conductive patches, need [Formula: see text] full-wave simulations to be properly characterized. To address these challenges that are associated with the design of PSSs and reduce the needed computational effort, we present here a semi-numerical approach that enables the efficient design of holographic PSSs. Specifically, by representing an N-layer PSS unit-cell as N cascaded networks, where each network represents one layer of the PSS that has M different designs of sub-wavelength resonators, we only need to conduct [Formula: see text] full-wave simulations to collect all the required data needed to analyze the performance of the PSS. In turn, by utilizing the multiplication property of ABCD parameters we can evaluate very efficiently all the [Formula: see text] different combinations that characterize our PSS. To validate the accuracy of our design methodology, a 1-D beam steerable antenna system is designed that is comprised of a circularly polarized holographic metasurface antenna (HMA) and a hybrid PSS, both operating at 30 GHz. Comparisons between our semi-numerical results, full-wave simulations, and measurements demonstrate an angular error of less than [Formula: see text].
RESUMO
Microwave absorbers have been used to mitigate signal interference, and to shield electromagnetic systems. Two different types of absorbers have been presented: (a) low-cost narrowband absorbers that are simple to manufacture, and (b) expensive wideband microwave absorbers that are based on complex designs. In fact, as designers try to increase the bandwidth of absorbers, they typically increase their complexity with the introduction of several electromagnetic components (e.g., introduction of multi-layer designs, introduction of multiple electromagnetic resonators, etc.,), thereby increasing their fabrication cost. Therefore, it has been a challenge to design wideband absorbers with low cost of fabrication. To address this challenge, we propose a novel design approach that combines origami math with electromagnetics to develop a simple to manufacture ultra-wideband absorber with minimal fabrication and assembly cost. Specifically, we utilize a Tachi-Miura origami pattern in a honeycomb configuration to create the first absorber that can maintain an absorptivity above 90% in a 24.6:1 bandwidth. To explain the ultra-wideband behavior of our absorber, we develop analytical models based on the transmission-reflection theory of electromagnetic waves through a series of inhomogeneous media. The ultra-wideband performance of our absorber is validated and characterized using simulations and measurements.
RESUMO
Frequency selective surfaces (FSSs) have been used to control and shape electromagnetic waves. Previous design approaches use complex geometries that are challenging to implement. With the purpose to transform electromagnetic waves, we morph the shapes of FSS designs based on origami patterns to attain new degrees of freedom and achieve enhanced electromagnetic performance. Specifically, using origami patterns with strongly coupled electromagnetic resonators, we transform a single-band FSS to a dual-band FSS. We explain this transformation by showing that both symmetric and anti-symmetric modes are excited due to the strong coupling and suitable orientation of the elements. Also, our origami FSS can fold/unfold thereby tuning (i.e., reconfiguring) its dual-band performance. Therefore, the proposed FSS is a dynamic reconfigurable electromagnetic structure whereas traditional FSSs are static and cannot change their performance.
RESUMO
Traditional electronic devices are rigid, planar, and mechanically static. The combination of traditional electronic materials and responsive polymer substrates is of significant interest to provide opportunities to replace conventional electronic devices with stretchable, 3D, and responsive electronics. Liquid crystal elastomers (LCEs) are well suited to function as such dynamic substrates because of their large strain, reversible stimulus response that can be controlled through directed self-assembly of molecular order. Here, we discuss using LCEs as substrates for electronic devices that are flat during processing but then morph into controlled 3D structures. We design and demonstrate processes for a variety of electronic devices on LCEs including deformation-tolerant conducting traces and capacitors and cold temperature-responsive antennas. For example, patterning twisted nematic orientation within the substrate can be used to create helical electronic devices that stretch up to 100% with less than 2% change in resistance or capacitance. Moreover, we discuss self-morphing LCE antennas which can dynamically change the operating frequency from 2.7 GHz (room temperature) to 3.3 GHz (-65 °C). We envision applications for these 3D, responsive devices in wearable or implantable electronics and in cold-chain monitoring radio frequency identification sensors.
