Advancements in Portable Voltammetry: A Promising Approach for Iron Speciation Analysis.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important as it impacts various aspects of our planet's health. The on-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for the on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination, the modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using the acetate buffer (pH = 4) as a supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV), and we used 1-(2-piridylazo)-2-naphthol (PAN) as the iron (III) ligand. Linearity, repeatability, detection limit, and accuracy were determined using synthetic solutions; then, a Standard Reference Material (SRM) of 1643f Trace Elements in Water (iron content: 93.44 ± 0.78 µg L-1) was used for validation measurements in the real matrix. the accuracy of this technique was found to be excellent since we obtained a recovery of 103.16%. The procedure was finally applied to real samples (tap, lake, and seawater), and the results obtained were compared via Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES). The amount of iron found was 207.8 ± 6.6 µg L-1 for tap water using voltammetry and 200.9 ± 1.5 µg L-1 with ICP-OES. For lake water, 171.7 ± 3.8 µg L-1, 169.8 ± 4.1 µg L-1, and 187.5 ± 5.7 µg L-1 were found using voltammetry in the lab both on-site and using ICP-OES, respectively. The results obtained demonstrate the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

Strategies for mercury speciation with single and multi-element approaches by HPLC-ICP-MS.

Mercury (Hg) and its compounds are highly toxic for humans and ecosystems, and their chemical forms determine both their behavior and transportation as well as their potential toxicity for human beings. Determining the various species of an element is therefore more crucial than understanding its overall concentration in samples. For this reason, several studies focus on the development of new analytical techniques for the identification, characterization, and quantification of Hg compounds. Commercially available, hyphenated technology, such as HPLC-ICP-MS, supports the rapid growth of speciation analysis. This review aims to summarize and critically examine different approaches for the quantification of mercury species in different samples using HPLC-ICP-MS. The steps preceding the quantification of the analyte, namely sampling and pretreatment, will also be addressed. The scenarios evaluated comprehend single and multi-element speciation analysis to create a complete guide about mercury content quantification.

Methods for Elemental Analysis of Size-Resolved PM Samples Collected on Aluminium Foils: Results of an Intercomparison Exercise.

Aluminium is the most common substrate in studies using impactors for the measurement of the number or the weight of size-segregated atmospheric particulate matter (PM), as its characteristics perfectly fit impactor requirements. However, its use is not recommended by manufacturers when one of the purposes of the study is the determination of the metal content in the sample. The aim of this work was to develop an efficient analytical procedure for the removal and acid digestion of PM samples collected on aluminium foils by a cascade impactor to perform the determination of metals. The possibility of performing the trace metal analysis of PM samples collected using aluminium foils is of great importance, as it allows the determination of an accurate size distribution and the elemental composition of the PM collected on each impactor stage. Two procedures were optimised by using different digestion and analysis techniques. Both procedures were then applied to the two halves of several Dekati low-pressure impactor (DLPI) samples, and the results were critically compared. The two procedures proved to be effective in the determination of extremely low concentrations of a large suite of analytes in different size fractions of PM emitted by a brake system.

Charge transfer modulation in charge transfer co-crystals driven by crystal structure morphology.

The electronic properties of a charge-transfer (donor-acceptor) semiconducting organic co-crystal, Perylene:F4-TCNQ (PE:F4) (the donor, D, is PE and the acceptor, A, is 2,3,5,6-tetrafluoro-7,7,8,8 tetracyanoquinodimethane (F4)) in its 3 : 2 stoichiometry, are experimentally and theoretically studied. This is performed by means of electron paramagnetic resonance (EPR) and solid state electrochemical techniques, such as cyclic voltammetry (CV) measurements on single crystals. In particular, solid state electrochemistry proves to be an effective tool to probe, on a macroscopic scale, the electronic characteristics of the co-crystal. However, EPR highlights the presence of spin ½ radicals localized on F4 molecules, possibly linked to defects. The experimental findings are discussed on the basis of density functional theory (DFT) based calculations, carried out using both the projector augmented wave (PAW), with "periodic boundary conditions" (pbc), method and the localized orbitals, molecular cluster, approach. In particular, a satisfying agreement is found between the experimental, 0.336 eV (electrochemical), and theoretical, 0.303 eV (PAW), band gaps. Differences with the reported optical bandgap are discussed considering excitonic effects.

On-Site Determination of Methylmercury by Coupling Solid-Phase Extraction and Voltammetry.

A measurement and speciation procedure for the determination of total mercury (HgTOT), inorganic mercury (HgIN), and methylmercury (CH3Hg) was developed and the applicability for on-site determination was demonstrated. A simple, portable sample pretreatment procedure was optimized to extract the analytes. Home-made columns, packed with a new sorbent material called CYXAD (CYPHOS 101 modified Amberlite XAD), were used to separate the two forms of the analyte. HgTOT and CH3Hg were determined by anodic stripping voltammetry (ASV), using a solid gold electrode (SGE). Two certified reference materials (BCR-463 Tuna Fish and Tuna Fish ERM-CE 464) and eight fresh fishes were analyzed. Then, the results that were obtained following the optimized portable procedure were compared with the concentrations obtained, using a direct mercury analyzer (DMA). This quantification, using the two techniques, demonstrated the good performance of the proposed method.

Macro and trace elements signature of periodontitis in saliva: A systematic review with quality assessment of ionomics studies.

OBJECTIVES: The present systematic review examined the available evidence on distinctive salivary ion profile in periodontitis compared to periodontal health and provided a qualitative assessment of the literature. BACKGROUND: Macro and trace elements are essential for cellular physiology, and their changes in biological fluids can be revelatory of an underlying pathological status. METHODS: Data from relevant studies identified from PubMed, Embase, and Scopus databases were retrieved to answer the following PECO question: "In systemically healthy individuals, are there any differences in any salivary macro or trace element concentration between periodontally healthy subjects (H) and patients with periodontitis (P)?" Quality of included studies was rated using a modified version of the QUADOMICS tool. A consistency analysis was performed to identify significantly discriminant chemical elements. RESULTS: After the screening of 873 titles, 13 studies were included reporting data on 22 different elements. Among them, levels of sodium and potassium were consistently and significantly higher in P compared to H. Conflicting results were found for all the other elements, despite concentration of calcium, copper, and manganese mostly increased in saliva of P. Levels of magnesium were found higher in P than in H in 2 studies but lower in 3. Zinc resulted significantly increased in saliva from H compared to P individuals in 2 studies, but one study reported opposite results. Four studies were considered as high quality, while reporting of operative protocols and statistical analysis was a major limitation for the others. Due to high methodologic heterogeneity, meta-analysis was not performed. CONCLUSIONS: Levels of macro or trace elements were differentially identified in saliva across diverse periodontal conditions, having a major potential for investigation of oral homeostasis and for high-resolution periodontal diagnosis. Products of inflammatory physiologic cellular impairment, such as sodium and potassium, were the most consistently associated with periodontitis (PROSPERO CRD42021235744).

Analytical Methods for the Characterization of Vegetable Oils.

The determination of the authenticity of extra virgin olive oils (EVOOs) has become more interesting in recent years. Italy is the first country in Europe in terms of number of Protected Designation of Origin (PDO) oils, which connects consumers to a feeling of tradition and thus to higher quality standards. This work focused on the consideration of the inorganic content as a possible marker of EVOOs. Ten vegetable oils (VOs), eight Italian EVOOs and seven not Italian EVOOs were analyzed. After pretreatment by acid mineralization, Al, Ba, Ca, Cu, Fe, K, Li, Mg, Mn, Na, P, Sb, Se and Zn were determined by ICP-OES. The electrochemical properties of a selected group of EVOOs and other vegetal oils of different botanical origin were investigated by voltammetry. Carbon paste electrodes (CPEs) were prepared. The features observed in the voltammograms reflect the reactions of electroactive compounds, which are present in the oils. A chemometric treatment of the results was performed to assess the possibility to distinguish (i) the region of provenience considering the inorganic profile; and (ii) the plant species from which each oil was obtained on the basis of the current profile registered during voltammetric analysis. Inorganic composition seems to be a useful marker for the assessment of the geographical origin of an EVOO. The EVOO-CPEs voltammetry seems to have a good ability to distinguish the plant species of origin. This method could be useful to monitor the conservation status of the oils, as the redox profile is linked to the oxidative degradation state.

Influence of start-up phase of an incinerator on inorganic composition and lead isotope ratios of the atmospheric PM10.

A municipal solid waste incinerator (MSWI) was installed in a peripheral area of the city of Turin. In this study, we evaluated the contribution of this plant to the massive concentration of PM10, to its chemical composition and to the distribution of the lead isotopes during the start-up phase.We assessed the inorganic composition of PM10 collected in the vicinity of the Turin incinerator by inductively coupled plasma atomic emission spectroscopy (ICP-AES), magnetic sector inductively coupled plasma mass spectrometer (SF-ICP-MS) and ion chromatography (IC). The lead isotope ratios in PM10 samples were determined by SF-ICP-MS by a method developed and optimized using experimental design approach. Element trends and data chemometric treatment evidence that the vehicular traffic, increased in this area due to the opening of the MSWI plant, and, to a lesser degree, the direct incinerator emissions influence As, Cd, Cr, Cu, Ba, Mo, Pb, Sn and Zn concentrations. As a whole, however, the element concentrations in PM10 and the Enrichment Factors (EFs) were comparable with the values reported for other urban sites and target pollutant concentrations of MSWI emissions, namely Cd, Cr, Cu and Pb, were lower than in PM10 emitted from older MSWIs. This confirms that incinerators of new installation have a lower impact on atmospheric PM10 composition thanks to stricter current legislation and up-to-date technologies. The lead isotope ratios investigation allowed to distinguish the diverse sources (crustal, vehicular traffic and MSWI) that influence lead concentration in PM10 collected near incinerator during start-up phase.

Development of an easy portable procedure for on-site determination of mercury and methylmercury.

A portable measurement and speciation procedure for inorganic mercury (HgIN) and methylmercury (CH3Hg) was developed. A portable sample pretreatment was optimized to determine total mercury content. A new home-made sorbent (CYXAD, CHYPOS 101 modified Amberlite XAD), was prepared to separate HgIN and CH3Hg. Mercury species were determined using square wave anodic stripping voltammetry (SW-ASV) with a solid gold electrode (SGE) and using a portable potentiostat. A certified reference material, five freeze-dried samples and three fresh samples were analysed with conventional voltammetric analyzer, after dissolution of the samples in microwave oven, and with a portable potentiostat after the mild eating procedure. The results obtained by SW-ASV were compared with those obtained using Direct Mercury Analyser (DMA). The quantification with the portable method is comparable to that obtained with the DMA. Retention tests showed the selectivity of CYXAD for HgIN, its stability and the possibility to re-use the same aliquot of resin.

Optimization of a sequential extraction procedure for trace elements in Arctic PM10.

In this work, a two-step sequential extraction scheme for the determination of trace elements in Arctic PM10 samples was optimized by using two certified reference materials (CRMs). By means of an experimental design for qualitative variables, the five most common extracting solutions for particulate matter (PM) sequential extraction (high purity water (HPW), 0.032 M HNO3, 0.022 M HCl, 0.11 M CH3COOH, and 0.012 M CH3COOH/CH3COONH4 buffer) and two different extraction methods (stirring and ultrasounds) were compared. The purpose of the study was the identification of the procedure which gives the best estimation of the anthropogenic portion of the elements present in PM10 samples. The use of ultrasounds instead of stirring induced a low but significant decrease of the extraction of all the elements and a decrease in the repeatability of the procedure. Diluted HNO3 was the extractant which allowed to maximize the extraction of anthropogenic elements (As, Cd, Pb, Zn) with respect to crustal ones (Al, Si, Ti). The optimized procedure proved successful in avoiding contaminations and, therefore, suitable to be applied to PM samples having extremely low concentrations, such as samples collected in polar or other remote areas. The chosen procedure was applied to ten Arctic PM10 samples, allowing for a better identification of their sources. Indeed, it was possible to hypothesize that even though the concentrations of As, Cd, K, Mg, Mn, and Ni in spring and summer were different, their mobility and, therefore, their chemical form in the analyzed PM10 samples were probably similar. Graphical abstract.

Modified Screen Printed Electrode Suitable for Electrochemical Measurements in Gas Phase.

We describe a convenient assembly for screen printed carbon electrodes (SPCE) suitable for analyses in gaseous samples which are of course lacking in supporting electrolytes. It consists of a circular crown of filter paper, soaked in a RTIL or a DES, placed upon a disposable screen printed carbon cell, so as to contact the outer edge of the carbon disk working electrode, as well as peripheral counter and reference electrodes. The electrical contact between the paper crown soaked in RTIL or DES and SPCE electrodes is assured by a gasket, and all components are installed in a polylactic acid holder. As a result of this configuration, a sensitive, fast-responding, membrane-free gas sensor is achieved where the real working electrode surface is the boundary zone of the carbon working disk contacted by the paper crown soaked in the polyelectrolyte. This assembly provides a portable and disposable electrochemical platform, assembled by the easy immobilization onto a porous and inexpensive supporting material such as paper of RTILs or DESs which are characterized by profitable electrical conductivity and negligible vapor pressure. The electroanalytical performance of this device was evaluated by voltammetric and flow injection analyses of oxygen which was chosen as prototype of electroactive gaseous analytes. The results obtained pointed out that this assembly is very profitable for the analysis of gaseous atmospheres, especially when used as detector for FIA in gaseous streams.

The Inorganic Component as a Possible Marker for Quality and for Authentication of the Hazelnut's Origin.

The inorganic component of hazelnuts was considered as a possible marker for geographical allocation and for the assessment of technological impact on their quality. The analyzed samples were Italian hazelnuts of the cultivar Tonda Gentile Romana and Turkish hazelnuts of the cultivars Tombul, Palaz and Çakildak. The hazelnuts were subjected to different drying procedures and different conservative methods. The concentration of 13 elements, namely Ba, Ca, Cu, Fe, K, Mg, Mn, Na, Ni, P, Sn, Sr and Zn, were quantified by inductively coupled plasma optical emission spectroscopy (ICP-OES). All the samples were previously digested in a microwave oven. Before proceeding with the analysis of the samples, the whole procedure was optimized and tested on a certified reference material. The results show that the inorganic component: (i) can represent a fingerprint, able to identify the geographical origin of hazelnuts, becoming an important quality marker for consumer protection; (ii) is strongly influenced by the treatments undergone by the investigated product during all the processing stages. A pilot study was also carried out on hazelnuts of the cultivar Tonda Gentile Trilobata Piemontese, directly harvested from the plant during early development to maturity and analyzed to monitor the element concentration over time.

A Portable Setup for the Voltammetric Determination of Total Mercury in Fish with Solid and Nanostructured Gold Electrodes.

A simple procedure for field fish sample pretreatment was developed. This treatment in combination with square wave anodic stripping voltammetry (SW-ASV) with solid gold electrodes (SGE) and gold nanoparticle-modified glassy carbon electrodes (AuNPs-GCE) was applied for the determination of total mercury content. A certified reference material (CRM, Tuna Fish BCR 463), ten freeze-dried samples of canned tuna and two fresh fish samples were analysed both with a bench-top voltammetric analyser after microwave digestion and with a portable potentiostat after mild eating using a small commercial food warmer. The results obtained by the two SW-ASV approaches and by a Direct Mercury Analyser (DMA), the official method for mercury determination, were in very good agreement. In particular, (i) the results obtained with in field procedure are consistent with those obtained with the conventional microwave digestion; (ii) the presence of gold nanoparticles on the active electrode surface permits an improvement of the analytical performance in comparison to the SGE: the Limit of Quantification (LOQ) for mercury in fish-matrix was 0.1 µg L-1 (Hg cell concentration), corresponding to 0.06 mg kg-1 wet fish, which is a performance comparable to that of DMA. The pretreatment proposed in this study is very easy and applicable to fresh fish; in combination with a portable potentiostat, it proved to be an interesting procedure for on-site mercury determination.

Microwave-Assisted Dehydrogenative Cross Coupling Reactions in γ-valerolactone with a Reusable Pd/ß-cyclodextrin Crosslinked Catalyst.

Transition-metal mediated C⁻H bond activation and functionalization is one of the most straightforward and powerful tools in modern organic synthetic chemistry. Oxidative C⁻H/C⁻H coupling reactions between two (hetero)arenes under heterogeneous catalysis may be a valuable means for the production of a plethora of bi(hetero)aryls, and one that adheres to the increasing demand for atom-economic and sustainable chemistry. We have therefore developed a reusable heterogeneous catalytic system, which is based on Pd cross-linked ß-cyclodextrin, to perform an efficient microwave-assisted oxidative C⁻H/C⁻H cross coupling process between benzothiazoles and methyl thiophene in the presence of green solvents.

Comprehensive study on the degradation of ochratoxin A in water by spectroscopic techniques and DFT calculations.

Ochratoxin A (OTA) is one of the most important dietary risk factors and is classified as a possible carcinogen to humans. Assessing the conditions to remove it from foodstuffs in a simple and effective way is of the utmost importance. OTA behaviour in water in the pH range 1.0-12.5 was elucidated to investigate the conditions for irreversible toxicity inactivation of OTA. The results indicate that four forms, from neutral to trianionic, intervene depending on the pH. pK a1,2 were rigorously established by independent spectroscopic techniques to overcome the scarcity of literature. Then, Density Functional Theory (DFT) calculations were used to determine the most probable degradation mechanism and this was confirmed by fluorescence spectroscopy. At pH 12.5, hydrolyzation of the lactone ring starts in less than one hour, but only after two hours does the degradation process lead to fragmentation. After one week this process is not yet completed. The reaction products occurring upon re-acidification were also investigated. OTA degradation is still reversible if acidic conditions are promptly restored, yielding again a hazardous molecule. However, degradation becomes irreversible after fragmentation. This finding suggests proceeding with due caution if a base is exploited to remove the toxin.

Off-line and real-time monitoring of acetaminophen photodegradation by an electrochemical sensor.

The photochemistry of N-acetyl-para-aminophenol (acetaminophen, APAP) is here investigated by using differential pulse voltammetry (DPV) analysis to monitor APAP photodegradation upon steady-state irradiation. The purpose of this work is to assess the applicability of DPV to monitor the photochemical behaviour of xenobiotics, along with the development of an electrochemical set-up for the real-time monitoring of APAP photodegradation. We here investigated the APAP photoreactivity towards the main photogenerated reactive transients species occurring in sunlit surface waters (hydroxyl radical HO, carbonate radical CO3-, excited triplet state of anthraquinone-2-sulfonate used as proxy of the chromophoric DOM, and singlet oxygen 1O2), and determined relevant kinetic parameters. A standard procedure based on UV detection coupled with liquid chromatography (HPLC-UV) was used under identical experimental conditions to compare and verify the DPV-based results. The latter were in agreement with HPLC data, with the exception of the triplet-sensitized processes. In the other cases, DPV could be used as an alternative to the well-tested but more costly and time-consuming HPLC-UV technique. We have also assessed the reaction rate constant between APAP and HO by real-time DPV, which allowed for the monitoring of APAP photodegradation inside the irradiation chamber. Unfortunately, real-time DPV measurements are likely to be affected by temperature variations of the irradiated samples. Overall, DPV appeared as a fast, cheap and reasonably reliable technique when used for the off-line monitoring of APAP photodegradation. When a suitable real-time procedure is developed, it could become a very straightforward method to study the photochemical behaviour of electroactive xenobiotics.

Chromium, nickel, and cobalt in cosmetic matrices: an integrated bioanalytical characterization through total content, bioaccessibility, and Cr(III)/Cr(VI) speciation.

The presence of certain metals naturally contained inside raw materials (e.g., pigments) used to produce cosmetics for make-up may represent a serious concern for the final quality and safety of the product. The knowledge of the total concentration of metals is not sufficient to predict their reactivity and their toxicological profile. For these reasons, we set up a comprehensive approach to characterize the content of Co, Cr, and Ni in two raw materials for cosmetic production, a black iron oxide and a pearly pigment, and in a finished product, pearly powder eye shadow. Namely, besides the total metal concentrations, the speciation of chromium and the bioaccessibility of the three metals were assessed. Since no standard method is so far available for hexavalent chromium extraction from cosmetic samples, three approaches were compared (EPA 3060A method, IRSA 16 method, and a Na3PO4 extraction). Results show that Na3PO4 extraction is the most selective one. Cr(VI) was undetectable in black iron oxide and present at very low concentrations (about 0.3 mg/kg) in pearly pigment and in the pearly powder eye shadow samples. The extracted Cr(VI) concentrations are not related to the total Cr content in the samples. Bioaccessibility studies were performed by in vitro extractions with synthetic lacrimal fluids and sweat. Despite the wide range of metal concentrations in the samples, the amounts of bioaccessible elements were undetectable or very low (less than 0.4 mg/kg), thus suggesting that metals in the three samples are present in inert forms. Graphical abstract The possible leaching of metals from cosmetics to biological fluids. Spectroscopic and chromatographic techniques provide complementary information for an integrated bioanalytical approach to risk characterization.

Element variability in lacustrine systems of Terra Nova Bay (Antarctica) and concentration evolution in surface waters.

Major, minor and trace elements were determined in freshwater of lacustrine systems in Terra Nova Bay, along Victoria Land coast, Antarctica, as well as in algae and mosses. The samples were collected during some of the sampling campaigns between 2007 and 2011 (and the one of 2002) within the framework of the Italian National Program of Research in Antarctica (PNRA). Data were processed with chemometric techniques. Results showed that elements typically considered as potential anthropogenic pollutants (e.g. As, Pb, Zn, Cu and Ni) present a strong correlation with the lithogenic elements (e.g. Al, Si, Fe) in all matrices, suggesting that their origin is connected to natural phenomena. Metal concentrations in vegetation samples are in the same range as previously published data. The obtained results were compared with older literature data (since the early '90s) from the same lacustrine systems, in order to present a historical overview of element concentrations. This approach furnishes important information on surface water evolution as a function of time. A considerable variability was observed in metal concentrations but no clear trend was identified. This suggests that their concentration evolution is hardly correlated to specific natural or anthropic phenomena. No evidence of an increase of concentrations over time was apparent. Our results represent new important data about metal concentrations in lacustrine systems in Antarctica, furnishing ranges of values that can be considered as a reference. These data, therefore, could be used to detect or monitor future local and/or global anthropogenic contaminations.

Anodic stripping voltammetry with gold electrodes as an alternative method for the routine determination of mercury in fish. Comparison with spectroscopic approaches.

The applicability to the determination of mercury in tuna of square wave anodic stripping voltammetry (SW-ASV) conducted at both solid gold electrode (SGE) and a gold nanoparticle-modified glassy carbon electrode (AuNPs-GCE) was demonstrated. Mercury content in two certified materials and in ten samples of canned tuna was measured. The performances of the electrodes were compared with one another as well as with two spectroscopic techniques, namely cold vapour atomic absorption spectroscopy (CV-AAS) and a direct mercury analyser (DMA). The results found pointed out that both SW-ASV approaches were suitable and easy-to-use method to monitor mercury concentration in tunas, since they allowed accurate quantification at concentration values lower than the maximum admissible level in this matrix ([Hg]=1mg/kgwet weight,ww). In particular, mercury detection at the AuNPs-GCE showed a LOQ in fish-matrix of 0.1µg/l, corresponding to 0.06mg/kgww, with performance comparable to that of DMA.

Ultrasonically improved semi-hydrogenation of alkynes to (Z-)alkenes over novel lead-free Pd/Boehmite catalysts.

This paper reports the application of ultrasound in the semi-hydrogenation of alkynes over two novel Pd/Boehmite catalysts. The semi-hydrogenations of phenylacetylene, diphenylacetylene and 2-butyne-1,4-diol have either been investigated in an ultrasonic bath under atmospheric hydrogen pressure, or in an ultrasonic horn reactor under 0.1-0.5MPa hydrogen pressure. Alkyne hydrogenation was suppressed by sonication under atmospheric hydrogen pressure, but promoted by sonication under 0.1MPa of hydrogen pressure. Sonication increased selectivity towards the semi-hydrogenated products in both cases. Catalyst loading, hydrogen pressure, temperature and the presence of quinoline, all impacted on hydrogenation rate, activity and selectivity to semi-hydrogenated products. Palladium leaching from the catalyst was evaluated in ethanol and hexane both under plain stirring and sonication.