Pure Iodide Multication Wide Bandgap Perovskites by Vacuum Deposition.

The CsPbI3 perovskite has a suitable bandgap (≈1.7 eV) for application in tandem solar cells. One challenge for this compound is that the semiconducting perovskite phase is not stable at room temperature, when it tends to form a yellow nonperovskite phase with a bandgap of approximately 2.8 eV. Therefore, many reports have been focused on the stabilization of the CsPbI3 black perovskite phase through the use of additives during solution processing. Vacuum deposited CsPbI3 has been seldom reported, as in this case, the insertion of stabilizing agents is more challenging. In this work, we demonstrate the vacuum processing of CsPbI3 perovskite films at room temperature, obtained by incorporating dimethylammonium iodide by cosublimation with CsI and PbI2. As-prepared films were applied in planar solar cells, leading to an average power conversion efficiency (PCE) exceeding 12%. In order to improve the device performance, we introduced a third A-site cation (methylammonium) in a four-source deposition process. This pure iodide formulation can be used in wide bandgap solar cells with a PCE up to 14.8%.

Perovskite/Perovskite Tandem Solar Cells in the Substrate Configuration with Potential for Bifacial Operation.

Perovskite/perovskite tandem solar cells have recently exceeded the record power conversion efficiency (PCE) of single-junction perovskite solar cells. They are typically built in the superstrate configuration, in which the device is illuminated from the substrate side. This limits the fabrication of the solar cell to transparent substrates, typically glass coated with a transparent conductive oxide (TCO), and adds constraints because the first subcell that is deposited on the substrate must contain the wide-bandgap perovskite. However, devices in the substrate configuration could potentially be fabricated on a large variety of opaque and inexpensive substrates, such as plastic and metal foils. Importantly, in the substrate configuration the narrow-bandgap subcell is deposited first, which allows for more freedom in the device design. In this work, we report perovskite/perovskite tandem solar cells fabricated in the substrate configuration. As the substrate we use TCO-coated glass on which a solution-processed narrow-bandgap perovskite solar cell is deposited. All of the other layers are then processed using vacuum sublimation, starting with the charge recombination layers, then the wide-bandgap perovskite subcell, and finishing with the transparent top TCO electrode. Proof-of-concept tandem solar cells show a maximum PCE of 20%, which is still moderate compared to those of best-in-class devices realized in the superstrate configuration yet higher than those of the corresponding single-junction devices in the substrate configuration. As both the top and bottom electrodes are semitransparent, these devices also have the potential to be used as bifacial tandem solar cells.

Quadruple-Cation Wide-Bandgap Perovskite Solar Cells with Enhanced Thermal Stability Enabled by Vacuum Deposition.

Vacuum processing of multicomponent perovskites is not straightforward, because the number of precursors is in principle limited by the number of available thermal sources. Herein, we present a process which allows increasing the complexity of the formulation of vacuum-deposited lead halide perovskite films by multisource deposition and premixing both inorganic and organic components. We apply it to the preparation of wide-bandgap CsMAFA triple-cation perovskite solar cells, which are found to be efficient but not thermally stable. With the aim of stabilizing the perovskite phase, we add guanidinium (GA+) to the material formulation and obtained CsMAFAGA quadruple-cation perovskite films with enhanced thermal stability, as observed by X-ray diffraction and rationalized by microstructural analysis. The corresponding solar cells showed similar performance with improved thermal stability. This work paves the way toward the vacuum processing of complex perovskite formulations, with important implications not only for photovoltaics but also for other fields of application.

Efficient Wide-Bandgap Mixed-Cation and Mixed-Halide Perovskite Solar Cells by Vacuum Deposition.

Vacuum deposition methods are increasingly applied to the preparation of perovskite films and devices, in view of the possibility to prepare multilayer structures at low temperature. Vacuum-deposited, wide-bandgap solar cells based on mixed-cation and mixed-anion perovskites have been scarcely reported, due to the challenges associated with the multiple-source processing of perovskite thin films. In this work, we describe a four-source vacuum deposition process to prepare wide-bandgap perovskites of the type FA1-n Cs n Pb(I1-x Br x )3 with a tunable bandgap and controlled morphology, using FAI, CsI, PbI2, and PbBr2 as the precursors. The simultaneous sublimation of PbI2 and PbBr2 allows the relative Br/Cs content to be decoupled and controlled, resulting in homogeneous perovskite films with a bandgap in the 1.7-1.8 eV range and no detectable halide segregation. Solar cells based on 1.75 eV bandgap perovskites show efficiency up to 16.8% and promising stability, maintaining 90% of the initial efficiency after 2 weeks of operation.

Co-Evaporated p-i-n Perovskite Solar Cells beyond 20% Efficiency: Impact of Substrate Temperature and Hole-Transport Layer.

For methylammonium lead iodide perovskite solar cells prepared by co-evaporation, power conversion efficiencies of over 20% have been already demonstrated, however, so far, only in n-i-p configuration. Currently, the overall major challenges are the complex evaporation characteristics of organic precursors that strongly depend on the underlying charge selective contacts and the insufficient reproducibility of the co-evaporation process. To ensure a reliable co-evaporation process, it is important to identify the impact of different parameters in order to develop a more detailed understanding. In this work, we study the influence of the substrate temperature, underlying hole-transport layer (polymer PTAA versus self-assembling monolayer molecule MeO-2PACz), and perovskite precursor ratio on the morphology, composition, and performance of co-evaporated p-i-n perovskite solar cells. We first analyze the evaporation of pure precursor materials and show that the adhesion of methylammonium iodide (MAI) is significantly reduced with increased substrate temperature, while it remains almost unaffected for lead iodide (PbI2). This substrate temperature-dependent evaporation behavior of MAI is also transferred to the co-evaporation process and can directly influence the perovskite composition. We demonstrate that the optimal substrate temperature window for perovskite deposition is close to room temperature. At high temperature, not enough MAI for precise stoichiometry is incorporated even with very high MAI rates. While, at temperatures below -25 °C, the conversion of MAI with PbI2 is inhibited, and an amorphous yet unreacted film is formed. We observe that perovskite composition and morphology vary widely between the organic hole-transport layers (HTLs) PTAA and MeO-2PACz. For all substrate temperatures, MeO-2PACz enables higher solar cell PCEs than PTAA. Through the combination of vapor-deposited perovskites and a self-assembled monolayer, we achieve a stabilized power conversion efficiency of 20.6%, which is the first reported PCE above 20% for evaporated perovskite solar cells in p-i-n architecture.

Deposition Kinetics and Compositional Control of Vacuum-Processed CH3NH3PbI3 Perovskite.

Halide perovskites have generated considerable research interest due to their excellent optoelectronic properties in the past decade. To ensure the formation of high-quality semiconductors, the deposition process for the perovskite film is a critical issue. Vacuum-based processing is considered to be a promising method, allowing, in principle, for uniform deposition on a large area. One of the benefits of vacuum processing is the control over the film composition through the use of quartz crystal microbalances (QCMs) that monitor the rates of the components in situ. In metal halide perovskites, however, one frequently employed component or precursor, CH3NH3I, exhibits nonstandard sublimation properties. Here, we study in detail the sublimation properties of CH3NH3I and demonstrate that by correcting for its complex adsorption properties and by modeling the film growth, accurate predictions of the stoichiometry of the final perovskite film can be obtained.

Efficient Vacuum Deposited P-I-N Perovskite Solar Cells by Front Contact Optimization.

Hole transport layers (HTLs) are of fundamental importance in perovskite solar cells (PSCs), as they must ensure an efficient and selective hole extraction, and ohmic charge transfer to the corresponding electrodes. In p-i-n solar cells, the ITO/HTL is usually not ohmic, and an additional interlayer such as MoO3 is usually placed in between the two materials by vacuum sublimation. In this work, we evaluated the properties of the MoO3/TaTm (TaTm is the HTL N4,N4,N4″,N4″-tetra([1,1'-biphenyl]-4-yl)-[1,1':4',1″-terphenyl]-4,4″-diamine) hole extraction interface by selectively annealing either MoO3 (prior to the deposition of TaTm) or the bilayer MoO3/TaTm (without pre-treatment on the MoO3), at temperature ranging from 60 to 200°C. We then used these p-contacts for the fabrication of a large batch of fully vacuum deposited PSCs, using methylammonium lead iodide as the active layer. We show that annealing the MoO3/TaTm bilayers at high temperature is crucial to obtain high rectification with low non-radiative recombination, due to an increase of the electrode work function and the formation of an ohmic interface with TaTm.

Recombination in Perovskite Solar Cells: Significance of Grain Boundaries, Interface Traps, and Defect Ions.

Trap-assisted recombination, despite being lower as compared with traditional inorganic solar cells, is still the dominant recombination mechanism in perovskite solar cells (PSCs) and limits their efficiency. We investigate the attributes of the primary trap-assisted recombination channels (grain boundaries and interfaces) and their correlation to defect ions in PSCs. We achieve this by using a validated device model to fit the simulations to the experimental data of efficient vacuum-deposited p-i-n and n-i-p CH3NH3PbI3 solar cells, including the light intensity dependence of the open-circuit voltage and fill factor. We find that, despite the presence of traps at interfaces and grain boundaries (GBs), their neutral (when filled with photogenerated charges) disposition along with the long-lived nature of holes leads to the high performance of PSCs. The sign of the traps (when filled) is of little importance in efficient solar cells with compact morphologies (fused GBs, low trap density). On the other hand, solar cells with noncompact morphologies (open GBs, high trap density) are sensitive to the sign of the traps and hence to the cell preparation methods. Even in the presence of traps at GBs, trap-assisted recombination at interfaces (between the transport layers and the perovskite) is the dominant loss mechanism. We find a direct correlation between the density of traps, the density of mobile ionic defects, and the degree of hysteresis observed in the current-voltage (J-V) characteristics. The presence of defect states or mobile ions not only limits the device performance but also plays a role in the J-V hysteresis.

Perovskite Luminescent Materials.

We describe recent progress on the luminescent properties of hybrid organic inorganic metal halide perovskites and the LEDs employing them.

Regioisomerism in cationic sulfonyl-substituted [Ir(C

A series of regioisomeric cationic iridium complexes of the type [Ir(C^N)2(bpy)][PF6] (bpy = 2,2'-bipyridine) is reported. The complexes contain 2-phenylpyridine-based cyclometallating ligands with a methylsulfonyl group in either the 3-, 4- or 5-position of the phenyl ring. All the complexes have been fully characterized, including their crystal structures. In acetonitrile solution, all the compounds are green emitters with emission maxima between 493 and 517 nm. Whereas substitution meta to the Ir-C bond leads to vibrationally structured emission profiles and photoluminescence quantum yields of 74 and 77%, placing a sulfone substituent in a para position results in a broad, featureless emission band, an enhanced quantum yield of 92% and a shorter excited-state lifetime. These results suggest a larger ligand-centred ((3)LC) character of the emissive triplet state in the case of meta substitution and a more pronounced charge transfer (CT) character in the case of para substitution. Going from solution to the solid state (powder samples and thin films), the emission maxima are red-shifted for all the complexes, resulting in green-yellow emission. Data obtained from electrochemical measurements and density functional theory calculations parallel the photophysical trends. Light-emitting electrochemical cells (LECs) based on the complexes were fabricated and evaluated. A maximum efficiency of 4.5 lm W(-1) at a maximum luminance of 940 cd m(-2) was observed for the LEC with the complex incorporating the sulfone substituent in the 4-position when operated under pulsed current driving conditions.

Perovskite solar cells prepared by flash evaporation.

A simple vacuum deposition method for the preparation of high quality hybrid organic-inorganic methylammonium lead iodide perovskite thin films is reported. When sandwiched in between organic charge transporting layers, such films lead to solar cells with a power conversion efficiency of 12.2%.

Mixed Iodide-Bromide Methylammonium Lead Perovskite-based Diodes for Light Emission and Photovoltaics.

Vacuum deposition techniques are used to prepare mixed iodide-bromide methylammonium lead perovskite diodes via an intermediate double layer of the pure iodide and bromide perovskites. The diodes lead to bright electroluminescence, whose emission spectra maxima shift from the infrared toward the visible with increasing bromide content. When illuminated with AM1.5 simulated sunlight the devices function as efficient solar cells with power conversion efficiencies as high as 12.9%.

Exceptionally long-lived light-emitting electrochemical cells: multiple intra-cation π-stacking interactions in [Ir(C

A series of cyclometalated iridium(iii) complexes [Ir(C^N)2(N^N)][PF6] (N^N = 2,2'-bipyridine (1), 6-phenyl-2,2'-bipyridine (2), 4,4'-di-tert-butyl-2,2'-bipyridine (3), 4,4'-di-tert-butyl-6-phenyl-2,2'-bipyridine (4); HC^N = 2-(3-phenyl)phenylpyridine (HPhppy) or 2-(3,5-diphenyl)phenylpyridine (HPh2ppy)) are reported. They have been synthesized using solvento precursors so as to avoid the use of chlorido-dimer intermediates, chloride ion contaminant being detrimental to the performance of [Ir(C^N)2(N^N)][PF6] emitters in light-electrochemical cell (LEC) devices. Single crystal structure determinations and variable temperature solution 1H NMR spectroscopic data confirm that the pendant phenyl domains engage in multiple face-to-face π-interactions within the coordination sphere of the iridium(iii) centre. The series of [Ir(Phppy)2(N^N)]+ and [Ir(Ph2ppy)2(N^N)]+ complexes investigated include those with and without intra-cation face-to-face π-stacking. All the complexes display excellent luminescent properties, in particular when employed in thin solid films. The most important observation is that all the LECs using the [Ir(Phppy)2(N^N)]+ and [Ir(Ph2ppy)2(N^N)]+ emitters (i.e. with and without intra-cation π-stacking interactions) exhibit very stable luminance outputs over time, even when driven at elevated current densities. The most stable LEC had an extrapolated lifetime of more than 2500 hours under accelerated testing conditions.

Efficient photovoltaic and electroluminescent perovskite devices.

Planar diode structures employing hybrid organic-inorganic methylammonium lead iodide perovskites lead to multifunctional devices exhibiting both a high photovoltaic efficiency and good electroluminescence. The electroluminescence strongly improves at higher current density applied using a pulsed driving method.